Technical description and composition of the LG 32LB582V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 32LB582V ZG
Chassis / Version: LE46B / LD46B
Panel: LC320DUE (FG) (A4)
LED driver (backlight): integrated into PSU; 117V, 250mA
PWM LED driver: SSC1S311, A27RAE (sot-26)
MOSFET LED driver: STD11N65M5, MDHT4N20Y
Power Supply (PSU): LGP32-14PL1
PWM Power: NCP1251, NR134S
MOSFET Power: KP8N65
MainBoard: EAX65610904 - NC4-M-TU24
IC MainBoard: H5TQ4G63AFR, EEPROM: 24C256, SOUND: Audio: NTP7513
Tuner: TDJM-G101D EBL61400501
Specifications 32LB582V
LG 32LB582V
General repair guidelines for TV LCD LED
Possible malfunctions
- The LG 32LB582V TV does not turn on and does not show any signs of operability at all. There is no reaction to either the remote control or the front panel control buttons.
With such manifestations, a malfunction is likely to be detected in the LGP32-14PL1 power supply module. It is necessary to measure its secondary output voltages, and in case of their absence, check the serviceability of the power switches (KP8N65) of the converters and rectifier diodes for the presence of a probable short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power switch may be PWM (NWP1251, NR134S). It is checked only by replacement with a known good one.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
Often in such cases, there is no LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, sometimes you can detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the EAX65610904 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). If it is not possible to replace the MB board (SSB), you need to check the health of its elements - H5TQ4G63AFR, EEPROM: 24C256, SOUND: Audio: NTP7513. Defective components should be replaced.
Before replacing the TDJM-G101D EBL61400501 tuner, if there is no channel setting, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
TV users and owners need to remember that attempts to self-repair an LG 32LB582V TV without the appropriate qualifications and necessary experience can lead to serious negative consequences!One of the typical failures of the LG 32LB582V ZG often occurs in the LG panel LC320DUE (FG) (A4).
External manifestations: there is no image, the backlight does not work. In most such cases, the LEDs turn out to be malfunctioning, which during testing turn out to be either in a cliff or with broken internal zener diodes.
LEDs must be replaced, and the maximum current from the driver should be limited to 10-20%.
You can reduce the backlight current in LG TVs with LGP32-14PL1 power supplies (EAX65391401) as follows. The current sensor consists of six resistors R816-R821 connected in parallel - 1 Ohm, 1 Ohm, 1 Ohm, 1 Ohm, 2 Ohm, 8.2 Ohm. The total resistance in this case will be 0.22 Ohm. If you remove one resistor 1 Ohm, the total resistance increases to 0.28 Ohm, the current decreases proportionally from 250 mA to about 190 mA.
More details on this page
Service manual and schematic diagram -----------------> LG 32LB582V Chassis LD46B.
CHASSIS : LD46B; MODEL : 32LB58**, 32LB58**-Z*, 32LB580V, 32LB580V-TA
The appearance of the MainBoard EAX65610904 is shown in the figure below:EAX65610904
EAX65610904 can be used in TVs:
LG 32LB582V ZG (Panel LC320DUE (FG)(A4)), LG 42LB570V (Panel LC420DUE (FG)(A4)), LG 42LB5800 (Panel LC420DUE (P6)(A4)), LG 42LB580V (Panel LC420DUE (FG)(A4)), LG 32LB570U 32LB570U-ZJ (Panel NC320DXN VSBP2), LG 39LB580V (Panel T390HVF02.0 HC390DUN-VCHS1), LG 32LB580V ZB (Panel LC320DUE (FG)(A4)).
The appearance of the power supply
Main features of the device LG 32LB582V:
Installed matrix (LED panel) LC320DUE (FG) (A4).
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by a PWM controller SSC1S311, A27RAE (sot-26). As the power elements of the LED driver, keys of the type STD11N65M5, MDHT4N20Y are used.
The necessary supply voltages for all nodes of the LG 32LB582V TV are generated by the LGP32-14PL1 power module, or its analogs using NCP1251, NR134S microcircuits and KP8N65 type power switches.
MainBoard - the main board (motherboard) is an EAX65610904 module, using H5TQ4G63AFR microcircuits, EEPROM: 24C256, SOUND: Audio: NTP7513 and others.
Tuner TDJM-G101D EBL61400501 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: LG Display
Model: LC320DUE-FGA4
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 698.4x392.85 mm
Surface: Antiglare (Haze 1%), Hard coating (3H)
Brightness: 300 cd / m²
Contrast Ratio: 1200: 1
Display Colors: 16.7M (8-bit), CIE1931 66%
Response Time: 7 (G to G)
Frequency: 60Hz
Lamp Type: WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V
