Monday, 3 August 2020

REPAIRING / SERVICING TV SUPRA STV-LC32LT0080W

 Technical description and composition of the SUPRA STV-LC32LT0080W TV, panel type and modules used. The composition of the modules.
SUPRA LED
Model: STV-LC32LT0080W
Chassis / Version: V1T09
Panel: V320BJ6-Q01
LED backlight: LED315D10-07 (B) 30331510219
LED driver (backlight): integrated into MainBoard
PWM LED driver: 8pin
MOSFET LED driver: TO-252
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: TO-252
MainBoard: TP.MS3663T.PB751
IC MainBoard: CPU: MSD3663LSAT, SPI Flash: 25Q64
Tuner: CDT-9NT372-RF01 & SAT
STV-LC32LT0080W Specifications
SUPRA STV-LC32LT0080W
General recommendations for TV LCD LED repair
Possible malfunctions
- The SUPRA STV-LC32LT0080W TV does not turn on, does not respond to the remote control and control panel buttons, the indicators are off or flashing.
In this case, first of all, you should check the operability of the main power source - AC / DC voltage converter, all elements of which are located on the MainBoard TP.MS3663T.PB751. It is necessary to measure the output voltages in its secondary circuits, and if they are completely absent, the serviceability of the power switches (TO-252) and rectifier diodes should be checked for possible breakdown (short circuit).
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in an emergency mode of short circuit without output voltages, and with a short circuit in the elements of the primary circuit, the mains fuse most often breaks off immediately and less often the current sensor in the source of the key.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can disable it in the key mode, or create an excess of the maximum permissible key parameters. These can be elements supplying a PWM regulator, frequency setting or damper circuits, or elements of negative feedback in the stabilization circuit. PWM controllers PWM SOT23-6, in the absence of visible damage or outright short circuits between the terminals, are checked by replacing them with new ones, or knowingly working properly.
- There is no picture, but there is sound, it reacts to the remote control. Or the image appears when turned on and disappears immediately
The malfunction in most of these cases is found in the nodes and elements of the LED panel backlighting. The reason may be in the breakage of the LEDs, in the stabilization of their power supply, or in the violation of the contact connections of the strings connectors,
To test the LED strips, to open all the transitions of the LEDs, you need several tens of volts or more, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED junctions in forward bias, you can sometimes detect the presence of a protective zener diode PN junction by connecting the probes in the opposite direction. If the zener diode is cut off or broken in K / Z, then the LED is faulty and requires replacement.
- The indicator on the front panel blinks, the TV does not turn on in operating mode, does not respond to the remote control.
Repair or diagnostics of the TP.MS3663T.PB751 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). In some cases, to repair the MB (SSB) board, it may be necessary to replace the chips - CPU: MSD3663LSAT, SPI Flash: 25Q64 with new or known good ones. In cases where BGA technologies are used, defects are usually localized by heating.
If the TV operates normally from external devices, but does not tune to TV channels, the CDT-9NT372-RF01 & SAT tuner may be faulty. In such cases, first of all, you should make sure that the supply voltage is present at its corresponding terminals. It is also necessary to make sure that the data exchange between the tuner and the processor is possible via the I2C bus. Sometimes the reason for the inoperability of the tuner may be a software failure.
Once again, we remind TV users: do not attempt to repair yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair to professionals with sufficient experience in the field of electronic repair.


DOWNLOAD FIRMWARE FOR SPI FLASH  ----------->   SUPRA STV-LC32LT0080W V1T09, Main: TP.MS3663T.PB751, Panel: V320BJ6-Q01


 The appearance of the MainBoard TP.MS3663T.PB751 is shown in the figure below:
TP.MS3663T.PB751
Main features of SUPRA STV-LC32LT0080W device:
Installed matrix (LED panel) V320BJ6-Q01.
To power the backlight LEDs, a converter combined with the main board TP.MS3663T.PB751 is used, controlled by an 8pin PWM controller. TO-252 switches are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using SOT23-6 PWM microcircuits and TO-252 power switches.
MainBoard - the main board (motherboard) is a TP.MS3663T.PB751 module, using CPU chips: MSD3663LSAT, SPI Flash: 25Q64 and others.
The CDT-9NT372-RF01 & SAT tuner provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: V320BJ6-Q01
Type: a-Si TFT-LCD, CELL
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: MVA, Normally Black, Transmissive
Active Area: 697.685x392.256 mm
Surface: Antiglare (Haze 2%)
Transmissivity: 6.0% (with Polarizer)
Contrast Ratio: 3000: 1
Display Colors: 16.7M (6-bit + Hi-FRC)
Response Time: 8.5 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
SUPRA LED TV STV-LC32LT0080W with V320BJ6-Q01 LCD, 32 "(81 cm) 16: 9 format diagonal. The required screen brightness of 220 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 100,000: 1 is achieved by special control operation of LEDs depending on the illumination of areas in the scene.The model's display technology uses LED LED backlighting.It is possible to view broadcasts and films and images in high quality HD at a resolution of 1366x768 pixels in the 720p graphic resolution standard (HD Ready) .Supported media file formats: MP3, WMA, MPEG4, HEVC (H.265), MKV, JPEG.
Speaker power 12 W (2x6 W) is provided by two speakers. Uses NICAM stereo signal processing system and Sound Surround function.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, HDMI x2, USB. The digital tuner is capable of receiving TV channels in the DVB-T MPEG4, DVB-C, DVB-T2, DVB-S2 standards.
The power consumed by the TV in operating mode from the network is 60 watts.
Dimensions: with stand 733x477x195 mm, without stand 733x435x80 mm.
Attention! The panel V320BJ6-Q01 of the SUPRA STV-LC32LT0080W LED TV is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV non-repairable.