Technical description and composition of the TELEFUNKEN TF-LED29S30T2 TV, panel type and modules used. The composition of the modules.TELEFUNKEN LED
Model: TF-LED29S30T2
Chassis / Version: CV9202H-TPW
Panel: V290BJ1-XC01 CX290DLEDM
LED driver (backlight): integrated into PSU
PWM LED driver: OB3350CP
Power Supply (PSU): CVB32005
PWM Power: AP3105NV (PWM SOT23-6 GKO)
MainBoard: CV9202H-TPW
IC MainBoard: SPI Flash: 25Q64BV
Tuner: ST03WS-2A-E
TF-LED29S30T2 Specifications
TELEFUNKEN TF-LED29S30T2
General recommendations for TV LCD LED repair
Possible manifestations of malfunctions
- TELEFUNKEN TF-LED29S30T2 TV does not turn on. There are no signs of operability. The indicators on the front panel do not light up or blink, and does not respond to the remote control and control buttons.
Often in such cases, the CVB32005 power supply module is faulty. Then you should measure its output voltages and, in their absence, we recommend checking the serviceability of the power switches and rectifier diodes of the converters for a possible short circuit.
In the event of breakdowns in the secondary circuits, the converter can operate in an emergency mode in a short circuit without output voltages, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse is usually cut off, and sometimes the current sensor in the source of the key.
Breakdown of Mos-Fet keys used in switching power supplies is often caused by malfunctions of other elements, for example, supply, frequency setting, damper ... as well as elements of Negative Feedback Stabilization. The PWM microcircuit (PWM) AP3105NV (PWM SOT23-6 GKO) can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no picture, there is sound, it reacts to the remote control, the channels are switched. In some cases, the image appears when turned on and disappears immediately.
The malfunction in most of such cases is found in the nodes and elements of the LED panel backlighting. The reason for this may be an open circuit in the LED circuit, or a problem in stabilizing their power supply.
To check the health of the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N transition test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black one to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. The serviceability of the PN junction of the Zener diode indirectly indicates the serviceability of the LED-a
- The indicator blinks or is on constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the CV9202H-TPW motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the serviceability of its elements - SPI Flash: 25Q64BV which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its pins with the board (indicated by heating)
The malfunction of the ST03WS-2A-E tuner is established after checking the software and all supply voltages at its terminals. The tuner data exchange with the processor via the I2C bus can be monitored with an oscilloscope.
Users and owners of TVs should remember that attempts to self-repair the TELEFUNKEN TF-LED29S30T2 TV without the appropriate qualifications and the necessary experience can lead to serious negative consequences!
Additional MainBoard Repair
The appearance of the MainBoard CV9202H-TPW is shown in the figure below:
CV9202H-TPW
AKAI LEA-39J29P (Panel HF390BGA-C1), BBK 32LEM-1001/T2C (Panel CX315DLEDM), DNS M39DM8 (Panel V390HJ1-P02 Rev C1), ERISSON 32LEE17 (Panel 720p HD 1366x768), FUSION FLTV-32T22 (Panel ST3151A05), FUSION FLTV-28T20 (Panel LCM-SM275TK301 (D0306)), FUSION FLTV-28T22 (Panel TH280L321-04), FUSION FLTV-32T23 (Panel ST3151A04-1 / Ver.2.4), FUSION FLTV-32T20 (Panel V320BK1-PS5 Rev.C7), TELEFUNKEN TF-LED40S28T2 (Panel CX400DLEDM), TELEFUNKEN TF-LED29S30T2 (Panel V290BJ1-XC01 CX290DLEDM), TELEFUNKEN TF-LED40S6T2 (Panel CX400DLEDM).
External view of the power supply
Main features of the TELEFUNKEN TF-LED29S30T2 device:
Installed matrix (LED-panel) V290BJ1-XC01 CX290DLEDM.
A converter combined with a power supply is used to power the backlight LEDs, and is controlled by the OB3350CP PWM controller.
The formation of the necessary supply voltages for all nodes of the TELEFUNKEN TF-LED29S30T2 TV is carried out by the CVB32005 power module, or its analogs using AP3105NV microcircuits (PWM SOT23-6 GKO).
MainBoard - the main board (motherboard) is a CV9202H-TPW module, using SPI Flash chips: 25Q64BV and others.
The ST03WS-2A-E tuner provides reception of television programs and tuning to channels.
PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages
In
the circuitry of modern switching power supplies (SMPS), PWM
controllers made in small-sized planar packages with six terminals have
gained wide popularity. The enclosure type designation can be SOT-23-6,
SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the
pins are shown in the figure below. In this case, the code marking
LD7530A is shown on the left fragment of the picture.
Pin assignment:
1 - GND. (Common wire).
2
- FB. (FeedBack - Feedback). Input for controlling the duration of
pulses with a signal from the output voltage. Sometimes it can be
labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC -
Depending on the type of microcircuit, it can be used for a
frequency-setting RC circuit (RI / RT / CT), or for organizing
protection, as an input of a PWM trip comparator at a threshold value at
its input, specified in the document. In some types of microcircuits,
this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.
Functionally,
these regulators work on the principle of the previously popular xx384x
PWM microcircuits, which have proven themselves well in terms of
reliability and stability.
Some difficulties often arise when
replacing or choosing an analog for such PWM regulators due to the use
of code markings in the designation of the type of microcircuits. The
situation is complicated by a large number of component manufacturers
who do not always provide documentation to the mass access, just as not
all manufacturers of finished devices supply repair service centers with
diagrams, so repairmen often have to study real circuit solutions by
installed components and wiring connections directly on the board.
In
practice, PWM microcircuits and the marking code EAxxx and Eaxxx are
often found. Official documentation for them was not found in the public
domain, but discussions on the forums and pieces of pictures from PDF
from System General, which publishes them as SG6848T and SG6848T2, have
survived. The drawing is here placed left .
For the attention of the masters, here below are PDF datasheet tables
compiled from information available on the Internet and PDF documents
for the selection of analogues types when replacing the most common
six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP),
pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| SG6849 | SG684965TZ | Fairchild / ON Semi | BBxx |
| SG6849 | SG6849-65T, SG6849-65TZ | System General | MBxx EBxx |
| SGP400 | SGP400TZ | System General | AAKxx |
PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.
When
applying the PWM listed below, the frequency should be set with the RT
(RI) resistor from pin 3 to ground. Usually its nominal value is chosen
95-100 kOhm for a frequency of 65-100 KHz. For more details, see the
here below attached documentation. PDF files are packed in RAR.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3103A | AP3103AKTR-G1 | Diodes Incorporated | GHL |
| AP8263 | AP8263E6R, A8263E6VR | AiT Semiconductor | S1xx |
| AT3263 | AT3263S6 | ATC Technology | 3263 |
| CR6848 | CR6848S | Chip-Rail | 848H16 |
| CR6850 | CR6850S | Chip-Rail | 850xx |
| CR6851 | CR6851S | Chip-Rail | 851xx |
| FAN6602R | FAN6602RM6X | Fairchild / ON Semi | ACCxx |
| FS6830 | FS6830 | FirstSemi | |
| GR8830 | GR8830CG | Grenergy | 30xx |
| GR8836 | GR8836C, GR8836CG | Grenergy | 36xx |
| H6849 | H6849NF | HI-SINCERITY | |
| H6850 | H6850NF | HI-SINCERITY | |
| HT2263 | HT2263MP | HOT-CHIP | 63xxx |
| KP201 | Kiwi Instruments | ||
| LD5530 | LD5530GL LD5530R | Leadtrand | xxt30 xxt30R |
| LD7531 | LD7531GL, LD7531PL | Leadtrend | xxP31 |
| LD7531A | LD7531AGL | Leadtrend | xxP31A |
| LD7535/A | LD7535BL, LD7535GL, LD7535ABL, LD7535AGL | Leadtrend | xxP35-xxx35A |
| LD7550 | LD7550BL, LD7550IL | Leadtrend | xxP50 |
| LD7550B | LD7550BBL, LD7550BIL | Leadtrend | xxP50B |
| LD7551 | LD7551BL/IL | Leadtrend | xxP51 |
| LD7551C | LD7551CGL | Leadtrend | xxP51C |
| NX1049 | XN1049TP | Xian-Innuovo | 49xxx |
| OB2262 | OB2262MP | On-Bright-Electronics | 62xx |
| OB2263 | OB2263MP | On-Bright-Electronics | 63xx |
| PT4201 | PT4201E23F | Powtech | 4201 |
| R7731 | R7731GE/PE | Richtek | 0Q= |
| R7731A | R7731AGE | Richtek | IDP=xx |
| SD4870 | SD4870TR | Silan Microelectronics | 4870 |
| SF1530 | SF1530LGT | SiFirst | 30xxx |
| SG5701 | SG5701TZ | System General | AAExx |
| SG6848 | SG6848T, SG6848T1, SG6848TZ1, SG6848T2 | Fairchild / ON Semi | AAHxx EAxxx |
| SG6858 | SG6858TZ | Fairchild / ON Semi | AAIxx |
| SG6859A | SG6859ATZ, SG6859ATY | Fairchild / ON Semi | AAJFxx |
| SG6859 | SG6859TZ | Fairchild / ON Semi | AAJMxx |
| SG6860 | SG6860TY | Fairchild | AAQxx |
| SP6850 | SP6850S26RG | Sporton Lab | 850xx |
| SP6853 | SP6853S26RGB, SP6853S26RG | Sporton Lab | 853xx |
| SW2263 | SW2263MP | SamWin | |
| UC3863/G | UC3863G-AG6-R | Unisonic Technologies Co | U863 U863G |
| XN1049 | XN1049, XN1049TP | Innuovo Microelectronics | 49 xxx |
PWM controllers that use pin 3 differently.
When
using the following PWM (PWM controllers), you should pay attention to
pin 3, which can be used to organize protection - thermal or from
overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3105/V/L/R | AP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1 | Diodes Incorporated | GHN GHO GHP GHQ |
| AP3105NA/NV/NL/NR | AP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1 | Diodes Incorporated | GKN GKO GKP GKQ |
| AP3125A/V/L/R | AP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1 | Diodes Incorporated | GLS GLU GNB GNC |
| AP3125B | AP3125BKTR-G1 | Diodes Incorporated | GLV |
| AP3125HA/HB | AP3125HAKTR-G1, AP3125HBKTR-G1 | Diodes Incorporated | GNP GNQ |
| AP31261 | AP31261KTR-G1 | Diodes Incorporated | GPE |
| AP3127/H | AP3127KTR-G1, AP3127HKTR-G1 | Diodes Incorporated | GPH GSH |
| AP3301 | AP3301K6TR-G1 | Diodes Incorporated | GTC |
| FAN6862 | FAN6862TY | Fairchild / ON Semi | ABDxx |
| FAN6863 | FAN6863TY, FAN6863LTY, FAN6863RTY | Fairchild / ON Semi | ABRxx |
| HT2273 | HT2273TP | HOT-CHIP | 73xxx |
| LD7510/J | LD7510GL, LD7510JGL | Leadtrend | xxP10 xxP10J |
| LD7530/A | LD7530PL, LD7530GL, LD7530APL, LD7530AGL | Leadtrend | xxP30 xxxP30A |
| LD7532 | LD7532GL | Leadtrend | xxP32 |
| LD7532A | LD7532AGL | Leadtrend | xxP32A |
| LD7532H | LD7532HGL | Leadtrend | xxP32H |
| LD7533 | LD7533GL | Leadtrend | xxP33 |
| LD7536 | LD7536GL | Leadtrend | xxP36 |
| LD7536R | LD7536RGL | Leadtrend | xxP36R |
| LD7537R | LD7537RGL | Leadtrend | xxP37R |
| LD7539C GL | LD7539C GL | Leadtrend | xxP39C |
| ME8204 | ME8204M6G | MicrOne | ME8204xx |
| NCP1250 | NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1G | ON Semiconductor | 25xxxx |
| NCP1251 | NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1G | ON Semiconductor | 5xxxxx |
| OB2273 | OB2273MP | On-Bright-Electronics | 73xx |
| R7735 | R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGE | Richtek | |
| UC3873/G | UC3873-AG6-R, UC3873G-AG6-R | Unisonic Technologies | U873 U873G |
TV TELEFUNKEN TF-LED29S30T2 with LCD V290BJ1-XC01, diagonal size 29 "(74 cm) 16: 9. The brightness of the screen 230 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 3000 : 1. The LED panel of this TV is equipped with Edge LED, which can display high quality HD images at a resolution of 1366x768 pixels in 720p (HD Ready). The input high frequency or video signal can be processed in analog PAL systems , SECAM, NTSC Graphic processing and digital signal shaping takes place in 480i, 480p, 576i, 576p, 720p, 1080i, 1080p standards Supported multimedia file formats: MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
Speaker power of 16 W (2x8 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, VGA, HDMI x3, USB. A headphone output is provided. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The digital tuner is capable of receiving TV channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Overall dimensions: 671x409x180 mm.
TV weight: 4.8 kg.
Attention! Panel V290BJ1-XC01 CX290DLEDM LED TV TELEFUNKEN TF-LED29S30T2 is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV non-repairable.