REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:

- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Wednesday 10 April 2019

SONY VPL-VW11HT SONY LCD PROJECTOR – – HOW TO RESET THE FILTER TIMER – HOW TO ENTER TO SERVICE MODE

Sony 3 LCD Projector – Sony VPL-VW11HT – How to reset the filter timer – How to enter to service mode



Sony 3LCD Projector – Sony VPL-VW11HT – How to reset the filter timer – How to entree to service mode – White balance adjustment – VCOM adjustment - Signal level adjustment
Sony VPL-VW11HT
Reset the air filter
1. Insert the Power Cord and let it standby.
2. Press the keys in the following ORDER: “RESET” > “MENU” > “DOWN” > “ENTER”
3. Turn the Power ON.
4. Please confirm that the message of “Please exchange the air filter” does not appear in the picture.
Factory Mode
1. Make sure that the STATUS in the menu is ON.
2. Exit the menu.
3 Press the keys in the following ORDER:
“ENTER” > “ENTER” > “LEFT” > “ENTER”
4. The message “Do you wish to enter into the FACTORY MODE?” will be displayed.
5. Select YES.
RGB VCOM Adjustment
1. Enter the P.DRV of the Device adjust with Factory mode.
2. Enter the item of 01 VCOM G, and check the 1 line ON/ OFF signal.
3. Adjust the LEFT and RIGH keys to minimize the flicker. Similarly, and perform Red and Blue adjustment similarly. (02 VCOM R, 03 VCOM B)
4. Select the SAVE TO MEMORY on the Device adjust page of the menu. Press the ENTER to save the data.
Signal Level Adjustment
Perform the following settings:
W/B: LOW mode
INPUT-A: 10 steps
VIDEO: 100% COLOR BARS
CONTRAST: 80
BRIGHT: 50 (Initial value)
SUB-BRIGHT (NTSC) Adjustment
1. Input the NTSC 100% color bars signal to the VIDEO input.
2. Connect oscilloscorp to TP5023 on the C board.
3. Set the COLOR to 0.
3. Enter the RGB-MTRX on the Device adjust of the menu.
4. Select the item of 03 SU BRT. Adjust the LEFT or RIGHT key so that the two bars at the center become flat.
SUB-CONT. HUE and COLOR (VIDEO) Adjustment
1. Input the NTSC 100% color bars signal to the VIDEO input.
2. Connect oscilloscope to TP5024 on the C board.
3. Set the COLOR to 0.
4. Enter the RGB-MTRX on the Device adjust of the menu.
5. Select the item of 08 YUV CONT, and adjust the amplitude of the following waveform for 0.63 Vp-p.
6. Set the COLOR to 50.
7. Select the item of 09 YUV COL. Adjust the LEFT or RIGH key so that the right and left bars are equal in level (A portion).
8. Select the item of 02 SUB HUE. Adjust the LEFT or RIGH key so that the two bars in the middle are equal in level (B portion).
9. Press the MEMORY key to save the data.
10. Similarly, perform steps 1 to 8 with PAL (100% Color Bars signal) system.
11. Press the MEMORY key to save the data.
VIDEO W/B Adjustment
Component W/B High Adjustment
Note: Set the COL to 50.
1. Input the Component Flat Field signal to INPUT-A, and select the COMPONENT by the INPUT-A of the SET SETTING.
2. Set the 06 3D GAMMA/THROUGH to 0.
3. Set the 07 3D GAMMA/SW to 1 (3D Gamma: ON).
4. Enter the W/B ADJUST HIGH from the menu.
5. Input the 80 IRE Component Flat Field signal to INPUT-A.
6. Adjust the chromaticity (x, y) to the values shown
below by the G GAIN and B GAIN of the W/B HIGH.
7. Input the 20 IRE Component Flat Field signal to INPUT-A.
8. Adjust the chromaticity (x, y) to the values shown below by the R GAIN and B GAIN of the W/B HIGH.
9. Repeat steps 5 to 8 until the chromaticity meets the below specifications.
10. Press the MEMORY key to save the data.
Specification:
Chromaticity (x) = 0.284 ± 0.005
Chromaticity (y) = 0.297 ± 0.005
Component W/B Low Adjustment
1. Enter the W/B ADJUST LOW from the menu.
2. Input the 80 IRE Component Flat Field signal to INPUT-A.
3. Adjust the chromaticity (x, y) to the values shown below by the G GAIN and B GAIN of the W/B LOW.
4. Input the 20 IRE Component Flat Field signal to INPUT-A.
5. Adjust the chromaticity (x, y) to the values shown below by the R GAIN and B GAIN of the W/B LOW.
6. Repeat steps 2 to 5 until the chromaticity meets the below specifications.
7. Press the MEMORY key to save the data. Specification:
Chromaticity (x) = 0.313 ± 0.005
Chromaticity (y) = 0.329 ± 0.005
W/B Low Custom Adjustment
1. Copy the data in the CUSTOM 1 to 4 using the menu.
CUSTOM 1: GAIN = RGB/HIGH
BIAS = VIDEO/HIGH
CUSTOM 2: GAIN = RGB/HIGH + 40
BIAS = VIDEO/HIGH
CUSTOM 3: GAIN = VIDEO/LOW + 40
BIAS = VIDEO/LOW (R GAIN is + 0)
CUSTOM 4: GAIN = VIDEO/LOW _20
BIAS = VIDEO/LOW (R GAIN is + 0)
2. Press the MEMORY key to save the data.
V-COM Adjustment
1. Enter the P.DRV of the Device adjust with Factory mode.
2. Enter the item of 01 VCOM G, and check the 1 line ON/OFF signal.
3. Adjust the LEFT and RIGHT keys to minimize the flicker. Similarly, and perform Red and Blue adjustment similarly. (02 VCOM R, 03 VCOM B)
4. Select the SAVE TO MEMORY on the Device adjust page of the menu. Press the ENTER to save the data.