Technical description and composition of the SAMSUNG UE32J5120AK TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE32J5120AK UE32J5120
Chassis / Version: MS02
Panel: CY-GH032BGSV1V
LED backlight: LM41-00099L
T-CON: RUNTK 5351TP ZA 0055FV + K5439TP 5440TP
LED driver (backlight): integrated into PSU
PWM LED driver: 7014X
Power Supply (PSU): BN44-00697A L32SF_ESM PSLF720S06A
PWM Power: S3330 = FAN6755W
MOSFET Power: 60R580P
MainBoard: BN41-02098B BN94-08117X
IC MainBoard: F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414
Tuner: BN40-00294A
Technical Specifications UE32J5120AK
SAMSUNG UE32J5120AK
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The SAMSUNG UE32J5120AK TV does not turn on and does not show any signs of operability at all. There is no reaction to the remote control and control buttons from the front panel.
Most often, with such manifestations, the main power module BN44-00697A is found to be faulty. In the absence of the necessary supply voltages in the secondary circuits of the converters, it is necessary to check the power switches (60R580P) and rectifier diodes for a possible partial or complete breakdown.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) S3330 = FAN6755W, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the health of its elements - F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 which may require replacement with new ones. If the BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
The malfunction of the tuner BN40-00294A is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair to professionals with sufficient experience in the repair of electronic equipment.
The appearance of the MainBoard BN41-02098B is shown in the figure below:
BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel CY-JJ040BGNV2V), SAMSUNG UE40H5020 UE40H5020AK (Panel CY-GH040BGSV1V), SAMSUNG UE40J5100AU (Panel CY-GH040BGSR1V), SAMSUNG T31D310EW (Panel CY-HH032AGSV1H), SAMSUNG UE48J5000AU (Panel CY-JJ048BGEV5V), SAMSUNG UE32H5020AK (Panel CY-GH032BGLV4V), SAMSUNG UE40J5120AU (Panel CY-GH040BGSV1V), SAMSUNG LT32E310EX T32E310EX (Panel CY-GJ032BGEV1V), SAMSUNG UE40H5270 UE40H5270AU (Panel CY-GH048BGLV1V), SAMSUNG UE32J5100AK UE32J5100 (Panel CY- GH032BGSV1V), SAMSUNG UE32H5000AK UE32H5000 (Panel CY-GH032BGLV1V), SAMSUNG UE48H5000 UE48H5000AK (Panel CY-GH048CSLV1V), SAMSUNG UE32J5120AK UE32JSV1B (CY.
The appearance of the power supply
Main features of the SAMSUNG UE32J5120AK device:
Installed matrix (LED panel) CY-GH032BGSV1V.
The matrix control uses the Timing Controller (T-CON) RUNTK.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a 7014X PWM controller.
The necessary supply voltages for all nodes of the SAMSUNG UE32J5120AK TV are generated by the BN44-00697A power module or its analogs using S3330 = FAN6755W microcircuits and 60R580P type power switches.
MainBoard - the main board (motherboard) is a BN41-02098B module, using chips F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 and others.
The tuner BN40-00294A provides the reception of television programs and tuning to channels