REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Friday 8 February 2019

VIZIO - VUR-8 _ UNIVERSAL REMOTE CONTROL _ SETUP PROCEDURE

VIZIO - VUR-8 _ UNIVERSAL REMOTE CONTROL _ SETUP PROCEDURE


PROGRAMMING FOR VCR


Note: The VIZIO Universal Remote Control does not feature a “VCR” device button, but you may program any of the device buttons to act as a VCR device selector, such as DVD, AUDIO or CABLE if you are not using one of those devices.
  • Manually turn on the VCR.
  • Press the button on the remote control which you have selected to control the VCR.
  • Press and hold the SET button until the LED LIGHT flashes twice.
  • Find the programming code for your VCR in the code list in the back of this book and enter it using the Number Buttons. If the code is accepted, the LED flashes twice after the last digit is entered.
  • If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for the device and manufacturer.
  • Point the remote control at the VCR and press the POWER button. The VCR will turn off.

If your VCR does not respond, try all the codes for your VCR brand. If the codes do not work, or your brand is not listed, see “Searching for Device Codes.”   Sometimes a code listed will only include limited functions. Try other codes that may include more functionality.

PROGRAMMING FOR CABLE SET-TOP BOX
  1. Manually turn on the Cable Box.
  2. Press the CBL button on the remote control.
  3. Press and hold the SET button until the LED LIGHT flashes twice.
  4. Find the programming code for your Cable Box in the code list in the back of this book and enter it using the Number Buttons. If the code is accepted, the LED flashes twice after the last digit is entered.  If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for the device and manufacturer.
  5. Point the remote control at the Cable Box and press the POWER button. The Cable Box will turn off.

If your Cable Set-Top Box does not respond, try all the codes for your brand. If the codes do not work, or your brand is not listed, see “Searching for Device Codes.”   Sometimes a code listed will only include limited functions. Try other codes that may include more functionality.

PROGRAMMING FOR DVD PLAYER
  • Manually turn on the DVD Player.
  • Press the DVD button on the remote control.
  • Press and hold the SET button until the LED LIGHT flashes twice.
  • Find the programming code for your DVD player in the code list in the back of this book and enter it using the Number Buttons. If the code is accepted, the LED flashes twice after the last digit is entered.  If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for the device and manufacturer.
  • Point the remote control at the DVD Player and press the POWER button. The DVD Player will turn off.

If your DVD player does not respond, try all the codes for your brand. If the codes do not work, or your brand is not listed, see “Searching for Device Codes.”  Sometimes a code listed will only include limited functions. Try other codes that may include more functionality.

SEARCHING FOR DEVICE CODES

If you cannot find the manufacturer in the device list or the program code does not work, you can use the remote control to search for the correct device code.
To search for a device code:
  1. Turn on the device.
  2. Press the matching device button on the remote control.
  3. Press and hold the SET button until the LED flashes twice.
  4. Press 9 9 1. The LED flashes twice.
  5. Point the remote control at the device and then alternate between pressing the POWER button and the device button on the remote control until the device turns off.
  6. If the device still does not respond, clear the device button, then repeat the search procedure.
CHANGING VOLUME LOCK

The remote control can be set to control volume through your TV while in Cable/Satellite, DVD, or VCR device modes.
To change the volume lock:
  • Press and hold the SETUP button until the LED flashes twice.
  • Press 9 9 3. The LED flashes twice.
  • Press the device button that you want once. The LED flashes twice. The selected device Volume will now be controlled using VOL+/VOL- while controlling those other devices.
TEACHING THE REMOTE CONTROL

It is recommended that both remotes have fresh batteries for the teaching function.Place teaching and learning remote controls no farther than 2” apart. If elapsed time between pressing keys is 10 seconds or longer the remote control will exit programming mode requiring you to start from Step 1.
  1. Press and hold down the SET key until led blinks twice.
  2. Input code 9 7 5, led blinks twice to confirm code acceptance.
  3. Press the Mode key. (DVD, Audio, Cable or TV).
  4. Press key to be learned. LED will blink rapidly.
  5. Press and hold key to be taught on teaching remote control.
  6. Led will stop blinking rapidly, then blink twice to confirm key has been programmed.
  7. Repeat Steps 3 through 6 until all desired keys are taught into your remote control.
  8. Exit learning mode by pressing SET or by waiting 10 seconds (time out).
CLEARING MEMORY
  • Press and hold down Set until Led blinks twice
  • Input code 9 8 1, led blinks twice signaling code acceptance.
  • In Step 2, code 9 7 7 can be used in instead.
  • The remote control is now ready to be programmed with original codes.
Posted By: FRANK at 05:38
TAG: ,