Technical description and composition of the MYSTERY MTV-4829LTA2 TV, panel type and applicable modules. The composition of the modules.MYSTERY LED
Model: MTV-4829LTA2
Chassis / Version: MS63082-ZC01-01
Panel: LSC480HN02-G // LSC480HJ01-8
T-CON: 13YR_S60TMB3C2LV0.1
LED driver (backlight): integrated into PSU
PWM LED driver: OB2263, AP3616M28-G1
MOSFET LED driver: MDF0765
Power Supply (PSU): TV4205-ZC02-01
PWM Power: FAN7930 (PFC), OB2273
MainBoard: MSAV3220-ZC26-02 (B) // MS63082-ZC01-01
IC MainBoard: CPU: MSD308BT-SW, SPI Flash: GD25Q64B, EEPROM T-con 24C16, Scaller: NT71263FG-300
Tuner: LHD
Control: IR: TV3210-ZC25-03 (3) B
Technical Specifications MTV-4829LTA2
MYSTERY MTV-4829LTA2
General repair guidelines for TV LCD LED
MYSTERY MTV-4829LTA2, like other televisions, it is advisable to start repairing from inspection of external and internal elements and modules. Visible damage to elements can sometimes indicate the direction of the search for a defect even before the necessary measurements are taken. Carbonized paint on the upper layer of resistors, electrolytic capacitors of rectifier filters swollen after boiling, cracked soldering at the terminals of heating elements or transformers can often suggest the cause of the defect and possible consequences.
A malfunction of the power supply is often manifested corny - the TV does not turn on, does not make any sounds, does not light up and does not blink with any indicators. When diagnosing and repairing the power supply, first of all, replace the swollen filter capacitors of the secondary rectifiers and check the fuse and, if it is broken, it is necessary to identify the cause. Often in such cases, an avalanche (thermal) breakdown is detected in the power semiconductor elements of the module — rectifier diodes and transistors in the primary circuit.
Mos-Fet keys used in switching power supplies (SMPS) rarely fail for no reason to look for when checking other circuit elements. Often the breakdown is caused by malfunctions of electrolytic capacitors or semiconductor elements in the primary circuit, or by a break in the resistors in the stabilization circuits. The PWM controller chip can also cause a breakdown of the power switch of the converter.
In cases where the MYSTERY MTV-4829LTA2 TV has lost its image, and the sound is there and all other functions are operational, there is a possibility of a malfunction of the LED driver (converter for powering the backlight LEDs of the LSC480HJ01-8 panel). When you turn on the TV, the image may appear briefly and disappear immediately. It must be borne in mind that with such manifestations the LEDs themselves also fail.
A malfunction in the backlight circuits often occurs due to an open in the power circuit of the LED lines. It requires disassembling the panel and checking the LEDs themselves, the rations of their terminals, as well as the reliability of the connections in the connectors and rations of the terminals.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the LED will light up slightly.
On the motherboard MS63082-ZC01-01, in case of a malfunction, you should first check the performance of all the stabilizers and power converters of the microcircuits, and also, if necessary, update the software (software).
Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - SPI Flash: GD25Q32; and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board technologies. Typically, such defects are detected by local heating of the chip.
Owners and users of the MYSTERY MTV-4829LTA2 TV must remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
FIRMWARE FOR SPI FLASH -----------> MYSTERY MTV-4829LTA2, Main: MS63082-ZC01-01, Panel: LSC480HJ01-8
To reduce the backlight current in LED drivers with the AP3616M28-G1 terminal stage, the total resistance of the resistors from terminal 22 (ISET AP3616M28) to the housing should be proportionally increased. The maximum current in each of the 16 channels is 75 mA. To increase the current in the diodes, the channels are connected in parallel. The current in milliamperes in each channel is determined from the calculation of 1560 * 1.194 / Rset, where Rset is the resistance from the ISET output to the housing in kilo-ohms.
Repair MainBoardThe appearance of the MainBoard MSAV3220-ZC26-02 (B) is shown in the figure below:
MSAV3220-ZC26-02
MSAV3220-ZC26-02 can be used in TVs:
BBK LEM3284DT2 (Panel LSC320AN02), MYSTERY MTV-2224LT2 (Panel CLAA215FA10), MYSTERY MTV-4028LTA2 (Panel V390HJ1-P02), MYSTERY MTV-4829LTA2 (Panel LSC480HN02-G), MYSTERY MTV-4129LT2 (Panel LK400D3HC34K), MYSTERY MTV-2424LT2 (Panel HM236WU8-200 ), MYSTERY MTV-4030LT2 (Panel V400HJ6-PE1), MYSTERY MTV-4629LTA2 (Panel HV460WU2-200).
The appearance of the power supply
Main features of the MYSTERY MTV-4829LTA2 device:
Installed matrix (LED panel) LSC480HN02-G or LSC480HJ01-8.
The matrix control uses the Timing Controller (T-CON) 13YR_S60TMB3C2LV0.1.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by the OB2263 PWM controller, AP3616M28-G1. As power elements of the LED driver, keys of the MDF0765 type are used.
The necessary supply voltages for all nodes of the MYSTERY MTV-4829LTA2 television are generated by the TV4205-ZC02-01 power supply module or its analogs using FAN7930 (PFC), OB2273 microcircuits.
MainBoard - the main board (motherboard) is an MSAV3220-ZC26-02 module, using CPU chips: MSD308BT-SW, SPI Flash: GD25Q64B, EEPROM T-con 24C16, Scaller: NT71263FG-300 and others.
The LHD tuner provides television reception and channel tuning.
MYSTERY MTV-4829LTA2 TV with LSC480HN02-G LCD, 48 "(122 cm) diagonal in 16: 9 format. The required screen brightness of 280 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 2000: 1. Edge LED backlighting is implemented in the LED-panel of this TV - Edge LED.The design and technical capabilities of the TV include watching programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphical decomposition according to the standard 1080p (Full HD).
MTV-4829LTA2 TV has built-in SMART Software and pre-installed Android Operating System. Connecting to the Internet can be done via Wi-Fi. The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
The power of the acoustic system of sound 20 W (2x10 W) provide two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, VGA, HDMI x2, USB x2, Ethernet (RJ-45), Wi-Fi 802.11n. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
The power consumed by the TV in the operating mode from the network is 72 watts.
Overall dimensions: With stand 642x444x209 mm, Without stand 642x398x44 mm.
Attention! The LSC480HN02-G panel of the MYSTERY MTV-4829LTA2 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
