Saturday, 27 June 2020

REPAIR / SERVICING TV FUSION FLTV-40C11

Technical description and composition of the FUSION FLTV-40C11 TV, panel type and applicable modules. The composition of the modules.
FUSION LED
Model: FLTV-40C11
Chassis / Version: 40-M306PB-MAD2LG
Panel: LVF400CMOT E11
LED driver (backlight): integrated into MainBoard
PWM LED driver: TSOP-16
MOSFET LED driver: TO-252
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MainBoard: 40-M306PB-MAD2LG
IC MainBoard: CPU: MSD1306XSE-SB, SPI FLASH: 25Q32
Tuner: 07-389SI3-NF5G XF-3SA-H
Technical Specifications FLTV-40C110T
FUSION FLTV-40C11
General repair guidelines for TV LCD LED
Possible malfunctions
- The FUSION FLTV-40C11 does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
First of all, in such cases, you should verify the operability of the common switching power supply (IIP) - AC / DC voltage converter of the mains voltage. All source elements in this TV model are located on the MainBoard 40-M306PB-MAD2LG main board. It is necessary to measure its output voltages and, if they are absent, to check for short-circuit probabilities in the converters, power switches and rectifier diodes.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM SOT23-6 PWM controllers, in the absence of visible damage or obvious short-circuit between the terminals, are checked by replacing with new ones, or obviously working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
In such cases, the most likely malfunction of the LED backlight elements. The reason for this may be an open circuit in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V for them. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the 40-M306PB-MAD2LG motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sometimes it is necessary to check or replace (if necessary) the elements of the MainBoard - CPU: MSD1306XSE-SB, SPI FLASH: 25Q32. In cases where the BGA processor is used, its malfunction is usually detected by the local heating method.
If the TV works normally from external devices, but does not tune into television channels, the tuner XF-3SA-H may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
TV users and owners need to remember that attempts to independently repair a FUSION FLTV-40C11 TV without the appropriate qualifications and necessary experience can lead to serious negative consequences!



FIRMWARE FOR SPI FLASH  ----------->  FUSION FLTV-40C11, Main: 40-M306PB-MAD2LG, Panel: LVF400CMOT E11



The appearance of the MainBoard 40-M306PB-MAD2LG is shown in the figure below:

40-M306PB-MAD2LG

Main features of the FUSION FLTV-40C11 device:

Installed matrix (LED-panel) LVF400CMOT E11.
To power the backlight LEDs, a converter is used, combined with the main board 40-M306PB-MAD2LG, controlled by the TSOP-16 PWM controller. As power elements of the LED driver, keys of the TO-252 type are used.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is a 40-M306PB-MAD2LG module using CPU chips: MSD1306XSE-SB, SPI FLASH: 25Q32 and others.
Tuner 07-389SI3-NF5G XF-3SA-H provides the reception of television programs and tuning to channels.
 FUSION FLTV-40C110T TV with a 40 "(102 cm) diagonal LCD display in 16: 9 format. The required screen brightness of 280 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 100,000: 1 is achieved by special control of the LEDs. In technology The LED TV is used to make the screen of this TV model. The design and technical capabilities of the TV include watching programs and movies in high quality HD with a resolution of 1920x1080 pixels in graphic resolution according to the standard 1080p (Full HD). Supported media file formats: MP3, MPEG4, MKV, Jpeg.
The power of the sound system 16 W (2x8 W) provides two speakers. It uses the NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, VGA, HDMI x3, USB. An output for connecting headphones is provided.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Attention! The FUSION FLTV-40C110T LED TV panel is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.