FUSION LED
Model: FLTV-32C10
Chassis / Version: V1N07
Panel: LVW320CSOT E81 V7
LED backlight: LED 4C-LB320T-DS2; 6 * 48 led
LED driver (backlight): integrated into MainBoard; LED DRV = 78v
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 LD7536R
MainBoard: TP.MS18VG.P77 MS82PT
IC MainBoard: CPU: MST3M182VGC-LF-TZ, SPI: 25Q32
Tuner: R620D
Technical Specifications FLTV-32C10
FUSION FLTV-32C10
General repair guidelines for TV LCD LED
The FUSION FLTV-32C10 TV, like many other electronic devices, it is advisable to start repairing by inspecting all external and internal elements. In some cases, visible external damage to the elements can suggest the direction of troubleshooting and localization of the defect even before the start of the necessary measurements at the control points of the nodes of electronic circuits. Swollen electrolytic or cermet capacitors, charred resistors, ring cracks in the soldered terminals of the elements - all this can significantly help the master to determine the causes and consequences of the malfunction of the TV.
In the case when the FLTV-32C10 does not turn on, does not respond to the remote control and buttons on the front panel, does not blink lights and does not show any signs of operability, the power supply module is probably defective in this case. If it is serviceable with such manifestations, it is necessary to check the stabilizer (converter) of the processor power supply on the motherboard. First of all, it is necessary to replace the swollen capacitors of the rectifier filters, if any. If the mains fuse is broken in the power supply, in most cases a breakdown of the power key (s) is detected, which can be integrated with the PWM controller, or a separate field-effect transistor can be used. The rectifier bridge diodes and the electrolytic capacitor of the mains rectifier filter should also be checked.
It should be remembered that in the practice of repair, usually the power switches in switching power supplies (SMPS) do not fail due to their poor quality and, in such cases, it is necessary to look for the cause that led to a malfunction and provoked a breakdown of the key. Most often, the culprits of the accident are dried electrolytic capacitors or dangling resistors in the primary circuit, or the PWM controller chip itself may be faulty. It is also necessary to check all the semiconductor elements of the stabilization circuit in the primary and secondary circuits.
If there is no image when you turn on the FUSION FLTV-32C10, or it appears for a second and disappears, but there is sound, most likely there is a malfunction in the backlight LED circuit of the LVW320CSOT E81 V7 panel, or in their power converter. It is necessary to check the electrolytic capacitors of the filter of the secondary rectifiers in the general power supply unit.
Often there is a need for disassembling the panel to check the health of the LEDs, as well as contact connections in the connectors and soldering.
An open in the LED lines connected in series cannot be detected with a multimeter or tester without disassembling the panel. To open all the transitions, several tens of volts are needed, and it is best to use a current source for such purposes.
Diagnostics and repair of the TP.MS18VG.P77 MS82PT motherboard is carried out by checking the performance of the stabilizers or power converters of the module chips. In some cases, a software update is required.
Board repair and replacement of 25Q32 microcircuits are carried out in the presence of the necessary equipment, and the corresponding element base. Faults associated with the use of BGA processor soldering technologies can be localized by the heating method.
Attention! For users and owners of FLTV-32C10 TVs who do not have the appropriate qualifications, knowledge and experience, we strongly recommend against attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-32C10 V1N07, Main: TP.MS18VG.P77 MS82PT, Panel: LVW320CSOT E81 V7
In case of failures in the software of Winbond SPI FLASH microcircuits, they can for some time restore their performance after temperature exposure - heating the soldering station with a hairdryer or even a lighter. Usually this is enough to read the regular contents of the software. In such cases, the chip must be replaced with a new one.
Repair MainBoardThe appearance of MainBoard TP.MS18VG.P77 is shown in the figure below:
TP.MS18VG.P77
TP.MS18VG.P77 can be used in TVs:
ERISSON 24LET35 (Panel LVW240CMOT E1 V2), ERISSON 19LET35 (Panel M185XTN01.3), FUSION FLTV-24C10 (Panel LVW230SSOT E1 V2), FUSION FLTV-32C10 (Panel LVW320CSOT E81 V7), HYUNDAI H-LED32V19 (Panel LVW320CSOT E45 V10), HYUNDAI H-LED32V23 (Panel LVW320C80T E64 V5), TCL 19T2100 (Panel M185XTN01.2), TELEFUNKEN TF-LED32S23 (Panel LVW320CS0T E146 V1), THOMSON 32B2600 (Panel LVW320C8OT EB1), THOMSON 28B2500 (Panel LVW280CSOT E13V1).
Main features of the FUSION FLTV-32C10 device:
Installed matrix (LED-panel) LVW320CSOT E81 V7.
To power the backlight LEDs, a converter is used, combined with the main board TP.MS18VG.P77, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is designed according to a flyback AC / DC voltage converter using PWM SOT23-6 LD7536R microcircuits.
MainBoard - the main board (motherboard) is a TP.MS18VG.P77 module, using CPU chips: MST3M182VGC-LF-TZ, SPI: 25Q32 and others.
The R620D tuner provides television reception and channel tuning.
FUSION FLTV-32C10 TV with LVW320CSOT LCD display, 32 "(81 cm) diagonal size in 16: 9 format. The required brightness of the screen is 280 cd / m² LED backlighting. Dynamic contrast ratio 80000: 1 is achieved by special control of the LEDs. In The LED panels of this TV are equipped with edge LED backlighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i Supported media file formats: MP3, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
Overall dimensions: with stand 740x504x200 mm, without stand 740x451x115 mm.
TV Weight: with stand: 4.96 kg, without stand: 4.64 kg.
Attention! The LVW320CSOT E81 V7 panel of the FUSION FLTV-32C10 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
