Technical description and composition of the TV AKAI LEA-39J29P, type of panel and applicable modules. The composition of the modules.AKAI LED
Model: LEA-39J29P
Chassis / Version: CV9202H-TPW
Panel: HF390BGA-C1
LED backlight: BN96-26928A BN41-02027A, 203SVS39F R5 / L8 REV1.9 130212
T-CON: 50T11-C02 T500HVN05.0 Ctrl BD
LED driver (backlight): CVA42003A-BL001
PWM LED driver: OB3350CP
MOSFET LED driver: AOD254
Power Supply (PSU): CVA42003
PWM Power: FAN7530, AP3105NA
MainBoard: CV9202H-TPW
IC MainBoard: CPU: SPV9202BD (1416-D), DRAM: K4B1G1646G-BCKO, SPI FLASH: Winb25Q64FVSIG, AUDIO: TPA3110LD2
Tuner: ST03WS-2A-E
Technical Specifications LEA-39J29P
AKAI LEA-39J29P
General repair guidelines for TV LCD LED
Possible malfunctions
- The AKAI LEA-39J29P TV does not turn on, does not respond to the remote control and the control panel buttons, the indicators do not light or flash.
Typically, with such manifestations, the defect is caused by faulty elements in the CVA42003 main power module. It is necessary to measure its output voltages, and in case of their absence, check the operability of the power switches of the converters and rectifier diodes for the probability of a short circuit.
In case of breakdowns in the secondary circuits, the converter, as a rule, can emergency work in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. Chips PWM (PWM) FAN7530, AP3105NA are usually checked by replacing with new, or obviously working.
- There is no image, there is sound, it responds to the remote control. Or the image may appear for a second when turned on and immediately disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as a health indicator. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the CV9202H-TPW motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). When repairing an MB board, you need to check its CPU components: SPV9202BD (1416-D), DRAM: K4B1G1646G-BCKO, SPI FLASH: Winb25Q64FVSIG, AUDIO: TPA3110LD2. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
If you suspect a malfunction of the ST03WS-2A-E tuner, first of all, you need to verify the correctness of the software, as well as the presence of the necessary voltage levels and pulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
Owners and users of the AKAI LEA-39J29P TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
FIRMWARE FOR SPI FLASH -----------> AKAI LEA-39J29P, Main: CV9202H-TPW, Panel: HF390BGA-C1
The appearance of the MainBoard CV9202H-TPW is shown in the figure below:CV9202H-TPW
CV9202H-TPW can be used in TVs:
AKAI LEA-39J29P (Panel HF390BGA-C1), BBK 32LEM-1001/T2C (Panel CX315DLEDM), DNS M39DM8 (Panel V390HJ1-P02 Rev C1), ERISSON 32LEE17 (Panel 720p HD 1366x768), FUSION FLTV-32T22 (Panel ST3151A05), FUSION FLTV-28T20 (Panel LCM-SM275TK301 (D0306)), FUSION FLTV-28T22 (Panel TH280L321-04), FUSION FLTV-32T23 (Panel ST3151A04-1 / Ver.2.4), FUSION FLTV-32T20 (Panel V320BK1-PS5 Rev.C7), TELEFUNKEN TF-LED40S28T2 (Panel CX400DLEDM), TELEFUNKEN TF-LED29S30T2 (Panel V290BJ1-XC01 CX290DLEDM), TELEFUNKEN TF-LED40S6T2 (Panel CX400DLEDM).
The appearance of the power supply
Key Features of the AKAI LEA-39J29P:
The matrix (LED panel) HF390BGA-C1 is installed.
The matrix control uses the Timing Controller (T-CON) 50T11-C02.
The LED driver CVA42003A-BL001 is used to power the backlight LEDs, it is controlled by the OB3350CP PWM controller. As the power elements of the LED driver, keys of the AOD254 type are used.
The necessary supply voltages for all nodes of the TV AKAI LEA-39J29P are generated by the CVA42003 power supply module or its analogs using FAN7530, AP3105NA microcircuits.
MainBoard - the main board (motherboard) is a CV9202H-TPW module, using the following CPU chips: SPV9202BD (1416-D), DRAM: K4B1G1646G-BCKO, SPI FLASH: Winb25Q64FVSIG, AUDIO: TPA3110LD2 and others.
The ST03WS-2A-E tuner provides TV reception and channel tuning.
Brand: AKAI, Model: LEA-39J29P.
Shortly from the TV: LCD, 1080p Full HD, diagonal 39 "(99 cm), HDMI connectors: 3, there is USB, there is support for DVB-T2, backlight type: Edge LED.
The composition uses MainBoard CV9202H-TPW and an LCD panel (matrix) HF390BGA-C1.
Power Supply Unit (PSU) CVA42003 Power Supply.
TV AKAI LEA-39J29P with LCD HF390BGA-C1, diagonal size 39 "(99 cm) 16: 9 format. This model is equipped with side LED backlight LED Edge. The design and technical capabilities of the TV include watching programs and movies in high quality HD at a resolution of 1920x1080 pixels in graphic decomposition according to the standard 1080p (Full HD). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p , 1080i, 1080p. Sub Supported media file formats: MP3, WMA, MPEG4, DivX, MKV, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI x3, USB, Bluetooth. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080. A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-T2 standards.
Overall dimensions: With a support 897x575x210 mm, Without a support 897x525x74 mm.
The mass of the TV: 8.2 kg.
Attention! The HF390BGA-C1 panel of the AKAI LEA-39J29P LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable