Technical description and composition of the LG 42LB690V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 42LB690V
Chassis / Version: LD42B
Panel: LC420DUH (PG) (F1)
LED backlight: 6916L-1682A, 6916L-1683A, 6916L-1684A, 6916L-1685A
LED driver (backlight): integrated into PSU
PWM LED driver: iW7025-00
Power Supply (PSU): EAX65424001 (2.4) Rev.3.0
PWM Power: NCP1034DG, MAP8800, ICE3BR4765JZ
MOSFET Power: 13N60M2
MainBoard: EAX65384004 (1.5) EBT63100015
IC MainBoard: CPU: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR
Tuner: TDJM-G101D
Control: IR: YNE4F90000A EBR77978483, WIFI: LGSBW41
Specifications 42LB690V
LG 42LB690V
General repair guidelines for TV LCD LED
Possible malfunctions
- LG 42LB690V does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
Most often, with such manifestations, the main power supply module EAX65424001 is found to be faulty. It is necessary to measure its output voltages and, if they are absent, check the power switches (13N60M2) and rectifier diodes for the probability of short circuit in the converters.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the main fuse usually breaks.
Breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback (OOS) stabilization circuits. PWM controllers (PWM) NCP1034DG, MAP8800, ICE3BR4765JZ, if they do not have visible damage to the case and open short circuit between the terminals, are usually checked by replacement.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
In such cases, the most likely malfunction of the LED backlight elements. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It should be remembered that it is not possible to determine the break in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a failure, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the EAX65384004 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of attempts to repair the MB board (SSB), it is necessary to check the health of its elements - CPU: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
If the TV works normally from external devices, but does not tune into television channels, the TDJM-G101D may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention TV owners! Attempts at self-repair of LG 42LB690V are not recommended by the manufacturer and can lead to serious negative consequences!
schematic diagram ------------> LG 42LB690V Chassis LD42B
The appearance of the MainBoard EAX65384004 is shown in the figure below:EAX65384004
EAX65384004 can be used in TVs:
LG 32LB650V ZE (Panel LC320DUH (FG)(P2)), LG 47LB650V ZE (Panel LC470DUH (FG) (P2)), LG 42LB650V (Panel LC420DUH (FG)(P2)), LG 42LB671V ZF (Panel LC420DUH (PG) (F1)), LG 47LB671V (Panel LC470DUH (PG)(F1)), LG 42LB653V ZK (Panel LC420DUH (FG)(P1)), LG 42LB720V (Panel LC420DUH (PG)(F1)), LG 42LB658V (Panel LC420DUH (FG)(P2)), LG 47LB677V (Panel LC470DUH (FG)(F1)), LG 42LB679V (Panel LC420DUH (PG)(F1)), LG 47LB653V (Panel LC470DUH (FG)(P1)), LG 32LB653V (Panel LC320DUH( FG)(P1)), LG 42LB690V (Panel LC420DUH (PG)(F1)), LG 55LB630V (Panel LC550DUH).
The appearance of the power supply
Main features of the device LG 42LB690V:
Installed matrix (LED-panel) LC420DUH (PG) (F1).
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the iW7025-00 PWM controller.
The necessary supply voltages for all nodes of the LG 42LB690V TV are generated by the EAX65424001 power module or its analogs using NCP1034DG, MAP8800, ICE3BR4765JZ microcircuits and 13N60M2 type power switches.
MainBoard - the main board (motherboard) is an EAX65384004 module, using CPU chips: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR and others.
The TDJM-G101D tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC420DUH-PGF1
Type: a-Si TFT-LCD, Panel
Diagonal size: 42 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 927.94x521.96 mm
Surface: Antiglare (Haze 1%), Hard coating (3H)
Brightness: 400 cd / m²
Contrast Ratio: 1400: 1
Display Colors: 1.06B (10-bit), CIE1931 72%
Response Time: 8/10 (Tr / Td)
Frequency: 120Hz
Lamp Type: WLED Without Driver
Signal Interface: EPI, 100 pins
Voltage: 12.0V
