AOC 2216 LCD MONITOR service mode and power supply circuit +Monitor Repair
Contents of this article
- Service mode
- Power supply circuit
- White balance adjustment
Category: Lcd monitor Repair
AOC 2216
SERVICE MODE
How to enter to service
mode
Turn on power, press the Menu
button, pull out the power cord, and then plug the power cord. Then the factory
OSD will be at the left top of the panel.
Adjust the Picture
1.Press the MENU-button to
activate the OSD window.
2.Press+ or - to navigate
through the functions. Once the desired function is highlighted, press the
ENU-button to activate it. If
the function selected has a sub-menu, press or again to navigate through the
sub-menu unctions.Once the desired function is highlighted, presses MENU-button
to activate it.
3.Press+ or - to change the
settings of the selected function. To exit and save, select the exit function.
If you want to adjust any other
function, repeat steps 2-3.
OSD Lock Function: To lock the
OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To
un-lock the OSD - press and hold the MENU button while the monitor is off and
then press power button to turn the monitor on.
4.Press Exit key
continually for 7 sec. to turn on or off DDC-CI.
White- Balance,
Luminance Adjustment
Approximately
30 minutes should be allowed for warm up before proceeding White-Balance adjustment.
1. How to do the Chroma-7120 MEM .Channel
setting
A.
Reference to chroma 7120 user guide
B. Use
“SC” key and “NEXT” key to modify xyY value and use “ID” key to modify
the TEXT description Following is the procedure
to do white-balance adjust
2. Setting
the color temp. You want
A. 9300 color:
9300k color temp. parameter is x = 283 ±25, y = 297 ±25, Y = 180 ±25 cd/m2 ,
B. 7300 color:
7300k
color temp. parameter
is x = 299 ±25, y = 315 ±25, Y = 180 ±25 cd/m2
C. 6500 color:
6500k
color temp. parameter
is x = 313 ±25, y = 329
±25, Y = 180 ±25 cd/m2
D.SRGB
SRGB color temp. parameter is x = 313 ±25, y = 329 ±25, Y = 150 cd/m2
3. Enter into
factory mode of 2216Sw
Turn on power, press the Menu
button, pull out the power cord, and then plug the power cord. Then the factory
OSD will be at the left top of the panel.
4. Bias adjustment:
Set the Contrast to 90
Adjust the Brightness to 100.
5. Gain adjustment :
Move cursor to “-F-” and press MENU key
A. Adjust 9300k color-temperature
1.
Switch the Chroma-7120 to 9300k channel.
2. The chroma 7120 will show x = 283 ±25, y = 297 ±25, Y = 180 ±25 cd/m2
3. Switch the chroma-7120 to RGB MODE (with
press “MODE” button to change)
4.
Adjust the RED of
color 9300K on factory window until chroma 7120 indicator reached the value R=100
5.
Adjust the GREEN of
color 9300K on factory window until
chroma 7120 indicator reached the value
G=100
6.
Adjust the BLUE of
color 9300K on factory window
until chroma 7120 indicator reached the value B=100
7.
Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance
=100±2
B. Adjust 7300k color-temperature
1.
Switch the chroma-7120 to 7300k channel.
2. The chroma 7120 will show x = 299 ±25, y = 315 ±25, Y = 180 ±25 cd/m2
3. Switch the chroma 7120 to RGB MODE (with press “MODE” button
to change)
4.
Adjust the RED
of color 7300k
on factory window until chroma 7120 indicator reached the value R=100
5.
Adjust the GREEN of
color 7300k on factory window until chroma 7120 indicator reached the value G=100
6.
Adjust the BLUE of
color 7300k on factory window until chroma 7120 indicator reached the value B=100
7.
Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance
=100±2
C. Adjust 6500k color-temperature
1.
Switch the chroma-7120 to 6500K channel.
2. The chroma 7120 will show x = 313 ±25, y = 329 ±25, Y = 180 ±25 cd/m2
3. Switch the chroma 7120 to RGB MODE (with press “MODE” button
to change)
4.
Adjust the RED
of color 6500K
on factory window until chroma 7120 indicator reached the value R=100
5.
Adjust the GREEN of
color 6500K on factory window until chroma 7120 indicator reached the value G=100
6.
Adjust the BLUE of
color 6500K
on factory window
until chroma 7120 indicator reached the value B=100
7.
Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance
=100±2
D. Adjust SRGB color-temperature
1.
Switch the chroma-7120 to SRGB channel.
2. The chroma 7120 will show x = 313 ±25, y = 329 ±25, Y = 150cd/m2
3. Switch the chroma 7120 l to
RGB MODE (with press “MODE” button to change)
4.
Adjust the RED
of color sRGB on factory window
until chroma 7120 indicator reached the value R=100
5.
Adjust the GREEN of
color sRGB on factory window until chroma 7120 indicator reached the value G=100
6.
Adjust the BLUE of
color sRGB on factory window until chroma 7120 indicator reached the value B=100
7.
Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance
=100±2
E.
Press reset key and Turn the Power-button “off to on” to quit from factory mode.
POWER SUPPLY CIRCUIT
