REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Saturday, 14 December 2019

DAEWOO DLT-42U1GMB, DLT-42G1LTBD, DLT-46U1UMB, DLT-46U1STB - LCD TV - HOW TO ENTER THE SERVICE MODE, TROUBLESHOOTING

Daewoo 42 and 46 inch LCD TV – service mode and adjustments, troubleshooting procedure - CHASSIS : SL-701T


Daewoo DLT-42U1GMB, DLT-42G1LTBD, DLT-46U1UMB, DLT-46U1STB - LCD TV - How to enter the service mode, Troubleshooting.
SERVICE MODE
Using the Service Remote controller, you can enter service mode directly. [SERVICE REMOCON : R-34SVC(S/N:48B3034SVC)]
EEPROM initial DATA
Description of SERVICE MODE ITEM
A. S1(1): Heat-Run Key
B. S2(2): Gumi Channel Map Write
C. S3(3): Volume Test.  => This key can check sound
D. S4(4): EDIE WRITE => Using this key, you can update EDID data below method.
1. Connect two jumpers (P502) vertically.
2. Press "S4" key and then, TV set display "EDID WRITE OK" upper left of screen.
3. If EDID writing is fail, TV set display "EDID Write Error" upper left of screen.
4. After EDID write, remove jumper.
E. S5(5): PANEL TEST. => Using this key, you can test problem of PANEL, as confirm white pattern, red pattern,blue pattern, green pattern.
F. S6(6): PICTURE TEST => Using this key, you can test brightness, contrast and color.
G. S7(7): DEMPOL CHANNEL MAP WRITE
H. S8(8): EEPROM Erase and White Balance adjustment. => Using this key, you can erase EEPROM data and adjust White balance.
I. S9(9): Device control. => This key only use for R&D.
J. S10(10): Option key. => Using this key, you can adjust SSC, Dimming, Panel Type, Control key and etc.
K. S11(11): I2C STOP key. => This key only use for R&D.
L. S12(SLEEP): Shipping key. => Using this key, you can set up at shipping mode.
Trouble Shooting
When “No signal” in RF, SCART1,SCART2,AV3
1) First check if other inputs are working. =>If other inputs are not working, replace MAIN PCB.
2) Checking waveform with Color Bar Pattern (Using the oscilloscope).
-Main TP (RF): CC613 near IC601 (Top).
-Main TP(SCART1): LC019 near JP208 (Top).
-Main TP(SCART2): LC213 near JP207 (Top).
-Main TP(AV3): RC055 near P240. => If all TP signal does not appear, replace MAIN PCB.
When “No Signal” in Y/C signal (S-Video)
1) First check if other inputs are working. =>If other inputs are not working, replace MAIN PCB
2) Checking waveform with Color Bar Pattern (Using the oscilloscope).
-Main TP(Y signal): RC053 near P240.
-Main TP(C signal): RC050 near P240.
=> If all TP signal does not appear, replace MAIN PCB.
When “No Signal” in Y/Pb/Pr signal (Component)
1) First check if other inputs are working. =>If other inputs are not working, replace MAIN PCB.
2) Checking waveforms with Color Bar Pattern (Using the oscilloscope).
-Main TP (COMP_Y): RC233 near JP211 (Top).
-Main TP (COMP_Pb): RC234 near JP211 (Top).
-Main TP (COMP1_Pr): RC235 near JP211 (Top).
=> If all TP signal does not appear, replace MAIN PCB.
When “No Signal” in PC
1) First check if other inputs are working. =>If other inputs are not working, replace MAIN PCB.
2) Checking waveforms with Color Bar Pattern (Using the oscilloscope).
-Main TP(R signal): RC629 near IC601(Top).
-Main TP(G signal): RC627 near IC601 (Top).
-Main TP(B signal): RC628 near IC601 (Top).
-Main TP(H-Sync): RC630 near IC601 (Top), -Main TP(V-Sync): RC640 near IC601 (Top).
=> If all TP signal does not appear, replace MAIN PCB.
When “No Signal” in HDMI
1) First check if other inputs are working. =>If other inputs are not working, replace MAIN PCB.
2) Checking waveform with Color Bar Pattern (Using the oscilloscope).
-Main TP (RC672, RC671, RC670, RC668, RC667, RC666, RC665) near IC601. => If all TP signal does not appear, replace MAIN PCB.
When Key does not operate.
42G1 : replace the key PCB.
42/46 U1 : replace the touch button.
Trouble diagnosing or repairing.
A. Trouble diagnosing and repairing of set mean find out which PCBs or blocks are not working and replace them with new PCBs. Repairing the broken PCBs are not necessary. Keep the broken PCBs and return them to service center or R&D center.
B. This TROUBLE DIAGNOSIS list only contains representative and simple PCB trouble diagnosis and Module Exchange method. Therefore, if you find Sets that are difficult to diagnosis or to repair, contact R&D center.
C. Basic TROUBLE DIAGNOSIS process.
D. Required equipment for trouble diagnosis [Digital Multimeter]
User Mode: measure DC VOLTAGE, DIODE VOLTAGE, SHORT/OPEN TEST
-Screwdriver or electric screwdriver, plastic adjusting tool
-Oscilloscope (for detailed examination only)
E. Each BLOCK operations explained here, but these are for reference only and utilizing them to repair PCBs is not necessary.
F. Before replacing PCBs, you MUST turn off the AC switch.
G. After replacing POWER, MAIN and SUB PCB, extra adjustment might be needed.
H. After the set is repaired, leave BACK COVER open for followings. Run HEATRUN for at least 30 minutes by displaying TEST PATTERN (Full White) of SERVICE MODE.
Check the screen conditions and basic functions.(Remote Controller operation etc.).
J. After BACK COVER is closed, redo HEATRUN for at least one hour with Full White input using TEST PATTERN of SERVICE MODE. Check the screen conditions and basic functions.
Posted By: FRANK at 08:40
TAG: , , , ,