Technical description and composition of the TV AIWA 47LE61103, panel type and applicable modules. The composition of the modules.AIWA LED
Model: 47LE61103
Chassis / Version: V1L09
Panel: LC470EUN (SE) (F1)
LED backlight: EDGE LED
T-CON: 6870C-0401B
LED driver (backlight): integrated into Panel
Power Supply (PSU): 168P-P47EEL-W1
MainBoard: 5800-A8M480-0P10
IC MainBoard: EN25Q32
Tuner: ET9Z2E-CF106H
Specifications 47LE61103
AIWA 47LE61103
General repair guidelines for TV LCD LED
Possible malfunctions
- The AIWA 47LE61103 TV does not turn on, does not respond to the remote control and the control panel buttons, does not light up or blink indicators.
In such cases, the 168P-P47EEL-W1 power supply is usually faulty. In the absence of the necessary supply voltages in the secondary circuits of the converters, it is necessary to check the power switches and rectifier diodes for a possible partial or complete breakdown.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during a short circuit in the elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM microcircuits are usually checked by replacement with new ones, or obviously working.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the 5800-A8M480-0P10 motherboard should be started by checking the stabilizers and power converters needed to power the microcircuits and matrix. If necessary, update or replace the software (software). Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the elements of EN25Q32. BGA chip malfunctions are usually easy to detect by warming up.
If the TV works normally from external devices, but does not tune into television channels, the tuner ET9Z2E-CF106H may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
It should be remembered! Attempts to independently repair the TV AIWA 47LE61103, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
FIRMWARE FOR SPI FLASH -----------> AIWA 47LE61103 V1L09, Main: 5800-A8M480-0P10, Panel: LC470EUN (SE)(F1)
The appearance of the MainBoard 5800-A8M480-0P10 is shown in the figure below:
5800-A8M480-0P10
5800-A8M480-0P10 can be used in TVs:
AIWA 47LE61103 (Panel LC470EUN (SE)(F1)), AIWA 42LE6110 (Panel LC420EUN (SE)(M1)), AIWA 39LE6110 (Panel V390HJ1-P01), ERISSON 42LES66 (Panel LC420EUN SEM1), ERISSON 39LES66 (Panel CX275DLEDM), ERISSON 32LES66 (Panel REL320AH-U100 Rev.00), SUPRA STV-LC39660FL (Panel V390HJ1 rev.c1 SEL390V7-S00D ), SUPRA STV-LC32663FL (Panel T320HVN01.2), SUPRA STV-LC39663FL (Panel V390HJ1-P01), SUPRA STV-LC47660FL00 (Panel LC470EUN).
Key Features of AIWA 47LE61103:
Installed matrix (LED-panel) LC470EUN (SE) (F1).
The matrix control uses the Timing Controller (T-CON) 6870C-0401B.
An integrated LED driver is used to power the backlight LEDs.
The necessary supply voltages for all nodes of the TV AIWA 47LE61103 are formed by the power supply module 168P-P47EEL-W1, or its analogs.
MainBoard - the main board (motherboard) is a 5800-A8M480-0P10 module, using EN25Q32 chips and others.
Tuner ET9Z2E-CF106H provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: LG Display
Model: LC470EUN-SEF1
Type: a-Si TFT-LCD, Panel
Diagonal size: 47 inch
Resolution: 1920x1080, FHD
Display Mode: S-IPS, Normally Black, Transmissive
Active Area: 1039.68x584.82 mm
Surface: Antiglare (Haze 1%), Hard coating (2H)
Brightness: 360 cd / m²
Contrast Ratio: 1400: 1
Display Colors: 16.7M (8-bit), CIE1931 68%
Response Time: 6 (G to G)
Frequency: 60Hz
Lamp Type: WLED Embedded (LED Driver)
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V
Trademark: AIWA, Model: 47LE61103.
Short from TV: LCD, LED backlight, 47 ", 1920x1080, 1080p Full HD, 3D, sound: 24W, HDMI: 3.
The composition uses the MainBoard 5800-A8M480-0P10 and the LCD panel (matrix) LC470EUN (SE) (F1).
Power Supply Unit (PSU) 168P-P47EEL-W1 Power Supply.
AIWA 47LE61103 TV with an LCD display LC470EUN, diagonal size 47 "(119 cm) in 16: 9 format. The required brightness of the screen is 360 cd / m² LED backlight LED. Dynamic contrast ratio 120,000: 1 is achieved by special control of the LEDs. In this model Edge LED is used for side lighting. Yes, 2D to 3D conversion
The LC470EUN (SE) (F1) panel and the 5800-A8M480-0P10 motherboard software provide for watching programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphical decomposition according to the standard 1080p (Full HD). The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p.
Supported media file formats: MP3, MKV, JPEG.
The power of the sound system 24 W (2x12 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, VGA, HDMI x3, USB x2. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 1024x768, 1280x1024, 1360x768, 1920x1080.
The power consumed by the TV working in the network mode is 140 watts.
Overall dimensions: 1174x760x166 mm.
TV Weight: 21.1 kg.
Attention! The panel of the LC470EUN (SE) (F1) AIWA 47LE61103 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
