Technical description and composition of the ROLSEN RL-24A09105 TV, panel type and modules used. The composition of the modules.ROLSEN LED
Model: RL-24A09105
Panel: V236BJ1-L01 REV.C1
T-CON: V236BJ1-XC01; CM501, CM1801B, CM601
LED driver (backlight): RSAG7.820.4550 / RON
PWM LED driver: AZ494CP-E1
MOSFET LED driver: BA2S1H (4616)
Trans LED driver: SPI-EEL23-A05 (SHT-230-006)
PWM Power: NCP1271A
MOSFET Power: BP62806 (STK076)
MainBoard: HFT248CN116H / RON
IC MainBoard: MT8223LEMU (1229-BMTL), 4HC4052D, F4558, M21-120, 24C16, ME4953, Z1031AIAP1534
Control: ER-31607R
RL-24A09105F Specifications
ROLSEN RL-24A09105
General recommendations for TV LCD LED repair
Repair of electronic devices, including the ROLSEN RL-24A09105 TV, is advisable to start with an external examination of its external and internal elements. It often happens that visible damage to elements or connections helps determine the direction of troubleshooting. If charred resistors, swollen electrolytic or sintered capacitors, ring cracks in the soldering of the terminals of transformers or heating elements are found, it is advisable to establish the causes and consequences of the malfunction, as well as to check the connected elements and assemblies.
In the case when the RL-24A09105 does not turn on, does not respond to the remote control and front panel buttons, does not blink the lights and does not show any signs of operability, the V236BJ1-L01 REV.C1 power supply module is probably faulty in this case. If it is working properly with such manifestations, it is necessary to check the processor power regulator (converter) on the motherboard.When diagnosing and repairing the power supply, after replacing the swollen capacitors of the secondary rectifier filters (if any), you must first of all check the mains fuse. If it breaks, you should check the power elements of the BP62806 (STK076) transistors and the rectifier bridge diodes for avalanche (thermal) breakdown.
As a rule, switches in switching power supplies (SMPS) are quite reliable and rarely fail without reasons that should be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM microcircuit is checked by replacing it with a known good one.
If the ROLSEN RL-24A09105 has no picture, but there is sound and the TV is controlled from the remote control, a malfunction is likely in the V236BJ1-L01 REV.C1 panel backlight circuits. LEDs or power converter - LED driver may be faulty. Often in such cases, when you turn on the TV, an image appears and immediately disappears. First of all, it is necessary to make sure that the electrolytic capacitors of the rectifier filter supplying the LED driver are in good working order, and check the LEDs by connecting those that are known to be working for diagnostics.
To check the health of the LEDs, as well as the contact connections in the ruler circuit, the panel must be disassembled.
To identify an open circuit in the LED lines without disassembling the panel, a current source is required. It is impossible to open the junctions connected in series with a simple multimeter; a voltage of several tens of volts is required.
On the HFT248CN116H / RON motherboard, in the event of a malfunction, you should first check the operability of all stabilizers or power converters of microcircuits and, if necessary, update the software (software).
If it is not possible to replace the MB (SSB) board, it is necessary to check the serviceability of its elements - MT8223LEMU (1229-BMTL), 4HC4052D, F4558, M21-120,24C16, ME4953, Z1031AIAP1534 ,. Defective components must be replaced.
Owners and users of the ROLSEN RL-24A09105 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to the complete non-repairability of the device!
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> ROLSEN RL-24A09105, Main: RSAG7.820.2009/ROH VER.D Cpu: MT8223LFMU 1147-BMSL, Flash: MX25L1606E, Panel: V236H1-01 REV.C3
The main features of the ROLSEN RL-24A09105 device:
Installed matrix (LED panel) V236BJ1-L01 REV.C1.
Matrix control uses Timing Controller (T-CON) V236BJ1-XC01 ;.
To power the backlight LEDs, the RSAG7.820.4550 LED driver is used, controlled by the AZ494CP-E1 PWM controller. The transformer SPI-EEL23-A05 (SHT-230-006) is installed in the LED driver converter. The keys of the BA2S1H (4616) type are used as power elements of the LED driver.
The necessary supply voltages for all nodes of the ROLSEN RL-24A09105 TV are provided by a switching power supply using NCP1271A microcircuits and power switches of the BP62806 (STK076) type.
MainBoard - the main board (motherboard) is a HFT248CN116H module, using MT8223LEMU (1229-BMTL), 4HC4052D, F4558, M21-120, 24C16, ME4953, Z1031AIAP1534 chips and others.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: V236BJ1-L01
Type: a-Si TFT-LCD, Panel
Diagonal size: 23.6 inch
Resolution: 1366x768, WXGA
Display Mode: MVA, Normally Black, Transmissive
Active Area: 521.471x293.184 mm
Surface: Antiglare (Haze 3.5%), Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 8.5 (G to G)
Frequency: 60Hz
Lamp Type: 2 pcs CCFL Without Driver
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
ROLSEN RL-24A09105F TV with LCD V236BJ1-L01, 24 "(61 cm) 16: 9 format diagonal. Screen brightness 300 cd / m² backlit by CCFL (EEFL) fluorescent lamps. Contrast as a ratio of maximum brightness to minimum, is 800: 1. The design and technical capabilities of the TV provide viewing of broadcasts and films in high quality HD at a resolution of 1920x1080 pixels in graphic resolution according to the standard 1080p (Full HD). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal shaping takes place in 480i, 480p, 576i, 576p, 720p, 1080i, 1080p standards Supported media file formats: MP3, JPEG.
The power of the acoustic system of sound 4 W (2x2 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, S-Video, component, SCART, RGB, VGA, HDMI, USB. A headphone output is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector on the TV case is used, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV in operating mode from the network is 50 watts.
Dimensions: with stand 592x421x167 mm, without stand 592x394x103 mm.
TV weight: 7 kg.
Attention! ROLSEN RL-24A09105F LCD TV panel V236BJ1-L01 is the most expensive component.
Avoid hitting the glass and putting pressure on the screen surface to avoid irreversible damage to the LCD panel!
