
SAMSUNG LED
Model: UE48H5270AU UE48H5270
Panel: CY-GH048BGLV1V
T-CON: BN41-02111A
LED driver (backlight): integrated into PSU; 195V 450mA
PWM LED driver: 7014X
MOSFET LED driver: AOD5N40
Power Supply (PSU): BN44-00703A - L48S1_ESM
PWM Power: SEM3051 (PFC), FA6A01N (PWM resonant)
MOSFET Power: 13N60M2 (PFC), 50R380P
MainBoard: BN41-02098B - BN94-07141W
IC MainBoard: Nand Flash: ESMT F59L1G81A - 25TI, SPI Flash; 25Q40CLSIP, RAM: K4B2G1646Q - BCKO, AUDIO: NTP7414, S24C256, AOZ3015PI
Tuner: BN40-00294A
Control: IR: H5000_SW BN41-02149A
Technical Specifications UE48H5270
SAMSUNG UE48H5270AU
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE48H5270AU TV does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
With such manifestations, a malfunction is most likely to be detected in the BN44-00703A power supply module. It is necessary to measure its secondary output voltages, and in case of their absence, check the serviceability of power switches (13N60M2 (PFC), 50R380P) of converters and rectifier diodes for possible short circuit.
In case of breakdowns of diodes in the secondary circuits, the converter can operate in emergency short circuit mode without output voltages, and during short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor at the source of the key usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) SEM3051 (PFC), FA6A01N (PWM resonant), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
The correct operation of the PFC unit can be judged by the presence of an increased voltage (380-400V) on the electrolytic capacitor of the network rectifier filter in operating mode.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
In such cases, the most likely malfunction of the LED backlight elements. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. A zener diode PN junction indirectly indicates a LED-a
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Board repair and replacement of Nand Flash chips: ESMT F59L1G81A - 25TI, SPI Flash; 25Q40CLSIP, RAM: K4B2G1646Q - BCKO, AUDIO: NTP7414, S24C256, AOZ3015PI are produced with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
Before replacing the tuner BN40-00294A, if there is no tuning to the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Attention to users! Self-repair of a SAMSUNG UE48H5270AU TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!
FIRMWARE FOR SPI FLASH -----------------------> SAMSUNG UE48H5270AU UE48H5270
The appearance of the MainBoard BN41-02098B is shown in the figure below:
BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel

The appearance of the power supply
Main features of the SAMSUNG UE48H5270AU device:
Installed matrix (LED-panel) CY-GH048BGLV1V.
The matrix control uses the Timing Controller (T-CON) BN41-02111A.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a 7014X PWM

The necessary supply voltages for all nodes of the SAMSUNG UE48H5270AU TV are generated by the BN44-00703A power module or its analogs using SEM3051 (PFC), FA6A01N (PWM resonant) microcircuits and 13N60M2 (PFC), 50R380P type power switches.
MainBoard - the main board (motherboard) is a BN41-02098B module using Nand Flash chips: ESMT F59L1G81A - 25TI, SPI Flash; 25Q40CLSIP, RAM: K4B2G1646Q - BCKO, AUDIO: NTP7414, S24C256, AOZ3015PI and others.
The tuner BN40-00294A provides the reception of television programs and tuning to channels.