C7 Chassis; TV 4472 AV SİLVER - F 772 GRAY - TV 8472 GRAY - F 972 BLACK - TV 9472 BLACK - F 372 SXS - TV 3472 SF - T 372 SXS - TV 3470 AVS - AL 570 XSL - TV 3482 AV SILVER 16: 9 - TV 6472 AV SILVER - F 472 SXS - T 984 SX SILVER - TV 5484 SILVER - TV 8572 SLIM - AL 572 F - SEDANCE 70 X - TV 3370 SN - AL-570 SF - F 572 SXS - TV 5472 AV SILVER - TV 7472 AV SILVER - F 872 SXS - AL-570 SF - AL-566 F - AL 572 F - AL 570 XS - TV 3484 S - TV 5482 AVS - TV 3472 AV SILVER - TV 3470 AVS - TV 5370 S - TV 3370 S - T 384 SXS - T 982 SXS -F 772 SXS - T 970 XS - T 370 XS - T 870 XS - T 870 X - T 870 SXS with model code C5G000 C5H000 C5J000 C5K000 C5L000 C5N000 C5Q000 C5R000 C5S000 C5U000 C5V000 C5KY000 C5U000 C5V000 C5KY CXD000 CXJ000 CXK000 CXL000 CXM000 CYX000 D9G000 E5W000 EAQ000 HCD000 J8A000 J8C000 M3T000 M3U000 M6H000 N5P000 UA9000 VK2000 VK3000 VZ9000 Y7G000 Y7H000 Y7J000 Y7K000 YA1000 for TV with barcode numbered, Beko branded.
C8 Chassis; Lenaro 72 Flat MF 72-5501 / 8 TOP - BOSTON 70 SX PIP VD - ELEGANCE 72 SX PF VD - ELEGANCE 72 SX PF PIP VD - BOSTON 70 SX PIP VD - SEDANCE 70 SX - T 970 SXS PIP - TV 5470 AVS PIP - F 772 VDX PIP - TV 4472 PIP VD - model code and C7G000 C7H000 D4N000 D4Q000 E5U000 E6A000 E6J000 E6K000 F3B000 J6W000 is used in Beko, Arçelik and Grundig brand televisions.
I6 Chassis (C8 IDTV); F 372 ID TV - TV 4472 IDTV - Lenaro 72Flat model code and P7H000 P7J000 barcode number is used in Arçelik, Beko and Grundig brand televisions.
M7 Chassis (C7 without tuner); 7472 CRT MONITOR - F 872 CRT MONITOR model code and FFD000 FFE000 GFJ000 GFK000 barcode number is used in Arçelik and Beko brand televisions.
Things to consider in ic101 malfunctions;
If the 3.3v inputs of the processor are short-circuited, be sure to check the 1.8v 3.3v output integrations before installing the new processor. There may be a problem in these integrators, causing the voltage to be lacking / excessive, and it will also cause you to break the new integration. before installing the integral; Check parts with chassis codes th601, r629 (12kilohms), ic603, ic606, d615, c631, d616, c632, r630, t604, t605, r652, r633, r641, r636, r634.
When you start the device, if there is 3.3 v from the 48 pin of the integrated, it will not work, it means that the ic101 is defective. That is, when you turn it on, the voltage in the leg no 48 is cut, if it is not cut, the chassis will not work.
If 145v is output directly, take the scl and sda feet of the ic401 to the tuner free, try if the TV works, the tuner is defective.
Annoying noise in the standby: add 6.8 kiloohm resistor from pin 11 of ic301 to negative end of c316
no standby: c622
d507 burning: l503
protect: fbt
145v direct output: ic101
There are return lines closing: r709 ic701
sawtooth forming in image: c504
turns off when the volume is too loud: c620
145v coming out directly: th601
A separate color prevails on the screen: 50 hz geom start line value will be set to 11-12 screen adjust -215 from the service menu
vertical: r659
no high voltage: ic101
display rainbow: ic501
vertical: ic604
led flashing: ic401
red dominant color distorts on the screen: reset video settings from the service menu
there is no sound there is no picture voltages are normal: from the remote menu 9301 press respectively p + ok p + ok. If it does not improve ic101
feed output bounces: r651
device works abnormally sound comes late: ic603 ic608 ic604 ic606
t504 bad c522 burst: t504 c522 c521
copying broadcast has hum: ic608
fliflop: c658
no osd: ic101
noise interference: ic605 c612
scan weak: c524
not controlling sound: c629
no color: Q101
screen wide sideways: r508 r524 c522
half of the screen is black from half down to white: reset video from the service menu
it works automatically without triggering, an instant high voltage comes out and the TV turns off: ic401
constantly burning t504: drop r515 to 60 ohms
145v direct output: r412
east / west corrupt: l501
light contrast is weak: t404
there are return lines on the screen: ic603
sound with no picture: ic608
voltages bounce: c613
no high voltage: d505 c502 c504 r525
all channels are the same: remove r101 and r102, put wire in their places
spontaneously changing channel: ic401
t504 lit: c502 c504
the screen gets bigger and smaller: c521 c522 r522
image ghosting: r709
osd text slipped and osd is not readable sound is cut off, everything becomes normal when warmed up: c612 c626 c639 c649
3.3v leg of ic101 is shorted: c114
screen left shift cannot be corrected from service menu: t410
When triggered, high voltage comes out and cuts off. There is a sound: after ic401 or triggering the device, press “menu 9 3 0 1 p + ok p + ok”
cut tube: r527
cannot trigger: c658
self-powered, remote does not control, no audio / video: software must be installed
When the high voltage comes out at the first power up, it switches to standby after a while, and this situation is repeated: 1.9 volts is 1.4. c648 depreciated
switches to standby shortly after being triggered: c649
there are lines on the screen: c644 c645 c639 c662 c647 c603
there is sound, the image comes on after a while and vibrates then the device turns off: ic608 c647 c648
device detects neither remote nor keypad after once powered up: software must be loaded
Image is as large as zoomed and wide at the sides: c522
Weak lines appear on the menu: c623
no sound. No sound signal comes out from legs 4 and 5 of ic101. software is installed but problem persists: ic101
High voltage does not come out when triggered and sometimes the led blinks during this time: crt
There is sound and no picture. When the screen turns on, blue return lines appear: t702 (on the crt card)
After 10 minutes of running, it lights up the ice90: block
no broadcast sound but loud chirp from speaker: c647 c625
vertical line on the screen: c521
When we start, the TV turns on, but there is scratching on both sides of the screen, eht it sounds like it is boiling. I tried eht deflection c504 but the problem continues: c547
doing p + constantly: insert an empty eprom
When the TV works a little, white g2 lines appear on the screen again, it becomes more frequent as it gets warmer:
d701 d702
there are harmonics on it so there are horizontally curved lines on the pictures: c623
lamp is blinking at standby 8.5 volts come out as 5 volts: wire r612
Stbyda cikcikcik constantly sounds until the jewelry starts: 15uf in the feed
no snow: t404 r418
t504 lights up when triggered: fbt l503
TV works normally for 1 hour, after 1 hour, the screen hurts on its own: r709
To enter the Service Menu; Press the 'menu' button on the remote control and dial '9 3 0 1'. Press the 'pp' button on the remote while you are in the Service Menu, Press the 'tv / tx' button to save the settings.