Technical description and composition of the TELEFUNKEN TF-LED32S38T2 TV, panel type and modules used. The composition of the modules.TELEFUNKEN LED
Model: TF-LED32S38T2
Chassis / Version: MS34631-ZC01-01
Panel: LSC320AN09-H
LED backlight: LED315D10-07 (B) 30331510219
T-CON: 16Y_GH11MB7S4LV0.2
LED driver (backlight): integrated into MainBoard
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MainBoard: MS34631-ZC01-01
IC MainBoard: SPI FLASH 25Q64
Tuner: DVB-T2
Control: TV3024-ZC10-01 (C)
TF-LED32S38T2 Specifications
TELEFUNKEN TF-LED32S38T2
General recommendations for TV LCD LED repair
Possible manifestations of defects
- TELEFUNKEN TF-LED32S38T2 TV does not turn on. There are no signs of operability. The indicators on the front panel do not light up or blink, the TV does not respond to the remote control and control buttons.
In such cases, the common power source is often faulty - the AC / DC converter of the mains voltage, which is combined with the elements of the MS34631-ZC01-01 main board. Then we recommend measuring its output voltages and, if they are absent, you should check the serviceability of the power switches and rectifier diodes of the converters for a possible short circuit.
In case of diode breakdowns in the secondary circuits, the converter can operate in an emergency mode of short circuit without output voltages, and with a short circuit in the power elements of the primary circuit, the mains fuse and / or the current sensor in the source of the key usually breaks off.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can disable it in the key mode, or create an excess of the maximum permissible key parameters. These can be elements supplying a PWM regulator, frequency setting or damper circuits, or elements of negative feedback in the stabilization circuit. PWM controllers, in the absence of visible damage or outright short circuits between the terminals, are checked by replacing them with new ones, or knowingly working properly.
- There is no picture, but there is sound and reaction to commands from the remote control. Or the image appears immediately after switching on and disappears.
As a rule, in such cases there is no display backlight. The reason for this may be an open circuit in the LED circuit, or a problem in stabilizing their power supply.
When diagnosing, it must be borne in mind that it is impossible to check for an open in the circuit of the LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally a current source. By opening the panel, you can check each LED separately. Typically, Chinese multimeters light up one 3-volt LED slightly if the probes are connected to it in the forward direction. For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of LED health. In the event of a malfunction of the LED, its zener diode will either be cut off or broken into the K / Z.
- The indicator blinks or is on constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the MS34631-ZC01-01 motherboard should begin with checking the stabilizers and power converters required to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Repair of the board and replacement of SPI FLASH 25Q64 microcircuits are performed if the necessary equipment and the corresponding element base are available. Malfunctions associated with the use of BGA soldering technologies can be localized by warming up.
Malfunction of the DVB-T2 tuner is established after checking the software and all supply voltages at its terminals. The I2C bus data exchange between the tuner and the processor can be monitored with an oscilloscope.
Attention! Users and owners of TF-LED32S38T2 TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from trying to repair themselves in order to avoid negative consequences that can lead to the complete non-repairability of the device.
The appearance of the MainBoard MS34631-ZC01-01 is shown in the figure below:
MS34631-ZC01-01
Main features of the TELEFUNKEN TF-LED32S38T2 device:
Installed matrix (LED panel) LSC320AN09-H.
Matrix control uses Timing Controller (T-CON) 16Y_GH11MB7S4LV0.2.
A converter combined with the MS34631-ZC01-01 main board is used to power the backlight LEDs.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is a MS34631-ZC01-01 module, using SPI FLASH 25Q64 chips and others.
The DVB-T2 tuner provides reception of television programs and tuning to channels.
PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages
In
the circuitry of modern switching power supplies (SMPS), PWM
controllers made in small-sized planar packages with six terminals have
gained wide popularity. The enclosure type designation can be SOT-23-6,
SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the
pins are shown in the figure below. In this case, the code marking
LD7530A is shown on the left fragment of the picture.
Pin assignment:
1 - GND. (Common wire).
2
- FB. (FeedBack - Feedback). Input for controlling the duration of
pulses with a signal from the output voltage. Sometimes it can be
labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC -
Depending on the type of microcircuit, it can be used for a
frequency-setting RC circuit (RI / RT / CT), or for organizing
protection, as an input of a PWM trip comparator at a threshold value at
its input, specified in the document. In some types of microcircuits,
this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.
Functionally,
these regulators work on the principle of the previously popular xx384x
PWM microcircuits, which have proven themselves well in terms of
reliability and stability.
Some difficulties often arise when
replacing or choosing an analog for such PWM regulators due to the use
of code markings in the designation of the type of microcircuits. The
situation is complicated by a large number of component manufacturers
who do not always provide documentation to the mass access, just as not
all manufacturers of finished devices supply repair service centers with
diagrams, so repairmen often have to study real circuit solutions by
installed components and wiring connections directly on the board.
In
practice, PWM microcircuits and the marking code EAxxx and Eaxxx are
often found. Official documentation for them was not found in the public
domain, but discussions on the forums and pieces of pictures from PDF
from System General, which publishes them as SG6848T and SG6848T2, have
survived. The drawing is here placed left .
For the attention of the masters, here below are PDF datasheet tables
compiled from information available on the Internet and PDF documents
for the selection of analogues types when replacing the most common
six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP),
pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| SG6849 | SG684965TZ | Fairchild / ON Semi | BBxx |
| SG6849 | SG6849-65T, SG6849-65TZ | System General | MBxx EBxx |
| SGP400 | SGP400TZ | System General | AAKxx |
PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.
When
applying the PWM listed below, the frequency should be set with the RT
(RI) resistor from pin 3 to ground. Usually its nominal value is chosen
95-100 kOhm for a frequency of 65-100 KHz. For more details, see the
here below attached documentation. PDF files are packed in RAR.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3103A | AP3103AKTR-G1 | Diodes Incorporated | GHL |
| AP8263 | AP8263E6R, A8263E6VR | AiT Semiconductor | S1xx |
| AT3263 | AT3263S6 | ATC Technology | 3263 |
| CR6848 | CR6848S | Chip-Rail | 848H16 |
| CR6850 | CR6850S | Chip-Rail | 850xx |
| CR6851 | CR6851S | Chip-Rail | 851xx |
| FAN6602R | FAN6602RM6X | Fairchild / ON Semi | ACCxx |
| FS6830 | FS6830 | FirstSemi | |
| GR8830 | GR8830CG | Grenergy | 30xx |
| GR8836 | GR8836C, GR8836CG | Grenergy | 36xx |
| H6849 | H6849NF | HI-SINCERITY | |
| H6850 | H6850NF | HI-SINCERITY | |
| HT2263 | HT2263MP | HOT-CHIP | 63xxx |
| KP201 | Kiwi Instruments | ||
| LD5530 | LD5530GL LD5530R | Leadtrand | xxt30 xxt30R |
| LD7531 | LD7531GL, LD7531PL | Leadtrend | xxP31 |
| LD7531A | LD7531AGL | Leadtrend | xxP31A |
| LD7535/A | LD7535BL, LD7535GL, LD7535ABL, LD7535AGL | Leadtrend | xxP35-xxx35A |
| LD7550 | LD7550BL, LD7550IL | Leadtrend | xxP50 |
| LD7550B | LD7550BBL, LD7550BIL | Leadtrend | xxP50B |
| LD7551 | LD7551BL/IL | Leadtrend | xxP51 |
| LD7551C | LD7551CGL | Leadtrend | xxP51C |
| NX1049 | XN1049TP | Xian-Innuovo | 49xxx |
| OB2262 | OB2262MP | On-Bright-Electronics | 62xx |
| OB2263 | OB2263MP | On-Bright-Electronics | 63xx |
| PT4201 | PT4201E23F | Powtech | 4201 |
| R7731 | R7731GE/PE | Richtek | 0Q= |
| R7731A | R7731AGE | Richtek | IDP=xx |
| SD4870 | SD4870TR | Silan Microelectronics | 4870 |
| SF1530 | SF1530LGT | SiFirst | 30xxx |
| SG5701 | SG5701TZ | System General | AAExx |
| SG6848 | SG6848T, SG6848T1, SG6848TZ1, SG6848T2 | Fairchild / ON Semi | AAHxx EAxxx |
| SG6858 | SG6858TZ | Fairchild / ON Semi | AAIxx |
| SG6859A | SG6859ATZ, SG6859ATY | Fairchild / ON Semi | AAJFxx |
| SG6859 | SG6859TZ | Fairchild / ON Semi | AAJMxx |
| SG6860 | SG6860TY | Fairchild | AAQxx |
| SP6850 | SP6850S26RG | Sporton Lab | 850xx |
| SP6853 | SP6853S26RGB, SP6853S26RG | Sporton Lab | 853xx |
| SW2263 | SW2263MP | SamWin | |
| UC3863/G | UC3863G-AG6-R | Unisonic Technologies Co | U863 U863G |
| XN1049 | XN1049, XN1049TP | Innuovo Microelectronics | 49 xxx |
PWM controllers that use pin 3 differently.
When
using the following PWM (PWM controllers), you should pay attention to
pin 3, which can be used to organize protection - thermal or from
overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3105/V/L/R | AP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1 | Diodes Incorporated | GHN GHO GHP GHQ |
| AP3105NA/NV/NL/NR | AP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1 | Diodes Incorporated | GKN GKO GKP GKQ |
| AP3125A/V/L/R | AP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1 | Diodes Incorporated | GLS GLU GNB GNC |
| AP3125B | AP3125BKTR-G1 | Diodes Incorporated | GLV |
| AP3125HA/HB | AP3125HAKTR-G1, AP3125HBKTR-G1 | Diodes Incorporated | GNP GNQ |
| AP31261 | AP31261KTR-G1 | Diodes Incorporated | GPE |
| AP3127/H | AP3127KTR-G1, AP3127HKTR-G1 | Diodes Incorporated | GPH GSH |
| AP3301 | AP3301K6TR-G1 | Diodes Incorporated | GTC |
| FAN6862 | FAN6862TY | Fairchild / ON Semi | ABDxx |
| FAN6863 | FAN6863TY, FAN6863LTY, FAN6863RTY | Fairchild / ON Semi | ABRxx |
| HT2273 | HT2273TP | HOT-CHIP | 73xxx |
| LD7510/J | LD7510GL, LD7510JGL | Leadtrend | xxP10 xxP10J |
| LD7530/A | LD7530PL, LD7530GL, LD7530APL, LD7530AGL | Leadtrend | xxP30 xxxP30A |
| LD7532 | LD7532GL | Leadtrend | xxP32 |
| LD7532A | LD7532AGL | Leadtrend | xxP32A |
| LD7532H | LD7532HGL | Leadtrend | xxP32H |
| LD7533 | LD7533GL | Leadtrend | xxP33 |
| LD7536 | LD7536GL | Leadtrend | xxP36 |
| LD7536R | LD7536RGL | Leadtrend | xxP36R |
| LD7537R | LD7537RGL | Leadtrend | xxP37R |
| LD7539C GL | LD7539C GL | Leadtrend | xxP39C |
| ME8204 | ME8204M6G | MicrOne | ME8204xx |
| NCP1250 | NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1G | ON Semiconductor | 25xxxx |
| NCP1251 | NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1G | ON Semiconductor | 5xxxxx |
| OB2273 | OB2273MP | On-Bright-Electronics | 73xx |
| R7735 | R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGE | Richtek | |
| UC3873/G | UC3873-AG6-R, UC3873G-AG6-R | Unisonic Technologies | U873 U873G |
TV TELEFUNKEN TF-LED32S38T2 with LCD LSC320AN09-H, 31.5 "(80 cm) 16: 9. Brightness 240 cd / m² is provided by LED backlight. Dynamic contrast ratio of 5000: 1 is achieved by special LED control. The technology of manufacturing the screen of this TV model is realized with LED backlighting.It is possible to view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready) Supported media file formats: MP3, WMA, MPEG4, Xvid, MKV, JPEG.
Speaker power of 10 W (2x5 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI x2, USB. A headphone output is provided.
The digital tuner is capable of receiving TV channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Overall dimensions: 730x473x200 mm.
TV weight: 5.5 kg.
Attention! The LSC320AN09-H panel of the TELEFUNKEN TF-LED32S38T2 LED TV is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV non-repairable.
