Technical description and composition of the SUPRA STV-LC2610W TV, panel type and modules used. The composition of the modules.SUPRA
Model: STV-LC2610W
Chassis / Version: LS09
Panel: LCG260B1-L01
MainBoard: LS09 JUG7.820.990-2
IC MainBoard: CPU MST6E181VS-LF-Z1, Flash EN25Q32
Tuner: CDT-3BP4I1-36
Technical Specifications STV-LC2610W
SUPRA STV-LC2610W
General recommendations for TV LCD repair
SUPRA with LS09 JUG7.820.990-2 chassis, like other TVs, it is advisable to start repairing with a careful examination of external and internal elements and modules. Specific external damage to some elements can sometimes indicate further actions to determine the malfunction of the TV and localization of the defect before the necessary measurements are taken. In most cases, the repairman can guess about the causes of the defect and the possible consequences by the characteristic signs of typical defects in TVs, for example, the formed ring cracks in the soldering of the element terminals, swollen capacitors of the rectifier filter, charred resistors and other circuit elements.
In cases when the SUPRA STV-LC2610W TV does not turn on, does not respond to the remote control and buttons, no indicators on the front panel light up or blink, and there are no sounds and no signs of operation when turned on, - most likely the power module is faulty or there is no power processor on the motherboard (typical defect of some SUPRA TV models). Diagnostics and repair of the common power supply should always begin with checking the mains fuse and the condition of the electrolytic capacitors of the secondary rectifier filters. Defective and swollen capacitors should be replaced with new ones. If the fuse breaks, it is advisable to check for a breakdown, first of all, all the power semiconductor elements of the converter and the diode bridge of the rectifier network, as well as the large electrolytic capacitor of the filter of the rectifier network.
As a rule, switches in switching power supplies (SMPS) are quite reliable and rarely fail without reasons that should be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM microcircuit is checked by replacing it with a known good one.
If SUPRA STV-LC2610W has no picture, but there is sound and the TV is controlled from the remote control, a malfunction in the display backlight units is likely. The lamps or the power converter - inverter may be faulty. Often in such cases, when the TV is turned on, an image appears and immediately disappears. First of all, it is necessary to verify the operability of the electrolytic capacitors of the rectifier filter supplying the inverter, and check the LCD lamps by connecting external and obviously serviceable for diagnosis to the connectors. If, when diagnosing a malfunction, it is required to turn off the inverter protection, there is a risk of failure of the power elements of the inverter, and special care is required during work, and after they are completed, it is necessary to restore the protection circuits for further safe operation of the TV by the owner in normal mode.
In cases of attempts to repair the LS09 JUG7.820.990-2 motherboard, it is necessary to check the operability of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating. Board repair and replacement of CPU chips MST6E181VS-LF-Z1, Flash EN25Q32 are carried out with the necessary equipment, and the corresponding element base. Malfunctions associated with the use of BGA soldering technologies can be localized by warming up.
Remember! Attempts to self-repair by users of a SUPRA STV-LC2610W TV without the appropriate qualifications and necessary experience can lead to serious negative consequences!
FIRMWARE FOR SPI FLASH -----------> SUPRA STV-LC2610W LS09 JUG7.820.990-2, Main: LS09 JUG7.820.990-2, Panel: LCG260B1-L01
The appearance of the MainBoard JUG7.820.990-2 is shown in the figure below:JUG7.820.990-2
Main features of the SUPRA STV-LC2610W device:
Installed matrix (LCD panel) LCG260B1-L01.
The required supply voltage for all nodes of the TV SUPRA STV-LC2610W provides a switching power supply.
MainBoard - the main board (motherboard) is an LS09 module, using CPU MST6E181VS-LF-Z1, Flash EN25Q32 and others.
The tuner CDT-3BP4I1-36 provides the reception of television programs and tuning to channels.
LCD TV SUPRA STV-LC2610W with LCD LCG260B1-L01, 26 "(66 cm) 16: 9. Brightness of the screen of 500 cd / m² provided by backlighting CCFL (EEFL) fluorescent lamps. Dynamic contrast ratio 4000: 1 achieved by special control of the backlight.You can watch broadcasts and movies and images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal is decoded in analog systems PAL, SECAM, NTSC. Graphic processing and digital generation The signal occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i.
The power of the sound system 10 W (2x5 W) provide two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV x2, component x2, VGA, HDMI. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV in operating mode from the network is 120 watts.
Overall dimensions: 720x530x235 mm.
TV Weight: 9.5 kg.
Attention! The LCG260B1-L01 panel of the SUPRA STV-LC2610W LCD TV is the most expensive component.
Avoid hitting the glass and exerting pressure on the screen surface to avoid permanent damage to the LCD panel!
