Technical description and composition of the DEXP F22B3000E TV, type of panel and applicable modules. The composition of the modules.DEXP LED
Model: F22B3000E
Chassis / Version: CVMV29L-F
Panel: T215HVN01.1 CX215LEDM
LED backlight: CXE220160000-X2
T-CON: M215HVN01.0 21M07-C04
LED driver (backlight): integrated into PSU
PWM LED driver: OB3350CP
MOSFET LED driver: AOD450
Power Supply (PSU): MP24S-CX
PWM Power: OB2273 (PWM SOT23-6)
MainBoard: CVMV29L-F
IC MainBoard: CPU: TSUMV59XU-Z1, Flash: Winbond 25Q32BVSIG, SOUND: NS4263
Tuner: CDT-3NP5I1-10 (R620D)
Technical Specifications F22B3000E
DEXP F22B3000E
General repair guidelines for TV LCD LED
Possible malfunctions
- The DEXP F22B3000E TV does not turn on, does not respond to the remote control and the control panel buttons, the indicators do not light or flash.
In such cases, the adapter power supply is usually faulty.
The owner of the TV can purchase an external power supply unit such as Adapter and repairing it is not always advisable. In any case, the simplest typical defects characteristic of most IIP schemes can be easily detected and eliminated after opening. Then we recommend that you measure its output voltages and, if they are absent, you should check the health of the power switches and rectifier diodes of the converters for a probable short circuit.
In case of breakdowns of diodes in the secondary circuits, the converter can operate in emergency short circuit mode without output voltages, and during short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor at the source of the key usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
Often in such cases, there is no LED backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the CVMV29L-F motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sometimes it is necessary to check or replace (if necessary) the elements of the MainBoard board - Cpu: TSUMV59XU-Z1, Flash: Winbond 25Q32BVSIG. In cases where the BGA processor is used, its malfunction is usually detected by the local heating method.
If the TV works normally from external devices, but does not tune into television channels, the tuner CDT-3NP5I1-10 may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Entrust repair to professionals with sufficient experience in the field of repair of electronic equipment.
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> Chassis CVMV29L-F
FIRMWARE FOR SPI FLASH -----------> DEXP F22B3000E, Main: CVMV29L-F, Panel: T215HVN01.1 CX215LEDM
The appearance of the MainBoard CVMV29L-F is shown in the figure below:CVMV29L-F
CVMV29L-F can be used in TVs:
DEXP H24C3000E (Panel CX236DLEDM), DEXP H16B3000ED (Panel N156BGE-L21), DEXP F22B3000E (Panel T215HVN01.1 CX215LEDM), DEXP 16A3000 (Panel N156BGE-L2 1366x768 WXGA ), DEXP 19A3000 (Panel CX185LEDM), DEXP 22A7000 (Panel CX215LEDM), MYSTERY MTV-1628LW (Panel N156BGE-L21), MYSTERY MTV-1629LW (Panel N156BGE-L21), SUPRA STV-LC16741WL (Panel NT156WHM-N12), SUPRA STV-LC16740WL (Panel LTN156AT32).
The appearance of the power supply
Main features of the DEXP F22B3000E device:
The matrix (LED panel) T215HVN01.1 CX215LEDM is installed.
The matrix control uses the Timing Controller (T-CON) M215HVN01.0.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by the OB3350CP PWM controller. As power elements of the LED driver, keys of the AOD450 type are used.
The necessary supply voltages for all nodes of the DEXP F22B3000E TV are generated by the MP24S-CX power module or its analogs using OB2273 microcircuits (PWM SOT23-6).
MainBoard - the main board (motherboard) is a CVMV29L-F module, using Cpu chips: TSUMV59XU-Z1, Flash: Winbond 25Q32BVSIG, SOUND: NS4263 and others.
The tuner CDT-3NP5I1-10 (R620D) provides the reception of television programs and tuning to channels.
Technical description
TV DEXP F22B3000E with LCD T215HVN01.1, diagonal size 22 "(56 cm) 16: 9 format. The required brightness of the screen 200 cd / m² is provided by LED backlight LED. Contrast - the ratio of maximum brightness to minimum is 3000: 1. This model uses a panel with the end position of the backlight LEDs - Edge LED.The TV features include viewing programs and movies in high quality HD with a resolution of 1920x1080 pixels in graphic resolution according to the standard 1080p (Full HD). Input high-frequency or video signal l decoded in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768, 1920x1080.
Overall dimensions: 500x340x170 mm.
Mass of the TV: 3.53 kg.
Attention! The T215HVN01.1 CX215LEDM panel of a DEXP F22B3000E LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
