SANYO LCD 47XF5 LCD TV HOW TO ENTER THE SERVICE MODE, DEFAULT SERVICE MODE VALUES, SCHEMATIC DIAGRAM

Service Menu

This set has an On-screen Service Menu System included in the CPU that allows remote operation for most of the service adjustments

On-screen Service Menu System

Quick operation is needed to enter Service Mode.

How to enter the Service Menu
1. Press and hold the MENU button on Side Controls.
2. Keep pressing the MENU button and press the MUTE button on the remote control, and the FACTORY MENU will be displayed.
3. Select SERVICE by pressing (Up) or (Dn) button and then press( +) or ( - ) button to enter SERVICE menu.

How to select the service item and adjust data

1) Select “DATA” line by pressing (Up) or (Dn) button.

2) Press (+) or (-)  button to adjust data

To exit service mode
Press BACK button or MENU button to exit service mode.

Note: The all adjusted data in service mode will be memorized into EEPROM automatically.

Initial data [Default data]

 

Setting the Initial data
This adjustment is controlled by the CPU (IC8000) through the IIC Bus Data Line in the chassis, and those adjustment data are memorized the memory IC (IC8002). Therefore, Main board or the memory IC (IC8002) is replaced, these data will be disappeared. Readjust should be made. Initial data is provided in the CPU ROM, when the memory IC (IC8002) is replaced with new one. CPU ROM data is loaded into the memory. Initial data is provided to operating the monitor basically. For operating the monitor quality performance, further adjustment is required following chassis electrical adjustment.

1. Receive good quality signal.
2. Enter the Service Mode.
3. Confirm data value to be the same as the Service Adjustment Data Table. If it is different, change to correct data
4. Exit the Service Mode.

White balance Adjustment

Picture Mode: STANDARD
Color Temperature: NORMAL
Aging Time: More than 10 minutes

1. Enter the FACTORY MENU.

2. Select WHITE BALANCE by pressing (Up) or (Dn)  button, and then pressing ( + ) or ( - ) button to enter it.

3. To adjust Red : Press 1 (data value up) and 4 (data value down).
To adjust Green : Press 2 (data value up) and 5 (data value down).
To adjust Blue : Press 3 (data value up) and 6 (data value down).

4. Decide one item in three items to a fixed value (For example, let R be fixed value as following picture.), select item of other 2 colors (Example, G or B as following picture), and adjust to produce a normal black and white picture in highlight areas.
(Note: At this time, Adjust the other 2 colors data less than fixed data.)

5. Exit the FACTORY MENU

After adjustment, confirm white balance again by normal picture.

Schematic diagrams

Main board

Power board

 

SANYO RM5500M, PIONEER CT3131, SONY TC95A, GRADENTE DS20, CCE DR1000, , CS930D, CASSETTE DECKS CIRCUIT DIAGRAM [SCHEMATICS]

 Gradente DS20 cassette deck, Gradente spec87 cassette deck, CCE DR1000 cassette deck, CCE CS930D cassette deck, Sanyo RM5500M cassette deck, Pioneer CT3131 cassette deck, Sony TC95A cassette deck

Used ICs: CX 0168, TBA 820M, LA4550, LA7343, LA1260, LA1160

CCE 930D schematic

CCE DR1000 Schematic

Gradente Spect87 Schematic

Gradente  DS20 schematic

Pioneer CT3131 Schematic

Sanyo RM5500M Schematic

Sony TC95A Schematic

LG42LN5200, LG42WT30, LG42WL10 , PANASONIC TH42LRU60, SANYO DP42D23, LGL42L80, LG47GA6400 T-CON BOARDS TIMING CONTROL BOARDS INTERCONNECTIONS SCHEMATICS

 42LN5300 Interconnect:  TV Models: LG 42LN5200 5300 5400 5700, LG 42WT30, LG 42WL10, Panasonic TH-42LRU60, Sanyo DP42D23 P42D23-00 & P42D23-11

PANEL P/N: EAJ62310701

Part Number: 6871L-3403A

T-con Board P/N: 6870C-0452A

DESC or Panel Sticker Number: LC420DUE-SFR5, LC420DUE-SFR1 (similar to LC500DUE-SFR1)

Warning: Be sure to install the screws in the T-CON board before applying power. Damage to the board will occur.

Panel Test: To run the T-CON “Panel Test”, remove the LVDS cables. Jump 12V to the 12V fuse. Jump VCC 3.3V to pin-44 on CN1. White, Red, Blue, Green and Black patterns show on screen.

LG 42LN5300 P1100 (Mainboard) CN1 (T-CON board) Connector Video Waveforms

All LVDS signals are taken with SMPTY Color Bar signal input (1080P)

Component Input. All LVDS signals are “Differential Pairs”. The ones shown are the “Positive” signal of the pair. The Negative signal looks exactly the same but flipped 180 degree. Scope Settings are 100mV per/division, 2.5uSec per/division.

42LV5500 Interconnect:  TV Models: LG 42LV5400, LG 42LV5500, LG 42LW5300

PANEL P/N: EAJ61749101

Part Number: 6871L-2693A

T-con Board P/N: 6870C-0358A

DESC or Panel Sticker Number: LC420EUF-SDA1 (V6 32/42/47 FHD 120Hz)

Warning: T-CON Board under shield. Be to reinsert screws before operating set with shield removed.

PANEL Test:  To run the T-con “Panel Test”, remove the LVDS cables. Jump 12V to the 12V fuse. Jup VCC 3.3V to pin-44 on CN1. White, Red, Blue, Green and Black patterns show on screen.

Note: Before doing the Panel Test, make sure their backlight can lit/operating normally.

 

 

42SL80 Interconnect: TV Models: LG 42SL80

PANEL P/N: EAT60667401

Part Number: 6871L-1828A

T-con Board P/N: 6870C-0259A

DESC or Panel Sticker Number: LC420WUD-SBM4 (42/47 Slim & Narrow 240Hz CONTROL)

47GA6400 Interconnect:  TV Models: LG 47GA6400

PANEL P/N: EAJ62270801

Part Number: 6871L-3264A

T-con Board P/N: 6870C-0444A

DESC or Panel Sticker Number: LC470EUN-SFF2 (DESC: LC470DUE-SFR1)

Warning: Return the screws when servicing the T-CON board with shields removed.

Concerning Quick Start:  If Quick Start is turned on in the Options Menu, T-CON 12V will be available during STBY, but there will be no video to process. Also, no Backlight.

CN2: Global Dimming

(1) Scan 1, (2) Scan 2, (3) Scan 3, (4) GND.  Pins are inverted on inverter.

PANEL Test:  To run the T-CON “Panel Test”, remove the LVDS cable CN1. Jump 12V to the 12V fuse on T-con board. Jump VCC 3.3V to pin-44 on CN1. White, Red, Blue, Green and Black patterns show on screen.

SANYO PLC XW20 HOW TO ENTER THE SERVICE MODE OF 3 LCD PROJECTOR, SCHEMATIC, SERVICE ADJUSTMENTS-HOW TO REPLACE THE LAMP

How to enter the service mode of Sanyo PLC XW20 3LCD projector, schematic, service adjustments-How to replace the lamp

Sanyo Multimedia Projector PLC-XW20, PLC-SW20

(U.S.A., Canada, Europe, Asia, Africa U.K.)

ORIGINAL VERSION Chassis No. MW6-XW2000 (PLC XW20), MZ6 SW2000 (PLC SW20)

Lamp replacement

When the life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow.

When a projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required.

Allow a projector to cool for at least 45 minutes before you open Lamp Cover.
The inside of a projector can become very hot.

Turn off the projector and disconnect AC plug. Allow the projector to cool for at least 45 minutes.
2. Remove a screw with a screwdriver to remove Lamp Cover.
3. Remove 2 screws with a screwdriver and pull out Lamp Assembly by grasping Handle.
4. Replace Lamp Assembly with a new one and tighten 2 screws back. Make sure that Lamp Assembly is set properly. Replace Lamp Cover and tighten a screw.
5. Connect AC Power Cord to the projector and turn it on.
6. Reset Lamp Replace Counter (refer to the section “Lamp Replace Counter” below).

[Do not reset Lamp Replace Counter when Projection Lamp is not replaced]

LAMP REPLACE COUNTER

[Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE Indicator stops lighting.]

1. Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SETTING Menu icon.
2. Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press SET button.  The message "Lamp replace counter reset?" is displayed. Move the pointer to [Yes] and then press SET button.
3. Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.
(Do not reset Lamp Replace Counter except after Projection Lamp is replaced.)

FUSE FOR CIRCUIT PROTECTION

The fuse is located on the ass'y-power. When either the LAMP indicator or the READY indicator is not illuminated, fuse may be opened. Check the fuse as following steps.

Remove the ass'y-power following to “Mechanical Disassemblies”.
2. Remove the fuse from fuse holder.
3. Check the resistance of fuse by using the tester.

To install the fuse, take reversed step in the above.

The temperature monitor system.

The temperature monitor system is provided to prevent damage of component parts inside the projector from overheat. Two protection systems are provided.

Temperature monitor -1 :
When this function operates, warning-temperature-indicator flashes. And cooling fan continues operating until it becomes a normal temperature. If it continue to flush and flash does not stopped, disconnect the AC cord and investigate the cause of overheating.

Temperature monitor -2 : (thermal switch SW902)
This function (thermal switch SW902) will not operate, while the temperature monitor -1 is operating normally. If it has operated, it needs to be reset manually. Disconnect the AC cord first and investigate the cause of overheating.  After servicing, reset the thermal switch (SW902) as shown.

SERVICE ADJUSTMENT

To enter service mode
To enter service mode press the "MENU" and "IMAGE" buttons on the projector simultaneously and hold for 2 seconds. As shown in a figure, a service mode display appears on a screen.

Adjust service data using the following control buttons.
1. "POINT UP" ------- An item number increases.
2. "POINT DOWN" -- An item number decreases.

3. "POINT RIGHT" -- "VOLUME+"

An adjustment value increases.

4. "POINT LEFT" ---- "VOLUME - "

An adjustment value decreases.

To exit the service mode.
Press the "POWER on/off" button only once on the projector or remote control unit to quit the service mode.

SERVICE MODE ADJUSTMENT MENU

[Other adjustment items are not related to service and a maintenance. Don't press the VOLUME (+) and (-) buttons at the time of those adjustment items. Otherwise it may cause loss of product safety]

Fan driving voltage adjustment
1. Enter the service mode.

Set the item no. to [50] by pressing the Point up or down button.

Set the data value to [1] by pressing the Volume + or – button.

2. Set the item no. to [67]. Set the data value to [1].

3. Adjust the voltages of TP66A to 8.4 ± 0.1 V-DC by the VR5601.

4. Set the item no. to [50]. Set the data value to [0].

5. Set the item no. to [67]. Set the data value to [1].
NRS adjustment

Signal center DC adjustment.

Enter the service mode.

Adjust each values of below test point to be minimum amplitude by volume + or – buttons.

Contrast adjustment

Schematic

SANYO LCD 47XR2 SMPS SCHEMATIC, FACTORY MODE, SOFTWARE UPDATE

LCD 

1 682 342 81 : AUS, SS etc. 

1 682 343 78 : INDIA

Method of software upgrading
Steps of software upgrading are as follows
1. Select a serial connection wire and a VGA connection wire and then connect them by means of a patch panel;
2. Use a serial wire to connect the PC to the patch panel and set TV set to off state; Open the software upgrade file folder and double click FlashUpgrader.exe (window 2000/XP/NT)
The following interfaces will show up after running the program.

Based on the computer features, set up the serial port (COM Port). 

Select corresponding serial port (if it’s unable to FLASH WRITE, change to another port). 

Baud is selected to be 115200. 

Then select Reset Target After Download. 

Click FLASH push-button, it’s ready to run. 

For other settings, please refer to the Fig. Above (already defaulted by the system, normally no need to change).
Switch on TV set the FLASH write program begins to run;

When the upgrading is complete, a window (below) will be opened. 

Press “Finish” button to complete the process.

Note: Do not shut the power off or turn the TV set on during the FLASH write. Otherwise it may lead to no way for flash to rewrite.

To Enter the factory menu  press 1→ 9 → 7 →9 button in the window menu state.

The unit has two MCU, the main MCU is PW218 (N601): it is used to control all the chips’ working status on the main board (including image processing, channel switch, sound processing, image display etc.), sub CPU, OSD, searching channels, image effect adjustment, buttons control, infrared remote control etc.; the sub CPU is ATMEGA8L (N606): it is used to control power supply, including standby and turning on the unit by using remote control etc.. The two MCU correlates with each other through pin 14 INT (interruption) of ATMEGA8L, pin 28 and 29 SDA, SCL.
The unit has one integrative tuner (including HF and IF amp. circuits). 

The signal received by antenna is sent to tuner, under the control of MCU PW218 (N601) SDA and SCL, proper channel selection and right system switching will be done by the tuner, then video signal and audio signal will be output by the tuner through decoding and by high and intermediate amplification. Video signal of the tuner will then be sent to Decoder PW2300 (N201). Audio signal of the tuner will then be sent to AV switch box M52797 (N400), the audio signal of AV1, AV2 and HD2 of the main board will also be sent to M52797 (N400) at the same time. The selected audio signal after switching will be sent to R2S15900 (N301), and then switching selection will be done towards the above audio signal together with the audio signal of VGA, HDMI and HD1. The two chips are controlled by PW218 (N601), after the above process the finally selected way will be set to X300 earphone socket after under the control of volume, treble and bass which is finished by R2S15900 (N301), the earphone socket has the switching function, when earphone is plugged, sound will be sent to earphone amplifier NJW1109 (N302), then sent back to earphone socket after power amplification.
If earphone is unplugged, sound will be sent to sound amplifier TPA3008 to do amplification and then sent to speaker. Image parts:
Video signal of the tuner will be sent to AV switch box M52797 (N400), video signal of AV1 and AV2 will also be sent to M52797 (N400) at the same time, two groups of video output will be obtained after switching, one group of video output together with its audio output will be sent to AV_OUT terminal to treat as AV OUT. The other group of video output together with other video signals such as S-VIDEO, YpbPr1, YpbPr2 and VGA will be sent to PW2300 to do video decoding or AD transformation, then output 24bit digital RGB signal and some corresponding synchronous signals.
Items such as 3D comb filter, channel switching, 5 lines Y/C separation and color decoding etc. are primarily done by PW2300. 24bit digital RGB signal and some corresponding synchronous signals outputted by PW2300 will then be sent to PW218 (N601). HDMI signal will also be sent to AD9398 (N101) to de decode and output 24bit digital RGB signal as well as some corresponding synchronous signal, which will be sent to PW218 (N601). 

PW218 is a new generation chip of Pixelworks, which has ability to deal with images, 24bit digital RGB signal and some corresponding synchronous signals outputted by AD9398 and PW2300 will be sent to this chip to deal with images.
The chip has functions such as converting from interleaved into line-by-line and image enhancement etc.. PW218 has SCALER function which can do format conversion towards different input formats so as to meet the format needs of the screen and finally output 24bit RGB signal. The interface standard of PDP screen is generally LVDS (low voltage differential signal), so the digital RGB signal outputted from PW218 is needed to send to converting interface chip N6 DS90C387 of LVDS to obtain LVDS signal, then it will be sent to the screen. PW218 is also the main CPU, its programs are stored in periphery device flash N701, and software upgrade through RS-232 interface is virtually upgrading the stored programs through PW218 towards N701.

High definition 1080P LCD
16:9 wide screen
Support several kinds of HDTV wide voltage range, low standby power consumption (less than 1W)
One group of D-SUB, S-VSH (Y/C), RS232, AVOUT, HEADPHONE, HDMI, two groups of YPbPr/YCbCr, AV

SMPS Schematic

SANYO CE20LM5 UK6-A COLOR MONITOR-HOW TO ENTER THE SERVICE MODE, ADJUSTMENT DETAILS

CE20LM5 UK6-A Sanyo Color Monitor-How to enter the service mode, adjustment details

Television system: System I;  Color system: PAL/NTSC4.43 (PAL/NTSC4.43/NTSC3.58 IN AV MODE)

Service Menu

With the set turned ON, press the following sequence of buttons on the remote control:- [MENU, 3, 6, 0, 9]

The main service menu will be displayed.

Model Option:

B/S [Betting Shop]:  For models fitted with SCART and TUNER

CCTV [Closed Circuit TV]: For models fitted with BNC IN/OUT

 Changing the model option will automatically alter some of the settings to suit
the requirements of the application.

Also some menu's & options will not be accessible in the CCTV mode

Hotel Menu

Hotel mode allows the owner to restrict the functionality of the set so that the user may not tamper with settings such as channel tuning.

Volume max' allows the owner to set a limit to the maximum sound output to prevent noise disturbance.

To enter the Hotel Menu press & hold the GREEN button on the remote for about 5 seconds,
the Hotel menu will appear at the bottom of the screen.

Turn ON to disable RF channel tuning facility.

set value between 0 and 100 to limit the sound output available from speaker set the desired input or channel that will appear at switch on.

Use P+ / P- to select item and Vol+ / Vol- to change data.

Option Menu

This menu is used to enable or disable certain functions availible in the bios.
To enter the Option menu press and hold the GREEN button on the remote for about 5 secs, first the HOTEL menu will appear. Now press and hold GREEN for a further 5 secs, now the OPTION menu
will appear. Only the highlighted items may be accessed by the user.

Use P+ / P- on the remote to highlight the desired item, then use Vol+ / Vol-- to change the state.

Other Menu

This menu contains some items that should not normally require adjustment.

Use P+ / P- to select item & Vol+ / Vol-to change value.

ADC Calibration

The ADC ADJ menu is accessible from the main service menu.

ADC calibration is performed automatically by pressing Vol + key whilst the ADC menu is displayed.

A test signal of RGB colour bars must be applied to the SCART input for this adjustment to be performed. If the result is successful, OK will be displayed at the bottom of the OSD.

It is not possible to manually adjust these values.

Press Vol +to begin auto Calibration.

This adjustment is not required for the CCTV model.

Color Temperature

The Color Temperature menu is accessible from the main service menu and is used to adjust the pictures' white balance.

Connect a 100% white test signal to either SCART or Aerial input and set picture mode to STANDARD
Enter the service mode & select Color Temperature option.

Keeping one color constant, adjust R, G, B Gain value to achieve a pure white image.

If a suitable color analyzer is available adjust the co-ordinates to X= 0.290, Y= 0.290 (+/- 0.01).

If the Grey scale suffers from a predominant tint use the R, G, B Offset adjustment to neutralize, in this case the white level adjustment should be re-checked.

Use P+ / P- to select item and Vol+ / Vol- to change value.

Picture Mode

The predetermined settings for the fixed picture modes can be adjusted using this Menu.
Select the PIC Mode desired to be changed using P+ / P- and Vol+ / Vol-change the value as required.

Source: SCART
PIC Mode: Standard
Contrast 42
Brightness 48
Color 45
Sharpness 42

Text Brightness

The three predetermined levels set for Teletext brightness control can be adjusted in this menu.

Use P+ / P- to select item & Vol+ / Vol-to change value.

MAX 63
MID 42
MIN 21

Factory Reset

In certain circumstances it might be useful to restore the memory to the default conditions
preset within the system bios.
To do this enter the main factory menu and select the "Factory Reset" option.
Press vol+ to proceed with the initialization.
This reset does not affect the ADC calibration or the White balance adjustment settings,
nor does it clear the stored RF channels.

OPTIONS & SETTINGS

The table below shows the correct factory settings for this model.
Some of these items may need to be restored if a ‘Factory Reset’ is performed.