Technical description and composition of the ROLSEN RL-23L1003UF TV, panel type and modules used. The composition of the modules.ROLSEN LED
Model: RL-23L1003UF
Chassis / Version: T.VST29.A2B
Panel: M230HGE-L20 Rev. C1
LED driver (backlight): AY039D-1SF01
Power Supply (PSU): AY039D-1SF01
MainBoard: T.VST29.A2B_12313
IC MainBoard: PCU: TSUMV59XE-Z1, Sound: 1517P, SPI Flash: 25Q32RS1G
RL-23L1003UF Specifications
ROLSEN RL-23L1003UF
General recommendations for TV LCD LED repair
ROLSEN RL-23L1003UF TV, like many other electronic devices, it is advisable to start repairing by inspecting all external and internal elements. According to some external signs of a change in the state of some elements, it sometimes becomes possible to make assumptions about the nature of the defect, as well as to determine the further direction of troubleshooting. Swollen electrolytic or metal-ceramic capacitors, charred resistors, ring cracks in the soldering of the element terminals - all this can significantly help the master to determine the causes and consequences of the malfunctions in the TV.
If the RL-23L1003UF TV does not turn on, does not emit any sounds when turned on, as well as no indicators on the front panel are lit or blinking, there is a high probability of a malfunction in the power module. In some cases, only the stabilizer or power converter of the control processor may be faulty, which is typical for some ROLSEN models. In the absence of swollen capacitors of the secondary rectifier filter, diagnostics of the power supply should begin with checking the fuse and, if it is broken, it is necessary first of all to check all power semiconductor elements of the primary circuit - diodes and transistors for the likelihood of an avalanche or thermal breakdown.
It should be borne in mind that in the practice of repair, it is extremely rare for key transistors in switching power supplies (SMPS) to fail without reasons that should be looked for by checking other components, for example, a key breakdown can provoke faulty elements of damper circuits, or dried electrolytic capacitors or broken primary resistors power supply circuits involved in the stabilization process. In this case, all semiconductor elements of the strapping of the PWM regulator microcircuit are subject to verification, which it is advisable to check by replacement.
If the ROLSEN RL-23L1003UF TV has no picture, but there is sound, a malfunction is likely in the LED backlight circuits of the M230HGE-L20 Rev. C1 panel. It is also necessary to check the serviceability of the electrolytic capacitors of the filter of the secondary rectifiers of the PSU (power supply) for an overestimated ESR.
A malfunction in the backlight circuits often occurs due to an open circuit in the power supply circuit of the LED lines. It is required to disassemble the panel and check the LEDs themselves, the ration of their conclusions, as well as the reliability of the connections in the connectors and the ration of the connector pins.
An open circuit in the lines of LEDs connected in series cannot be detected with a multimeter or tester without disassembling the panel. It takes several tens of volts to open all the junctions, and it is best to use a current source for such purposes.
Diagnostics and repair of the T.VST29.A2B 12313 motherboard is carried out by checking the functionality of the stabilizers or power converters of the module chips. In some cases, a software update is required.
In some cases, it is necessary to check or replace (if necessary) elements of the MB (SSB) board - PCU: TSUMV59XE-Z1, Sound: 1517P, SPI Flash: 25Q32RS1G. In cases where a BGA processor is used, its malfunction is usually detected by the local warm-up method.
Attention to users! Self-repair of the ROLSEN RL-23L1003UF TV without proper qualifications and experience can lead to its complete non-repairability!
The appearance of the MainBoard T.VST29.A2B_12313 is shown in the figure below:
T.VST29.A2B_12313
T.VST29.A2B_12313 can be used in TVs:
DNS E19A00 (Panel CX185LEDM (V185B1-PE)), DNS E22A11 (Panel M215HGE-P02), DNS E22A00 (Panel CX215LEDM M215HGE-P01), DNS E16A20 (Panel TL156WH4 (TL)(N2)), ERISSON 24LEB15 (Panel M240HW01 VD), ROLSEN RL-19L1003U (Panel M185BGE-L10 Rev.C1), ROLSEN RL-22L1003U (Panel V216BG1-LE1 REV C1), ROLSEN RL-23L1003UF (Panel M230HGE-L20 Rev.C1), ROLSEN RL-23L1005UF (Panel M230HGE-L20 RevC1).
The main features of the ROLSEN RL-23L1003UF device:
Installed matrix (LED-panel) M230HGE-L20 Rev. C1.
AY039D-1SF01 LED driver is used to power the backlight LEDs.
The formation of the necessary supply voltages for all nodes of the ROLSEN RL-23L1003UF TV is carried out by the AY039D-1SF01 power module, or its analogs.
MainBoard - the main board (motherboard) is a T.VST29.A2B_12313 module, using PCU chips: TSUMV59XE-Z1, Sound: 1517P, SPI Flash: 25Q32RS1G and others.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: M230HGE-L20
Type: a-Si TFT-LCD, Panel
Diagonal size: 23.0 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 509.184x286.416 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 14S4P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
ROLSEN RL-23L1003UF TV with LCD M230HGE-L20, 23 "(58 cm) in 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 120,000: 1 is achieved by special control of LED operation The LED panel of this TV is equipped with Edge LED backlighting.The design and technical capabilities of the TV provide viewing of broadcasts and films in high quality HD at a resolution of 1920x1080 pixels in graphic resolution in the standard 1080p (Full HD) .Input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal formation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p Supported multimedia file formats: MP3, WMA, MPEG4, MKV, JPEG.
Speaker power of 6 W (2x3 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI, USB. A headphone output is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector on the TV case is used, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV in operating mode from the network is 50 watts.
TV weight: 4.5 kg.
Attention! ROLSEN RL-23L1003UF LED TV panel M230HGE-L20 Rev. C1 is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.