Technical description and composition of the SUPRA STV-LC32LT0060W TV, panel type and modules used. The composition of the modules.SUPRA LED
Model: STV-LC32LT0060W
Chassis / Version: V1T07
Panel: LSC320AN10
LED driver (backlight): integrated into MainBoard
PWM LED driver: SO-8
MOSFET LED driver: TO-252
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: TO-252
MainBoard: TP.MS3663S.PB818
IC MainBoard: CPU: MSD3663LSA-SW, SPI Flash 25Q64
Tuner: CDT-9NT372-RF01
STV-LC32LT0060W Specifications
SUPRA STV-LC32LT0060W
General recommendations for TV LCD LED repair
Possible malfunctions
- SUPRA STV-LC32LT0060W TV does not turn on at all. No response to the remote control and front panel control buttons. Indicator lamps do not light up or flash.
In this case, the main Switching Power Supply - the AC / DC mains voltage converter, the elements of which are located on the MainBoard TP.MS3663S.PB818, may be faulty. In the absence of the necessary supply voltages in the secondary circuits of the converters, it is necessary to check the power switches (TO-252) and rectifier diodes for possible partial or complete breakdown.
In case of breakdowns in the secondary circuits, the converter, as a rule, can operate in an emergency in the short-circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse is usually cut off.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements, which can disable it in key mode, or provoke an excess of the maximum current or voltage values. These can be circuits supplying the PWM controller, damper or frequency setting circuits, or OOS (negative feedback) elements in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6, in the absence of external damage and a short circuit between the terminals, are checked by replacing them with a known good one.
- There is no picture, there is sound, it reacts to the remote control, the channels are switched. In some cases, the image appears when turned on and disappears immediately.
The backlight of the matrix (LED-panel) is usually faulty in these cases. Usually, the cause of the malfunction is in the breakage of the LEDs, or in the connectors of the LED strips, but sometimes the LED driver is also faulty.
It is impossible to check the LED bars for a break without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters tend to light a single 3V LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as an indicator of serviceability. In faulty LEDs, the zener diode will either be cut off, or pierced in the K / Z.
- The TV does not turn on, the indicator signals standby or operating mode, or blinks.
Repair or diagnostics of the TP.MS3663S.PB818 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Complex repair of MB (SSB) is possible only in a service center with the necessary equipment. Checking or replacing CPU elements: MSD3663LSA-SW, SPI Flash 25Q64 requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by the warm-up method.
Before changing the CDT-9NT372-RF01 tuner, if it is not possible to tune to TV channels, you should make sure that there are supply voltages, which must be measured at the corresponding tuner terminals and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be monitored with an oscilloscope
Remember! Attempts to self-repair the SUPRA STV-LC32LT0060W TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
Additional MainBoard RepairThe appearance of MainBoard TP.MS3663S.PB818 is shown in the figure below:
TP.MS3663S.PB818
Main features of SUPRA STV-LC32LT0060W device:
Installed matrix (LED panel) LSC320AN10.
To power the backlight LEDs, a converter combined with the main board TP.MS3663S.PB818 is used, controlled by the SO-8 PWM controller. TO-252 switches are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using SOT23-6 PWM microcircuits and TO-252 power switches.
MainBoard - the main board (motherboard) is a TP.MS3663S.PB818 module, using CPU chips: MSD3663LSA-SW, SPI Flash 25Q64 and others.
The CDT-9NT372-RF01 tuner provides reception of television programs and tuning to channels.
SUPRA LED TV STV-LC32LT0060W with LCD LSC320AN10, 32 "(81 cm) 16: 9. depending on the illumination of the areas in the scene. The LED panel uses direct pixel backlighting with LED back-mounted - Direct LED. It is possible to view broadcasts and movies and images in high quality HD at a resolution of 1366x768 pixels in the 720p (HD Ready) graphics standard. multimedia file formats: MP3, MPEG4, MKV, JPEG.
Speaker power 10 W (2x5 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, VGA, HDMI x3, USB. A headphone output is provided. The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
The power consumed by the TV in operating mode from the network is 60 watts.
Dimensions: with stand 735x465x210 mm, without stand 735x410x79 mm.
TV weight: with stand: 4.3 kg, without stand: 4.2 kg.
Attention! The panel LSC320AN10 of the SUPRA STV-LC32LT0060W LED TV is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV non-repairable.