Technical description and composition of the SONY KDL-32WE613 TV, panel type and modules used. The composition of the modules.
SONY LED
Model: KDL-32WE613
Chassis / Version: MAIN BLM SONY
Panel: IS7S320HN001
LED backlight: 4-596-427 17Y 32_7020_32_REV01_170316
LED driver (backlight): 1-981-455-11 (173638611)
PWM LED driver: BD9423EFV
MOSFET LED driver: D2910
Power Supply (PSU): Adapter 19.5V AC / D ACDP-060L01
MainBoard: 1-981-541-23 (173641423)
IC MainBoard: CPU: MEDIATEK
Tuner: DE251ZP
KDL-32WE613 Specifications
SONY KDL-32WE613
General recommendations for TV LCD LED repair
Possible manifestations of defects
- TV SONY KDL-32WE613 does not turn on and does not give any signs of turning on, does not respond to control buttons and to the remote control.
In such cases, you should start looking for a fault in the adapter power supply circuits.
The TV model under consideration is equipped with an external power supply Adapter 19.5V AC / D ACDP-060L01, the repair of which is not always advisable, but opening it and eliminating the simplest typical defects typical of modern SMPS is usually not difficult for a qualified technician. It is necessary to measure the output voltages in its secondary circuits, and if they are completely absent, the serviceability of the power switches and rectifier diodes should be checked for a possible breakdown (short circuit).
In case of breakdowns in the secondary circuits of the converter, it can usually work in an emergency mode in a short circuit mode, and with a short circuit in the power elements of the primary circuit, the mains fuse or current sensor in the source of the key is most often cut off.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can disable it in the key mode, or create an excess of the maximum permissible key parameters. These can be elements supplying a PWM regulator, frequency setting or damper circuits, or elements of negative feedback in the stabilization circuit. PWM controllers, in the absence of visible damage or outright short circuits between the terminals, are checked by replacing them with new ones, or knowingly working properly.
- No picture, sound, all other TV functions are working. When turned on, the image may sometimes appear for a second.
A malfunction is usually in these cases most likely in the backlight units of the display matrix. The reason may be found in a malfunction of the LEDs, in a violation of the contact connections of the LED strips 4-596-427 17Y 32_7020_32_REV01_170316, or in providing their power supply (LED driver).
It is impossible to check the LED bars for a break without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts is required, and ideally a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters tend to light one 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as an indicator of serviceability. In faulty LEDs, the zener diode will either be cut off, or pierced in the K / Z.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals the standby mode.
Repair or diagnostics of the 1-981-541-23 motherboard should begin with checking the stabilizers and power converters required to power the microcircuits and matrix. If necessary, you should update or replace the software (software). In some cases, to repair the MB (SSB) board, it may be necessary to replace the chips - CPU: MEDIATEK with new or known good ones. In cases where BGA technologies are used, defects are usually localized by heating.
Before replacing the DE251ZP tuner, if there is no tuning to the channels, you must first check the software and supply voltage at its outputs. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Owners and users of the SONY KDL-32WE613 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
Additional MainBoard Repair
The appearance of MainBoard 1-981-541-23 is shown in the figure below:
1-981-541-23
Main features of the SONY KDL-32WE613 device:
Installed matrix (LED panel) IS7S320HN001.
The LED driver 1-981-455-11 is used to power the backlight LEDs, it is controlled by the PWM controller BD9423EFV. D2910 keys are used as power elements of the LED driver.
An external adapter 19.5V AC / D ACDP-060L01 is used to power all the internal components of the SONY KDL-32WE613 TV.
MainBoard - the main board (motherboard) is a 1-981-541-23 module, using CPU chips: MEDIATEK and others.
The DE251ZP tuner provides reception of television programs and tuning to channels.
Instructions and updates
Firmware update to v8.582:
File sony_tvupdate_2017_8582_enf_auth.zip, version 8.582 dated 22.06.2020 (290 409 452 bytes).
For models: KDL49WE753, KDL43WE753, KDL49WE663, KDL49WE665, KDL40WE663, KDL32WE613, KDL49WE755, KDL43WE755, KDL40WE665, KDL32WE615, KDL49WE750, KDL43WE750, KDL49WE660, KDL40WE660, KDL32WE610, KDL49WE754, KDL43WE754.
The update file and instructions can be downloaded from the manufacturer's website for the KDL-32WE613 model.
Benefits and improvements:
Fixed an issue where subtitles of some TV service providers were displayed incorrectly;
Improved overall TV stability.
Guides and instructions are also offered for this model:
Reference Manual (Web Manual). Published on 04 Apr 2018.
User manual. Published on 28 Nov 2019, size 1.95 MB.
Quick setup guide and quick start guide. Published on 11 Sep 2019, size 707 KB.
Wall-Mount Bracket. Published on 22 Nov 2017, size 39.47 MB.
SONY TV KDL-32WE613 with LCD HV320WHB-N5K, 31.5 "(80 cm) 16: 9 aspect ratio. This model uses Edge LED side illumination.
The HV320WHB-N5K sensor and MainBoard 1-981-541-21 software provide high quality HD viewing at 1366x768 pixels and 720p (HD Ready). Image processing is performed using modern High Dynamic Range (HDR) technology with an extended range of brightness gradations.
KDL-32WE613 TV has built-in SMART software and pre-installed Opera TV Operating System. Internet connection can be made via Wi-Fi wireless connection. Video processor supported media file formats: MP3, WMA, MPEG4, HEVC (H.265), Xvid, MKV, JPEG.
The power of the sound speaker system is 10 W (2x5 W), provided by two speakers. Uses the NICAM stereo signal processing system and the Sound Surround function.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), HDMI x2, USB x2, Ethernet (RJ-45), Wi-Fi 802.11n, Miracast. A headphone output is provided. The digital tuner is capable of receiving television channels in the DVB-T, DVB-T2, DVB-C standards.
The power consumed when operating from the network is 60 W. External power supply ACDP-060L01 Adapter 19.5V.
Dimensions: with stand 731x490x187 mm, without stand 731x442x70 mm.
TV weight: with stand: 6.2 kg, without stand: 5.8 kg.
Attention! The HV320WHB-N5K panel of the SONY KDL-32WE613 LED TV is the most expensive item.
Avoid impacts on the glass and excessive pressure on the screen surface to avoid damage to the LED panel!
It is unsafe for any liquid to spill on the screen. Sometimes one drop of water is enough, if it flows down the glass onto the plumes, the TV may become unrepairable.