PANASONIC PT-52LCX66 - PT-56LCX66 - PT-61LCX66 - PT-52LCX16 - PT-56LCX16 SERVICE MODE AND LED ERROR CODES
PANASONIC PT-52LCX66 - PT-56LCX66 - PT-61LCX66 - PT-52LCX16 - PT-56LCX16
SERVICE MODE AND LED ERROR CODES
RESET USER’S MEMORY FUNCTIONS
Be sure to reset the user’s memory:
- After replacing the Digital Tuner P.C.B.
- If the secret code for V-chip has been forgotten.
- When moving the unit to a new location.
- When resetting SOS (Error) number records.
1. Turn on the power.
2. Press and hold the VOLUME DOWN button on the unit and the OK key on the remote for more than 3 seconds. When reset is finished, power shuts off automatically (the user’s memory is reset).
Be sure to reset the user’s memory:
- After replacing the Digital Tuner P.C.B.
- If the secret code for V-chip has been forgotten.
- When moving the unit to a new location.
- When resetting SOS (Error) number records.
1. Turn on the power.
2. Press and hold the VOLUME DOWN button on the unit and the OK key on the remote for more than 3 seconds. When reset is finished, power shuts off automatically (the user’s memory is reset).
DO NOT UNPLUG AC CORD DURING COOLING OPERATION
The lamp cooling fan will continue to operate for approximately
1 minute after the power is turned off. At the same time, the POWER LED will flash red. Do not disconnect the AC Cord from the power outlet and do not open any circuit breakers while the cooling fan is still operating.
The lamp cooling fan will continue to operate for approximately
1 minute after the power is turned off. At the same time, the POWER LED will flash red. Do not disconnect the AC Cord from the power outlet and do not open any circuit breakers while the cooling fan is still operating.
WHEN INSTALLING THE PROJECTION UNIT OR THE BASE BODY UNIT INTO THE UNIT AT THE USER’S
LOCATION:
The following ADJUSTMENT of the Projection Unit must be performed.
a. Focus Adjustment
Note: The Focus Adjustment is not normally necessary when reinstalling. However, the Focus Adjustment should be performed when replacing the new Projection Unit or new Base Body Unit.
b. Mechanical Picture Position Adjustment
c. Electrical Picture Position Adjustment
Adjustment Preparation:
1. Install all parts except the Front Cover Unit Then, remove the Optical Cover by removing the Screw and 2 latch tabs.
The following ADJUSTMENT of the Projection Unit must be performed.
a. Focus Adjustment
Note: The Focus Adjustment is not normally necessary when reinstalling. However, the Focus Adjustment should be performed when replacing the new Projection Unit or new Base Body Unit.
b. Mechanical Picture Position Adjustment
c. Electrical Picture Position Adjustment
Adjustment Preparation:
1. Install all parts except the Front Cover Unit Then, remove the Optical Cover by removing the Screw and 2 latch tabs.
Note: When the rear cover is disassembled, the screen can be moved back
and forth, which could affect the video display vertical position. This could
also cause the vertical adjust to be at or near its limit. Only try the picture
position adjustment with the rear cover assembled!
2. Turn the power on.
3. Press and hold the VOLUME DOWN button on the unit and the RECALL key on the remote for more than 5 seconds in power on condition. "WORK MODE" will appear on the screen.
2. Turn the power on.
3. Press and hold the VOLUME DOWN button on the unit and the RECALL key on the remote for more than 5 seconds in power on condition. "WORK MODE" will appear on the screen.
4. Press the VCR key to go to VCR mode, then the
RECALL key on the remote for more than 1 second. "FACTORY ADJUST"
will appear on the screen.
5. Press the TV key to return to TV mode, then
press the CH UP/DOWN key on the remote to select "OTHER" on menu and
press the OK key. "OTHER" menu will appear.
6. Press the VOLUME UP/DOWN key on the remote. (Focus
screen will appear.)
To release this mode:
1. After completing the ADJUSTMENT, press the CH UP/ DOWN key on the remote to return to the OTHER menu.
2. Press RECALL key twice to return to Work Mode, and press and hold the VOLUME DOWN button on the unit and the RECALL key on the remote for more than 5 seconds. Or, turn off the power.
3. Install the Optical Cover with the Screw and the Front Cover Unit.
1. After completing the ADJUSTMENT, press the CH UP/ DOWN key on the remote to return to the OTHER menu.
2. Press RECALL key twice to return to Work Mode, and press and hold the VOLUME DOWN button on the unit and the RECALL key on the remote for more than 5 seconds. Or, turn off the power.
3. Install the Optical Cover with the Screw and the Front Cover Unit.
Electrical Picture Position
Adjustment
1) Adjust OPT HPOSI so that "C" is symmetrical to "D." by pressing the VOLUME UP/DOWN key on the remote to change the value.
2) Press the CH UP/DOWN key on the remote to return to the OTHER menu.
3) Select OPT VPOSI by pressing CH UP/DOWN key on the remote.
4) Adjust OPT VPOSI so that "A" is symmetrical to "B" by pressing the VOLUME UP/DOWN key on the remote to change the value.
1) Adjust OPT HPOSI so that "C" is symmetrical to "D." by pressing the VOLUME UP/DOWN key on the remote to change the value.
2) Press the CH UP/DOWN key on the remote to return to the OTHER menu.
3) Select OPT VPOSI by pressing CH UP/DOWN key on the remote.
4) Adjust OPT VPOSI so that "A" is symmetrical to "B" by pressing the VOLUME UP/DOWN key on the remote to change the value.
5) Confirm that all "A",
"B", "C", "D", "E", "F",
"G", "H", "I", "J", "K",
"L" are each almost symmetrical.
6) If not, adjust the "OPT HPOSI" and "OPT VPOSI" (repeat steps 1-6) until the picture is in the correct position.
7) Press the CH UP/DOWN key on the remote to return to the OTHER menu.
6) If not, adjust the "OPT HPOSI" and "OPT VPOSI" (repeat steps 1-6) until the picture is in the correct position.
7) Press the CH UP/DOWN key on the remote to return to the OTHER menu.
TO READ THE DIGITAL TUNER (PEAKS) SOFTWARE VERSION AND TV MICROCONTROLLER SOFTWARE VERSION
1. Press MENU key with the power on.
2. Press CH UP/DOWN key and select "Setup." Then press OK key.
3. Press CH UP/DOWN key and select "About." Then press OK key.
4. Select "Version" and press OK key. Version menu will appear as shown below. Starting with the second digit from the right or from the left.
1. Press MENU key with the power on.
2. Press CH UP/DOWN key and select "Setup." Then press OK key.
3. Press CH UP/DOWN key and select "About." Then press OK key.
4. Select "Version" and press OK key. Version menu will appear as shown below. Starting with the second digit from the right or from the left.
LED
ERROR CODES
Error
Information
|
POWER
LED
flashes orange |
TEMP
LED
flashes red |
LAMP
LED
flashes red |
SOS2 (Over
voltage/current)
|
1
|
||
Fan 1, Fan
2 or Fan 3 stops
|
2
|
||
Abnormal
voltage (DT+5V line)
|
3
|
||
IC5001
(GC4Pro) communication
error |
5
|
||
Temperature
Sensor shorted or open (Thermistor 2 P.C.B.)
|
2
|
||
Abnormal
temperature
(Thermistor 2 P.C.B.) |
3
|
||
Clogged Air
Filter
|
6
|
||
Abnormal
Lamp
|
1
|
||
Iris
Mechanism hardware error
|
2
|
||
Iris
calibration error
|
3
|
||
Lamp Cover
open
|
7
|
||
Abnormal
voltage (+17V, +9V, +5V line)
for LCD Drive P.C.B. |
8
|
Note:
1. The detected SOS Error 1) 2) 3) 4) 11) 12) data will be stored in the EEPROM.
2.SOS (Error) information is displayed in Service Mode (4/4).
3.LAMP OFF: The LED will flash immediately after the Lamp goes off.
4.In case of Error 9) or 10), the unit will not shut off and Dynamic Iris setting in Adv. adjust of Picture Menu will be changed to "OFF" automatically. When the unit is turned off and turned back on, Dynamic Iris "OFF" setting remains. Lamp LED will not flash as long as Dynamic Iris setting in Adv. adjust of Picture Menu is set to "ON" manually.
1. The detected SOS Error 1) 2) 3) 4) 11) 12) data will be stored in the EEPROM.
2.SOS (Error) information is displayed in Service Mode (4/4).
3.LAMP OFF: The LED will flash immediately after the Lamp goes off.
4.In case of Error 9) or 10), the unit will not shut off and Dynamic Iris setting in Adv. adjust of Picture Menu will be changed to "OFF" automatically. When the unit is turned off and turned back on, Dynamic Iris "OFF" setting remains. Lamp LED will not flash as long as Dynamic Iris setting in Adv. adjust of Picture Menu is set to "ON" manually.
