Technical description and composition of the SAMSUNG UE32J5100AK TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE32J5100AK UE32J5100
Panel: CY-GH032BGSV1V
T-CON: RUNTK 5351TP 0055FV (52K04)
LED driver (backlight): integrated into MainBoard
PWM LED driver: 7014X
Power Supply (PSU): BN44-00697A REV1.4 L32SF_ESM PSLF720S06A
PWM Power: S3330 (FAN6755)
MOSFET Power: 60R580P
MainBoard: BN41-02098B BN94-08117P
IC MainBoard: F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414
Tuner: DNTS243EH286A BN40-00294A
Technical Specifications UE32J5100AK
SAMSUNG UE32J5100AK
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE32J5100AK does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
Often in such cases, the BN44-00697A power module is faulty. It is necessary to measure the output voltages in its secondary circuits, and if they are completely absent, check the serviceability of the power switches and rectifier diodes for a possible breakdown (short circuit).
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM circuits are usually checked by replacement with new ones, or known to be working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V for them. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its chips F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
If the TV works normally from external devices, but does not tune into television channels, the tuner DNTS243EH286A BN40-00294A may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention to users! Self-repair of a SAMSUNG UE32J5100AK TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!
The appearance of the MainBoard BN41-02098B is shown in the figure below:
BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel CY-JJ040BGNV2V), SAMSUNG UE40H5020 UE40H5020AK (Panel CY-GH040BGSV1V), SAMSUNG UE40J5100AU (Panel CY-GH040BGSR1V), SAMSUNG T31D310EW (Panel CY-HH032AGSV1H), SAMSUNG UE48J5000AU (Panel CY-JJ048BGEV5V), SAMSUNG UE32H5020AK (Panel CY-GH032BGLV4V), SAMSUNG UE40J5120AU (Panel CY-GH040BGSV1V), SAMSUNG LT32E310EX T32E310EX (Panel CY-GJ032BGEV1V), SAMSUNG UE40H5270 UE40H5270AU (Panel CY-GH048BGLV1V), SAMSUNG UE32J5100AK UE32J5100 (Panel CY- GH032BGSV1V), SAMSUNG UE32H5000AK UE32H5000 (Panel CY-GH032BGLV1V), SAMSUNG UE48H5000 UE48H5000AK (Panel CY-GH048CSLV1V), SAMSUNG UE32J5120AK UE32JSV1B (CY.
The appearance of the power supply
Main features of the SAMSUNG UE32J5100AK device:
Installed matrix (LED panel) CY-GH032BGSV1V.
The matrix control uses the Timing Controller (T-CON) RUNTK.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02098B, controlled by the 7014X PWM controller.
The necessary supply voltages for all nodes of the SAMSUNG UE32J5100AK TV are generated by the BN44-00697A power module or its analogs using S3330 microcircuits (FAN6755) and power switches of the 60R580P type.
MainBoard - the main board (motherboard) is a BN41-02098B module, using chips F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 and others.
The tuner DNTS243EH286A BN40-00294A provides the reception of television programs and tuning to channels.