Note on MAIN board replacement
New part of
EEP ROM (IC1103) on the MAIN board cannot be used.
Therefore, if the mounted MAIN board (A-1151-985-A, etc.) is replaced, exchange new EEP ROM (IC1103) with that used before the replacement.
Therefore, if the mounted MAIN board (A-1151-985-A, etc.) is replaced, exchange new EEP ROM (IC1103) with that used before the replacement.
When displaying the version number on the screen
When you turn on the system, the version number [VER.X.XX] (X is a number) may appear on the screen. Although this is not a malfunction and for Sony service use only, normal system operation will not be possible.
Turn off the system, and then turn on the system again to operate.
When you turn on the system, the version number [VER.X.XX] (X is a number) may appear on the screen. Although this is not a malfunction and for Sony service use only, normal system operation will not be possible.
Turn off the system, and then turn on the system again to operate.
When the self-diagnosis function is activated to prevent the
system from malfunctioning, a 5- character service number (e.g., C 13 50) with
a combination of a letter and 4 digits appears on the screen and the front
panel display.
C 13: The disc is dirty.
Clean the disc with a soft cloth.
Clean the disc with a soft cloth.
C 31: The disc is not inserted correctly.
Restart the system, then re-insert the disc correctly.
Restart the system, then re-insert the disc correctly.
E XX (xx is a number): To prevent a malfunction, the system has
performed the selfdiagnosis function.
Contact your nearest Sony dealer or local authorized Sony service
facility and give the 5- character service number.
Example: E 61 10
Example: E 61 10
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical pickup
block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH
1. Open the cover and turn POWER on with no disc inserted.
2. Confirm that the following operation is performed while observing the objecting lens.
1)Confirm that laser beam is spread.
2)Up and down motion of the objective lens. (3 times)
1. Open the cover and turn POWER on with no disc inserted.
2. Confirm that the following operation is performed while observing the objecting lens.
1)Confirm that laser beam is spread.
2)Up and down motion of the objective lens. (3 times)
DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration disc in the store is equipped.
Setting Procedure :
1. Press the Power button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the Stop button and the Eject button simultaneously for five seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the Stop button and the Eject button simultaneously for five seconds again.
2. The message “UNLOCKED” is displayed and the tray is unlocked.
The disc tray lock function for the antitheft of an demonstration disc in the store is equipped.
Setting Procedure :
1. Press the Power button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the Stop button and the Eject button simultaneously for five seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the Stop button and the Eject button simultaneously for five seconds again.
2. The message “UNLOCKED” is displayed and the tray is unlocked.
When “LOCKED” is displayed, the tray lock is not released by turning
power on/off with the Power button.
HOW TO OPEN THE DISC TABLE WHEN POWER
SWITCH TURNS OFF
Fix the capacitors with adhesive agent
as follows
Fixing the capacitors with adhesive agent is required by the safety regulation.
Be sure to fix the capacitors with adhesive agent when part or circuit board is replaced.
Fixing the capacitors with adhesive agent is required by the safety regulation.
Be sure to fix the capacitors with adhesive agent when part or circuit board is replaced.
When installing a new op unit / precaution
before unsoldering the static electricity prevention solder bridge
Be sure to connect the flexible printed circuit board first of all
before removing the static electricity prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by unsoldering after the
flexible printed
circuit board has already been connected.
(Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)
circuit board has already been connected.
(Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)
Disassembly and reassembly of the DVD mechanism
