Technical description and composition of the SAMSUNG UE32C6200 TV, panel type and modules used. The composition of the modules.SAMSUNG LED
Model: UE32C6200
Chassis / Version: N96A
Panel: LTF320HF02
LED driver (backlight): integrated into PSU
PWM LED driver: SELC2010
Power Supply (PSU): BN44-00355A
PWM Power: ICE3BR1765J (Standby), UCC25600 (PWM 8pin)
MOSFET Power: FQPF9N50CF
MainBoard: BN41-01444B BN94-03781A
IC MainBoard: SDP92, WT61P802, 24C02, 24C256, KFG8GH6U4M
Tuner: BN40-00187A
UE32C6200 Specifications
SAMSUNG UE32C6200
General recommendations for TV LCD LED repair
Possible manifestations of defects
- SAMSUNG UE32C6200 TV does not turn on at all. Control lamps do not light up or blink. The TV on the remote control and control panel buttons does not respond.
In such cases, the fault should be looked for primarily in the BN44-00355A power supply module. Then you should measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of the power switches (FQPF9N50CF) and rectifier diodes of the converters for a possible short circuit.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually operate in an emergency mode in a short-circuit mode, and in case of a short circuit in the power elements of the primary circuit, the mains fuse often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements, which can disable it in key mode, or provoke an excess of the maximum current or voltage values. These can be circuits supplying the PWM controller, damper or frequency setting circuits, or OOS (negative feedback) elements in the stabilization circuit. PWM controllers (PWM) ICE3BR1765J (Standby), UCC25600 (PWM 8pin), in the absence of external damage and short circuit between the terminals, are checked by replacing them with known good ones.
- There is no picture, but there is sound and all other TV functions are working. The image sometimes appears for a second immediately after switching on and disappears.
As a rule, in this case, the backlight of the LED panel is faulty. Most often, the reason for this is a break in the LEDs, or poor contact in the connectors of the brackets, less often the LED driver may be faulty.
It should be remembered that it is not possible to determine an open circuit in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then you need to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow opening the LED in the forward direction or dual LEds are used, then the PN transition of the emergency zener diode can indirectly serve as an indicator of serviceability. In the event of a malfunction of the LED-a, the PN-junction of the Zener diode will either be cut off, or broken through in the SC.
- The indicator blinks or is on constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-01444B motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Complicated repair of MB (SSB) board is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace elements SDP92, WT61P802, 24C02, 24C256, KFG8GH6U4M. Malfunctions in BGA chips are usually easy to detect by warm-up.
Before changing the tuner BN40-00187A, if it is not possible to tune to television channels, you should make sure that there are supply voltages, which must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be monitored with an oscilloscope.
If SAMSUNG UE32C6200 has no picture, but there is sound, often the LTF320HF02 display backlight simply does not work. Moreover, in LED TVs, the LEDs inside the panel usually fail, less often the LED driver.
In such cases, you can see a barely noticeable image with a successful hit of external light on the screen.
Replacing the LEDs requires disassembling the LTF320HF02 LCD panel, a process that requires experience and qualifications from the technician. We do not recommend doing such work on your own to the owners of TVs and craftsmen who do not have experience in repairing LCD panels
If there is no image, and the backlight is on, the screen becomes slightly lighter when turned on, and in an open TV you can see the light through the holes in the panel case.
In this case, the panel may also be faulty - damage to the strips, loops, for example, as a result of moisture ingress after unsuccessful washing of the screen, the T-CON (Timing Controller) board may be faulty. But the main board MainBoard BN41-01444B often turns out to be faulty, a software failure is also possible.
Then, first of all, you need to check the panel supply voltage, the fuses on the T-CON board, as well as the supply and reference voltages of the column and line drivers - VGH, VGL, Vcom.
If these measurements are within normal limits, it is necessary to trace the passage of LVDS signals from MainBoard BN41-01444B, as well as synchronization signals to the loops with drivers, with an oscilloscope.
Flooded or unsuccessfully washed screens of LED TVs can be restored, in about half of the cases, usually if significant damage has not formed in the loops and panel strips.
Attention to users! Self-repair of the SAMSUNG UE32C6200 TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
Additional MainBoard Repair
The appearance of the MainBoard BN41-01444B is shown in the figure below:
BN41-01444B
BN41-01444B can be used in TVs:
SAMSUNG UE32C6000RW UE32C6000 (Panel LTF320HF02), SAMSUNG UE32C6700 UE32C6700US (Panel LTF320HF02 (BN07-00858A)), SAMSUNG UE37C6000 UE37C6000RW (Panel T370FBE2-DA), SAMSUNG UE46C6000 UE46C6000RW (Panel LTF460HJ03).
External view of the power supply
Main features of SAMSUNG UE32C6200 device:
Installed matrix (LED panel) LTF320HF02.
To power the backlight LEDs, a converter combined with a power supply is used, controlled by the SELC2010 PWM controller.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE32C6200 TV is carried out by the BN44-00355A power module, or its analogs using ICE3BR1765J (Standby), UCC25600 (PWM 8pin) chips and FQPF9N50CF power switches.
MainBoard - the main board (motherboard) is a BN41-01444B, using microcircuits SDP92, WT61P802, 24C02, 24C256, KFG8GH6U4M and others.
Tuner BN40-00187A provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTF320HF02
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1920x1080, FHD
Display Mode: S-PVA, Normally Black, Transmissive
Display Colors: 16.7M (8-bit)
Frequency: 120Hz
Lamp Type: WLED.
For model UE32C6200RSXZG from the manufacturer there are files to download:Latest firmware updates (latest firmwares):
File type File name Version Date Size
Datei Upgrade (USB) T-VAL6DEUC_1017.0.exe T-VAL6DEUC-1017.0 05/04/2012 34.33 Mb
Datei Upgrade (USB) T-MSX6DEUC_2001.0.exe T-MSX6DEUC-2001.0 04.05.2012 46.58 Mb
User Manuals and Instructions:
File type File name Version Date Size
Bedienungsanleitung BN68-02694F-00L04-0414.pdf 1.0 26.05.2010 33.03 Mb
Stromverbrauch Handbuch 6Series_Power_consumption_LED_TV.pdf 1.0 06.09.2010 0.17 Mb
Files can be downloaded from the manufacturer's website for the UE32C6200RSXZG model.
SAMSUNG UE32C6200 TV with LCD display LTF320HF02, 32 "(81 cm) 16: 9 format diagonally. This model uses a panel with edge LED backlighting - Edge LED.
The LTF320HF02 sensor and MainBoard BN41-01444B software allow viewing of broadcasts and movies in high quality HD at a resolution of 1920x1080 pixels in graphics resolution in 1080p (Full HD). The input analog video signal is decoded in PAL, SECAM, NTSC systems. Graphic processing of a digital signal is performed in the 480i, 480p, 576i, 576p, 720p, 1080i, 1080p standards. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
Sound speaker power 20 W (2x10 W). The NICAM stereo audio processing system and the Sound Surround function are used.
Communication with other devices via an external interface is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, RGB, VGA, HDMI x4, USB x2, Ethernet (RJ-45). A headphone jack is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is provided. This interface supports standard resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
The digital tuner can receive television channels in the DVB-T MPEG4, DVB-C, DVB-S2 standards.
The power consumed when operating from the network is 120 W. Power supply BN44-00355A.
Dimensions: with stand 774x542x242 mm, without stand 774x479x30 mm.
TV weight: with stand: 11.1 kg, without stand: 8.3 kg.
Attention! SAMSUNG UE32C6200 LED TV panel LTF320HF02 is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.