Technical description and composition of the PHILIPS 32PFT4132 TV, panel type and modules used. The composition of the modules.PHILIPS LED
Model: 32PFT4132 / 60
Chassis / Version: TPN17.1E
Panel: TPT315B5-EUJFFE
LED backlight: LBM320M0701-LD-1 (5)
LED driver (backlight): integrated into PSU
PWM LED driver: PF7708BS
MOSFET LED driver: MTBA5N10J3
Power Supply (PSU): 715G7734-P02-005-002H
PWM Power: PWM SOT23-6 PF6005A
MOSFET Power: TK6A65D
MainBoard: 715G8659-M01-000-004Y
IC MainBoard: CPU: NT72461, NAND: W29N01HVSINF, AUDIO: TAS5753MD
Tuner: TDSY-G430D
Specifications 32PFT4132
PHILIPS 32PFT4132
General recommendations for TV LCD LED repair
Possible manifestations of defects
- PHILIPS 32PFT4132 TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up or flash.
In such cases, you should start looking for a fault in the 715G7734-P02-005-002H power supply circuits. It is necessary to measure its output supply voltages, and in their absence, check the serviceability of the power switches (TK6A65D) of the converters and rectifier diodes for the probability of breakdown in semiconductor PN junctions.
In case of breakdowns in the secondary circuits, the converter, as a rule, can operate in an emergency mode in a short circuit mode, and in case of a short circuit in the power elements of the primary circuit, the mains fuse usually breaks.
Breakdown of Mos-Fet switches used in switching power supplies is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency setting or damper circuits, as well as in negative feedback stabilization. PWM microcircuits (PWM) PWM SOT23-6 PF6005A are usually checked by replacing them with new ones, or knowingly working.
- There is no image, there is sound, it reacts to the remote control. Or the image may appear for a second when turned on and disappear immediately.
Usually, in such cases, a malfunction is detected in the LED panel backlight nodes. Usually the cause of the malfunction is in the breakage of the LEDs, or in the connectors of the LED strips, but sometimes the LED driver is also faulty.
It should be remembered that it is not possible to determine an open circuit in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then you need to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow opening the LED in the forward direction or dual LEds are used, then the PN transition of the emergency zener diode can indirectly serve as an indicator of serviceability. In the event of a malfunction of the LED-a, the PN-junction of the zener diode will either be cut off or broken into the K / Z.
- The indicator blinks or is on constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the 715G8659-M01-000-004Y motherboard should begin with checking the stabilizers and power converters required to power the microcircuits and matrix. If necessary, you should update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the serviceability of its elements - CPU: NT72461, AUDIO: TAS5753MD which may need to be replaced with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its pins with the board (detected by warming up).
If PHILIPS 32PFT4132 has no picture, but there is sound, often the TPT315B5-EUJFFE display backlight simply does not work. Moreover, in LED TVs, the LEDs inside the panel usually fail, less often the LED driver.
In such cases, you can see a barely noticeable image when the external light hits the screen.
Replacing the LEDs requires disassembling the TPT315B5-EUJFFE LCD panel - a process that requires experience and qualifications from the master. We do not recommend doing such work on your own to the owners of TVs and craftsmen who do not have experience in repairing LCD panels
If there is no image, and the backlight is on, the screen becomes slightly lighter when turned on, and in an open TV you can see light through the holes in the panel case.
In this case, the panel may also be faulty - damage to strips, loops, for example, as a result of moisture ingress after unsuccessful washing of the screen, the T-CON (Timing Controller) board may be faulty. But often the main board MainBoard 715G8659-M01-000-004Y also turns out to be faulty, a software failure is also possible.
Then, first of all, you need to check the panel supply voltage, the fuses on the T-CON board, as well as the supply and reference voltages of the column and line drivers - VGH, VGL, Vcom.
If these measurements are within the normal range, it is necessary to use an oscilloscope to trace the passage of LVDS signals from MainBoard 715G8659-M01-000-004Y, as well as synchronization signals to loops with drivers.
Flooded or unsuccessfully washed screens of LED TVs can be restored, in about half of the cases, usually if significant damage has not formed in the loops and panel strips.
panelˈpanl
If there is no reception of television channels, but the TV is working properly from external devices, first of all, you need to check the supply voltage of the TDSY-G430D tuner and update the software. I2C communication pulses must be monitored with an oscilloscope.
Remember! Attempts to self-repair the PHILIPS 32PFT4132 TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
DOWNLOAD SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> Chassis TPN17.1E EU for models 22PFS4232/12, 43PFT4112/05, 22PFT4232/12, 43PFT4112/12, 32PFS4132/12, 24PFS4032/12, 32PFT4132/05, 24PFT4032/12, 32PFT4132/12, 24PFT4032/60, 32PFT4132/60, 24PHS4032/12, 32PHS4132/12, 24PHT4032/05, 32PHT4132/05, 24PHT4032/12, 32PHT4132/12, 24PHT4032/60, 32PHT4132/60, 32PHS4032/12, 43PFS4132/12, 32PHT4032/12, 43PFT4132/05, 32PHT4032/60, 43PFT4132/12, 22PFS4022/12, 43PFT4132/60, 22PFT4022/05, 49PFS4132/12, 22PFT4022/12, 49PFT4132/12, 22PFT4022/60, 32PHS4112/12, 24PFS4022/12, 32PHT4112/05, 24PFT4022/12, 32PHT4112/12, 24PFT4022/60, 39PHS4112/12, 24PHS4022/12, 39PHT4112/05, 24PHT4022/05, 39PHT4112/12, 24PHT4022/12, 43PFS4112/12.
Additional MainBoard RepairThe appearance of the MainBoard 715G8659-M01-000-004Y is shown in the figure below:
715G8659-M01-000-004Y
External view of the power supply
The main features of the PHILIPS 32PFT4132 device:
Installed matrix (LED panel) TPT315B5-EUJFFE.
A converter combined with a power supply is used to power the backlight LEDs, it is controlled by a PF7708BS PWM controller. The keys of the MTBA5N10J3 type are used as power elements of the LED driver.
The formation of the necessary supply voltages for all nodes of the PHILIPS 32PFT4132 TV is carried out by the 715G7734-P02-005-002H power module, or its analogs using PWM SOT23-6 PF6005A microcircuits and TK6A65D power switches.
MainBoard - the main board (motherboard) is a 715G8659-M01-000-004Y module, using CPU chips: NT72461, NAND: W29N01HVSINF, AUDIO: TAS5753MD and others.
The TDSY-G430D tuner provides reception of television programs and tuning to channels.
PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages
In
the circuitry of modern switching power supplies (SMPS), PWM
controllers made in small-sized planar packages with six terminals have
gained wide popularity. The enclosure type designation can be SOT-23-6,
SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the
pins are shown in the figure below. In this case, the code marking
LD7530A is shown on the left fragment of the picture.
Pin assignment:
1 - GND. (Common wire).
2
- FB. (FeedBack - Feedback). Input for controlling the duration of
pulses with a signal from the output voltage. Sometimes it can be
labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC -
Depending on the type of microcircuit, it can be used for a
frequency-setting RC circuit (RI / RT / CT), or for organizing
protection, as an input of a PWM trip comparator at a threshold value at
its input, specified in the document. In some types of microcircuits,
this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.
Functionally,
these regulators work on the principle of the previously popular xx384x
PWM microcircuits, which have proven themselves well in terms of
reliability and stability.
Some difficulties often arise when
replacing or choosing an analog for such PWM regulators due to the use
of code markings in the designation of the type of microcircuits. The
situation is complicated by a large number of component manufacturers
who do not always provide documentation to the mass access, just as not
all manufacturers of finished devices supply repair service centers with
diagrams, so repairmen often have to study real circuit solutions by
installed components and wiring connections directly on the board.
In
practice, PWM microcircuits and the marking code EAxxx and Eaxxx are
often found. Official documentation for them was not found in the public
domain, but discussions on the forums and pieces of pictures from PDF
from System General, which publishes them as SG6848T and SG6848T2, have
survived. The drawing is here placed left .
For the attention of the masters, here below are PDF datasheet tables
compiled from information available on the Internet and PDF documents
for the selection of analogues types when replacing the most common
six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP),
pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| SG6849 | SG684965TZ | Fairchild / ON Semi | BBxx |
| SG6849 | SG6849-65T, SG6849-65TZ | System General | MBxx EBxx |
| SGP400 | SGP400TZ | System General | AAKxx |
PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.
When
applying the PWM listed below, the frequency should be set with the RT
(RI) resistor from pin 3 to ground. Usually its nominal value is chosen
95-100 kOhm for a frequency of 65-100 KHz. For more details, see the
here below attached documentation. PDF files are packed in RAR.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3103A | AP3103AKTR-G1 | Diodes Incorporated | GHL |
| AP8263 | AP8263E6R, A8263E6VR | AiT Semiconductor | S1xx |
| AT3263 | AT3263S6 | ATC Technology | 3263 |
| CR6848 | CR6848S | Chip-Rail | 848H16 |
| CR6850 | CR6850S | Chip-Rail | 850xx |
| CR6851 | CR6851S | Chip-Rail | 851xx |
| FAN6602R | FAN6602RM6X | Fairchild / ON Semi | ACCxx |
| FS6830 | FS6830 | FirstSemi | |
| GR8830 | GR8830CG | Grenergy | 30xx |
| GR8836 | GR8836C, GR8836CG | Grenergy | 36xx |
| H6849 | H6849NF | HI-SINCERITY | |
| H6850 | H6850NF | HI-SINCERITY | |
| HT2263 | HT2263MP | HOT-CHIP | 63xxx |
| KP201 | Kiwi Instruments | ||
| LD5530 | LD5530GL LD5530R | Leadtrand | xxt30 xxt30R |
| LD7531 | LD7531GL, LD7531PL | Leadtrend | xxP31 |
| LD7531A | LD7531AGL | Leadtrend | xxP31A |
| LD7535/A | LD7535BL, LD7535GL, LD7535ABL, LD7535AGL | Leadtrend | xxP35-xxx35A |
| LD7550 | LD7550BL, LD7550IL | Leadtrend | xxP50 |
| LD7550B | LD7550BBL, LD7550BIL | Leadtrend | xxP50B |
| LD7551 | LD7551BL/IL | Leadtrend | xxP51 |
| LD7551C | LD7551CGL | Leadtrend | xxP51C |
| NX1049 | XN1049TP | Xian-Innuovo | 49xxx |
| OB2262 | OB2262MP | On-Bright-Electronics | 62xx |
| OB2263 | OB2263MP | On-Bright-Electronics | 63xx |
| PT4201 | PT4201E23F | Powtech | 4201 |
| R7731 | R7731GE/PE | Richtek | 0Q= |
| R7731A | R7731AGE | Richtek | IDP=xx |
| SD4870 | SD4870TR | Silan Microelectronics | 4870 |
| SF1530 | SF1530LGT | SiFirst | 30xxx |
| SG5701 | SG5701TZ | System General | AAExx |
| SG6848 | SG6848T, SG6848T1, SG6848TZ1, SG6848T2 | Fairchild / ON Semi | AAHxx EAxxx |
| SG6858 | SG6858TZ | Fairchild / ON Semi | AAIxx |
| SG6859A | SG6859ATZ, SG6859ATY | Fairchild / ON Semi | AAJFxx |
| SG6859 | SG6859TZ | Fairchild / ON Semi | AAJMxx |
| SG6860 | SG6860TY | Fairchild | AAQxx |
| SP6850 | SP6850S26RG | Sporton Lab | 850xx |
| SP6853 | SP6853S26RGB, SP6853S26RG | Sporton Lab | 853xx |
| SW2263 | SW2263MP | SamWin | |
| UC3863/G | UC3863G-AG6-R | Unisonic Technologies Co | U863 U863G |
| XN1049 | XN1049, XN1049TP | Innuovo Microelectronics | 49 xxx |
PWM controllers that use pin 3 differently.
When
using the following PWM (PWM controllers), you should pay attention to
pin 3, which can be used to organize protection - thermal or from
overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3105/V/L/R | AP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1 | Diodes Incorporated | GHN GHO GHP GHQ |
| AP3105NA/NV/NL/NR | AP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1 | Diodes Incorporated | GKN GKO GKP GKQ |
| AP3125A/V/L/R | AP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1 | Diodes Incorporated | GLS GLU GNB GNC |
| AP3125B | AP3125BKTR-G1 | Diodes Incorporated | GLV |
| AP3125HA/HB | AP3125HAKTR-G1, AP3125HBKTR-G1 | Diodes Incorporated | GNP GNQ |
| AP31261 | AP31261KTR-G1 | Diodes Incorporated | GPE |
| AP3127/H | AP3127KTR-G1, AP3127HKTR-G1 | Diodes Incorporated | GPH GSH |
| AP3301 | AP3301K6TR-G1 | Diodes Incorporated | GTC |
| FAN6862 | FAN6862TY | Fairchild / ON Semi | ABDxx |
| FAN6863 | FAN6863TY, FAN6863LTY, FAN6863RTY | Fairchild / ON Semi | ABRxx |
| HT2273 | HT2273TP | HOT-CHIP | 73xxx |
| LD7510/J | LD7510GL, LD7510JGL | Leadtrend | xxP10 xxP10J |
| LD7530/A | LD7530PL, LD7530GL, LD7530APL, LD7530AGL | Leadtrend | xxP30 xxxP30A |
| LD7532 | LD7532GL | Leadtrend | xxP32 |
| LD7532A | LD7532AGL | Leadtrend | xxP32A |
| LD7532H | LD7532HGL | Leadtrend | xxP32H |
| LD7533 | LD7533GL | Leadtrend | xxP33 |
| LD7536 | LD7536GL | Leadtrend | xxP36 |
| LD7536R | LD7536RGL | Leadtrend | xxP36R |
| LD7537R | LD7537RGL | Leadtrend | xxP37R |
| LD7539C GL | LD7539C GL | Leadtrend | xxP39C |
| ME8204 | ME8204M6G | MicrOne | ME8204xx |
| NCP1250 | NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1G | ON Semiconductor | 25xxxx |
| NCP1251 | NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1G | ON Semiconductor | 5xxxxx |
| OB2273 | OB2273MP | On-Bright-Electronics | 73xx |
| R7735 | R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGE | Richtek | |
| UC3873/G | UC3873-AG6-R, UC3873G-AG6-R | Unisonic Technologies | U873 U873G |
Updating software (firmware, firmware).Version: 2.230, zip file, 41.7 MB, published February 7, 2020 version.Documentation:ERP Power consumption declaration PDF file, 192.5 kB, published July 25, 2017Quick start guide PDF file, 1.6 MB, published September 1, 2017Brochure Version: 3.0.1, PDF file, 438.8 kB, published July 19, 2019User manual PDF file, 2.9 MB, published February 21, 2018Files can be downloaded from the manufacturer's website for model 32PFT4132 / 60.
PHILIPS 32PFT4132 TV with LCD TPT315B5-EUJFFE, diagonal size 31.5 "(80 cm) 16: 9. The required brightness of the screen of 280 cd / m2 is provided by LED backlighting. The LCD panel is backlit from Direct LED LEDs.It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
TPT315B5-EUJFFE sensor and MainBoard 715G8659-M01-000-004Y software provide viewing of broadcasts and movies in high quality HD at a resolution of 1920x1080 pixels in graphics resolution at 1080p (Full HD). Supported media file formats: MP3, WMA, MPEG4, HEVC (H.265), MKV, JPEG.
Speaker power 16 W (2x8 W) is provided by two speakers. Uses NICAM stereo processing system and Sound Surround function.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), HDMI x2, USB. A headphone output is provided.
The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
The TV uses a 715G7734-P02-005-002H power supply.
Dimensions: with stand 727x479x185 mm, without stand 727x425x82 mm.
TV weight: with stand: 4.85 kg, without stand: 4.8 kg.
Attention! Panel TPT315B5-EUJFFE LED TV PHILIPS 32PFT4132 is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!