REPAIR / SERVICING TV SAMSUNG UE22F5000

Technical description and composition of the SAMSUNG UE22F5000 TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE22F5000 UE22F5000AK
Panel: M215HW03 V.1
T-CON: M215HW03 V1 21M03-C07
LED driver (backlight): integrated into MainBoard
Power Supply (PSU): BN44-00592A A3514 14V 2.5A // BN44-00394C PA-1031-21
MainBoard: BN41-01987A - BN94-06755T
IC MainBoard: SENK13, K4B1G1646G, TPS54328, DRV612, LSC5013R, NTP-7412S, 25Q40CLSIP, K9F1G08U0D, TPS54327, C4435SS, S24C02, S24C2S, LD1117AC
Tuner: BN40-00261A DNTS403EL105A
Technical Specifications UE22F5000
SAMSUNG UE22F5000
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE22F5000 TV does not turn on, does not respond to the remote control and control panel buttons, does not blink with any indicators.
Most often, with such manifestations, the main power module BN44-00592A is found to be faulty. Then it is necessary to measure its secondary (output) voltages and, if they are absent, it is necessary to check the serviceability of power switches and rectifier diodes of the converters for a possible short circuit.
In case of breakdowns of diodes in the secondary circuits, the converter can operate in emergency short circuit mode without output voltages, and during short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor at the source of the key usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, power supply, frequency-setting, damper ... as well as elements of the Negative Stabilization Feedback. The PWM chip can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts is required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as an indicator of serviceability. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-01987A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). When repairing an MB board, you need to check its components SENK13, K4B1G1646G, TPS54328, DRV612, LSC5013R, NTP-7412S, 25Q40CLSIP, K9F1G08U0D, TPS54327, C4435SS, S24C02, S24C2S, LD1117AC. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
If there is no reception of television channels, but the TV works properly from external devices, first of all you need to check the voltage of the tuner BN40-00261A DNTS403EL105A and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
Owners and users of the SAMSUNG UE22F5000 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!

The appearance of the MainBoard BN41-01987A is shown in the figure below:
BN41-01987A
BN41-01987A can be used in TVs:
SAMSUNG UE28F4020AW (Panel HF280AGH-R1), SAMSUNG LT27C370EX (Panel LTM270HL01), SAMSUNG UE22F5000 UE22F5000AK (Panel M215HW03 V.1), SAMSUNG UE28F4000 UE28F4000AW-C1 H2.
The appearance of the power supply
Main features of the SAMSUNG UE22F5000 device:
Installed matrix (LED-panel) M215HW03 V.1.
The matrix control uses the Timing Controller (T-CON) M215HW03.
To power the backlight LEDs, a converter is used, combined with the main board BN41-01987A.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE22F5000 TV is carried out by the BN44-00592A power module, or its analogues.
MainBoard - the main board (motherboard) is a BN41-01987A module using SENK13, K4B1G1646G, TPS54328, DRV612, LSC5013R, NTP-7412S, 25Q40CLSIP, K9F1G08U0D, TPS54327, C4435SS, S24C02, S24C02 microcircuits.
The tuner BN40-00261A DNTS403EL105A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: M215HW03 V1QA
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC)
Response Time: 3.8 / 1.2 (Tr / Td)
Frequency: 60Hz
Lamp Type: 16S4P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V

REPAIR / SERVICING TV SAMSUNG UE22ES5030W

Technical description and composition of the SAMSUNG UE22ES5030W TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE22ES5030W
Chassis / Version: U71B / Ver: AQ02
Panel: M215HW03 V.1
LED driver (backlight): integrated into PSU; 52.8V 0.1A
PWM LED driver: MAP3204C
MOSFET LED driver: AP9997GH
Power Supply (PSU): BN44-00505B - 23A0Q PD23A0QV_CPN
PWM Power: 3BR1065JF
MOSFET Power: 9967GH
MainBoard: BN41-01798A
IC MainBoard: CPU: SEMS23; DRAM: K4B1G1646G; NAND Flash: K9F1G08U0D; EEPROM: 24C256; SOUND: NTP-7412S
Tuner: BN40-00231A
Control: IR: BN41-01828A - UE4000_CEM1
Appearance
SAMSUNG UE22ES5030W
General repair guidelines for TV LCD LED
In the absence of any signs of operability, when the SAMSUNG UE22ES5030W does not turn on and does not signal anything with the control lights on the panel, there is a possibility of a malfunction of the 23A0Q power supply module of the TV. It is advisable to start the troubleshooting of the power supply module by checking the state of the electrolytic capacitors of the rectifier filters and the mains fuse. Defective capacitors should be replaced. If the mains fuse is broken, it is necessary to check first of all the power semiconductor elements - rectifier diodes and 9967GH transistors, which are often found in such a state of breakdown in such situations.
The breakdown of the power switch of the pulse converter is often triggered by other elements, for example, in the stabilization or control circuits of this switch, as well as by the damper elements in its drain and TPI winding.
Sometimes the SAMSUNG UE22ES5030W TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a possibility of a malfunction of the LED driver - the power converter of the backlight LEDs of the M215HW03 V.1 panel, or an open circuit in the LED circuit is possible. In such cases, first of all, it is necessary to verify the operability of the electrolytic capacitors of the filter by supplying the backlight unit.
Often there is a need for disassembling the panel to check the health of the LEDs, as well as the contact connections in the connectors and soldering.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Usually, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
Repair or diagnostics of the BN41-01798A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update the software (software).
Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Checking or replacing CPU elements: SEMS23; DRAM: K4B1G1646G; NAND Flash: K9F1G08U0D; EEPROM: 24C256; SOUND: NTP-7412S requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can be diagnosed by warming up.
The malfunction of the tuner BN40-00231A is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Once again, remind users! Attempts to self-repair a SAMSUNG UE22ES5030W TV without the appropriate qualifications and experience can lead to its complete non-repairability!

SCHEMATIC ----------->  Samsung UE22ES5030W shassis U71A, U71B.
UE32EH5****, UE22ES5****, UE37EH5**** UE19ES4****, UE40EH5****, UE46EH5****, UE26EH4****, UE32EH4****

 The appearance of the MainBoard BN41-01798A is shown in the figure below:
BN41-01798A
BN41-01798A can be used in TVs:
SAMSUNG UE22ES5030W (Panel M215HW03 V.1), SAMSUNG UE22ES5000W (Panel M215HW03 V.1), SAMSUNG UE19ES4000W UE19ES4000 (Panel HT185WX-300).
The appearance of the power supply
Main features of the SAMSUNG UE22ES5030W device:
Installed matrix (LED-panel) M215HW03 V.1.
To power the backlight LEDs, a converter is used, combined with the power supply, controlled by the MAP3204C PWM controller. As power elements of the LED driver, keys of the type AP9997GH are used.
The necessary supply voltages for all nodes of the SAMSUNG UE22ES5030W TV are generated by the BN44-00505B power module or its analogs using 3BR1065JF microcircuits and 9967GH type power switches.
MainBoard - the main board (motherboard) is a BN41-01798A module, using CPU chips: SEMS23; DRAM: K4B1G1646G; NAND Flash: K9F1G08U0D; EEPROM: 24C256; SOUND: NTP-7412S and others.
The tuner BN40-00231A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: M215HW03 V1QA
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC)
Response Time: 3.8 / 1.2 (Tr / Td)
Frequency: 60Hz
Lamp Type: 16S4P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V

REPAIR / SERVICING TV SAMSUNG UE22ES5000W

Technical description and composition of the SAMSUNG UE22ES5000W TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE22ES5000W
Chassis / Version: U71B / Ver: AQ02
Panel: M215HW03 V.1
T-CON: M215HW03 V1 CTRL BD 21M03-C07
LED driver (backlight): integrated into PSU; 52.8V 0.1A
PWM LED driver: MAP3204C
MOSFET LED driver: 9997GH
Power Supply (PSU): BN44-00505B - PD23A0QV_CPN 23A0Q
PWM Power: 3BR1065JF
MainBoard: BN41-01798A BN94-06961M
IC MainBoard: CPU: SEMS23; DRAM: K4B1G1646G; NAND Flash: K9F1G08U0D; EEPROM: 24C256; SOUND: NTP-7412S
Tuner: BN40-00231A
Appearance
SAMSUNG UE22ES5000W
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE22ES5000W does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
Sometimes, in such cases, the BN44-00505B power module is faulty. It is necessary to measure its output voltages, and in case of their absence, it is necessary to check the serviceability of the power switches of the converters and rectifier diodes for the probability of a short circuit.
In case of breakdowns in breakdowns of diodes in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key usually breaks.
PWM (PWM) 3BR1065JF, if there is no open fault between the terminals, it is checked by replacing with a known-good one.
- There is no image, there is sound, there is a reaction to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
In most cases, a malfunction is caused by a lack of display backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a malfunction, the zener diode PN junction will either be cut off or broken into short-circuit.
- The indicator blinks or glows constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-01798A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Board repair and replacement of CPU chips: SEMS23; DRAM: K4B1G1646G; NAND Flash: K9F1G08U0D; EEPROM: 24C256; SOUND: NTP-7412S are manufactured with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
If a tuner BN40-00231A is suspected of malfunction, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary supply voltage levels and data exchange pulses with the processor via the I2C bus at the corresponding tuner pins.
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair to professionals with sufficient experience in the repair of electronic equipment.


SCHEMATICS ------------>  Samsung UE22ES5000W shassis U71A, U71B.
UE32EH5****, UE22ES5****, UE37EH5**** UE19ES4****, UE40EH5****, UE46EH5****, UE26EH4****, UE32EH4****

 The appearance of the MainBoard BN41-01798A is shown in the figure below:
BN41-01798A
BN41-01798A can be used in TVs:
SAMSUNG UE22ES5030W (Panel M215HW03 V.1), SAMSUNG UE22ES5000W (Panel M215HW03 V.1), SAMSUNG UE19ES4000W UE19ES4000 (Panel HT185WX-300).
The appearance of the power supply
Main features of the SAMSUNG UE22ES5000W device:
Installed matrix (LED-panel) M215HW03 V.1.
The matrix control uses the Timing Controller (T-CON) M215HW03.
To power the backlight LEDs, a converter is used, combined with the power supply, controlled by the MAP3204C PWM controller. As power elements of the LED driver, keys of the type 9997GH are used.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE22ES5000W TV is carried out by the BN44-00505B power module, or its analogs using 3BR1065JF microcircuits.
MainBoard - the main board (motherboard) is a BN41-01798A module, using CPU chips: SEMS23; DRAM: K4B1G1646G; NAND Flash: K9F1G08U0D; EEPROM: 24C256; SOUND: NTP-7412S and others.
The tuner BN40-00231A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: M215HW03 V1QA
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC)
Response Time: 3.8 / 1.2 (Tr / Td)
Frequency: 60Hz
Lamp Type: 16S4P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V

REPAIR / SERVICING TV SAMSUNG UE22D5003

Technical description and composition of the SAMSUNG UE22D5003 TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE22D5003
Chassis / Version: U57B
Panel: LTM215HT04-V (BN07-01044A)
PWM LED driver: LED Controller - OZ9998
MOSFET LED driver: STM4886
Power Supply (PSU): BN44-00467A
PWM Power: GM0765R
MOSFET Power: GM0765R
MainBoard: BN41-01703A
IC MainBoard: SPI Flash: 25X40BVSIC, EEPROM: 24C256, NTP-7411S
Tuner: DTM-8B 125S
Technical Specifications UE22D5003
SAMSUNG UE22D5003
General repair guidelines for TV LCD LED
Diagnostics of malfunctions and repairs SAMSUNG UE22D5003, as well as other electronic devices, it is recommended to start with an external examination of the external and internal elements. It often happens that visible damage to elements or connections helps determine the direction of the troubleshooting. Elements with visible damage, for example, capacitors swelled up after boiling the electrolyte, charred resistors in certain nodes of the circuit, as well as ring cracks in solders will help the master to guess the causes and possible consequences of the malfunction.
If the TV does not turn on, no indicators on its front panel are lit or blinking. Also, if the TV does not respond to the remote control and buttons, it does not make any sounds or any signs of operability when it is turned on, there is a certain chance that the BN44-00467A power module is defective and needs repair. Sometimes with similar manifestations a problem can only occur in the absence of processor power, which is typical for certain SAMSUNG models. First of all, it is necessary to replace the swollen capacitors of the rectifier filters, if any. If the mains fuse is broken in the power supply, in most cases a breakdown of the power key (s) of the GM0765R is detected, which can be integrated with a PWM controller, or a separate field-effect transistor can be used. The rectifier bridge diodes and the electrolytic capacitor of the mains rectifier filter should also be checked.
If a breakdown of the power switch is detected, it should be remembered that in a switching power supply (IIP) it does not fail by itself for no reason that you should look for when checking other elements of the primary circuit - electrolytic capacitors, PWM controller GM0765R, which can be checked only by replacement, as well as other semiconductor elements (diodes, transistors, zener diodes).
If the SAMSUNG UE22D5003 TV does not have an image, but there is sound, a malfunction in the LED backlight circuits of the BN07-01044A panel is likely. It is also necessary to check the serviceability of the electrolytic capacitors of the filter of the secondary rectifiers of the BP (power supply) for an overstated ESR.
To check the health of the LEDs, as well as contact connections in the ruler circuit, it is necessary to disassemble the panel.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source.
In cases of attempts to repair the motherboard BN41-01703A, it is necessary to check the operability of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating.
In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its percent-ic301 chips - NTP-7411S Flash-25X40BVSIC 24C256 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Before replacing the DTM-8B 125S tuner, if there is no tuning for the channels, you must first check the supply voltage at its terminals, including the power supply of varicaps (30-33V).
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair only to professionals with sufficient experience in the field of repair of electronic equipment.

SCHEMATICS ----------> Samsung UE22D5003 Chassis U57B.

Chassis : U66A Model : UE32D55**R*, UE37D55**R*, UE40D55**R*, UE46D55**R*, UE32D57**RS, UE37D57**RS, UE40D57**RS, UE46D57**RS
Chassis : U57A Model : UE32D50**PW, UE37D50**PW, UE40D50**PW, UE46D50**PW, UE32D40**NW
Chassis : U57B Model : UE19D40**NW, UE22D50**NW, UE27D50**NW.


 The appearance of the MainBoard BN41-01703A is shown in the figure below:
BN41-01703A
BN41-01703A can be used in TVs:
SAMSUNG UE19D4003BN UE19D4003BW (Panel LTM185AT05), SAMSUNG UE22D5003 (Panel LTM215HT04-V (BN07-01044A)).
The appearance of the power supply
Main features of the SAMSUNG UE22D5003 device:
Installed matrix (LED panel) LTM215HT04-V (BN07-01044A).
A converter controlled by the PWM controller LED Controller - OZ9998 is used to power the backlight LEDs. As power elements of the LED driver, keys of the STM4886 type are used.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE22D5003 TV is carried out by the BN44-00467A power module, or its analogs using GM0765R microcircuits and GM0765R type power switches.
MainBoard - the main board (motherboard) is a BN41-01703A module, using SPI Flash chips: 25X40BVSIC, EEPROM: 24C256, NTP-7411S and others.
The DTM-8B 125S tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTM215HT04-V
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 72%
Response Time: 5 (Tr + Td)
Frequency: 60Hz
Lamp Type: 10S3P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V

REPAIR / SERVICING TV SAMSUNG UE32H6410AU

Technical description and composition of the SAMSUNG UE32H6410AU TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32H6410AU UE32H6410
Chassis / Version: Ver: TH01
Panel: CY-GH032CSLV4V
LED backlight: 32F-A BN41-02170A + 2014SVS32FHD_3228_07_REV1.1 131108NHF
T-CON: BN95-01307A - 32H6200-6410 - BN95-01326A
LED driver (backlight): integrated into PSU; 30V, 60V 1100 mA
PWM LED driver: PIC16F753, 7014X * 3
MOSFET LED driver: MDD7N25, FDD6N25 * 2
Power Supply (PSU): BN44-00707A L32X1T_EHS HU10123-14058
PWM Power: SPC7011F (PFC), FA6A01 (PWM SOP-16)
MOSFET Power: 10N60M2 (PFC), KF7N50 * 2
MainBoard: BN41-02156A - BN94-07548E
IC MainBoard: CPU: SEMS31; SPI Flash: 25Q40CL; EEPROM: S24C512; SOUND: NTP7414
Tuner: BN40-00288A
Control: IR: BN41-02151A UH5500_IR REV 1.9, WiFi: WIDT30Q BN59-01174A
Technical Specifications UE32H6410
SAMSUNG UE32H6410AU
General repair guidelines for TV LCD LED
If the UE32H6410AU TV does not turn on, does not make any sounds when it is turned on, and also no indicators on the front panel light or blink, there is a high probability of a malfunction in the power supply module. In some cases, there may be a malfunction only in standby power. When diagnosing and repairing the power supply, first of all, replace the swollen filter capacitors of the secondary rectifiers and check the fuse and, if it is broken, it is necessary to identify the cause. Often in such cases, an avalanche (thermal) breakdown is detected in the power semiconductor elements of the module — rectifier diodes and transistors in the primary circuit.
As a rule, the keys in switching power supplies (SMPS) are reliable enough and rarely fail for no reason to be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM chip is checked by replacing it with a known good one.
If the SAMSUNG UE32H6410AU TV does not have an image, but there is sound, a malfunction in the backlight circuits of the LED panel CY-GH032CSLV4V is likely.
In case of breaks in the LED circuit, a complete disassembly of the panel is required, the LEDs are checked for breakage, as well as the reliability of the connections in the connectors and the rations of the terminals.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Usually, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
If the motherboard BN41-02156A - BN94-07548E is faulty, first of all it is necessary to check all the linear stabilizers and power converters of its chips, and also, if necessary, update the software (software). Sometimes you can check the health of MB only by replacement.
In some cases, to repair the MB board (SSB), it may be necessary to replace the chips - CPU: SEMS31; SPI Flash: 25Q40CL; EEPROM: S24C512; SOUND: NTP7414 to new or obviously working. In cases where BGA technologies are used, defects are usually localized by the heating method.
If there is no reception of television channels, but the TV is working properly from external devices, first of all, check the voltage of the tuner BN40-00288A and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
We recommend the owners of the UE32H6410AU TV for repair only to qualified specialists with experience! Self-repair attempts without the appropriate knowledge and skills can lead to serious negative consequences!

The appearance of the MainBoard BN41-02156A is shown in the figure below:
BN41-02156A
BN41-02156A can be used in TVs:
SAMSUNG UE40H6200 UE40H6200AK (Panel CY-GH040CSLV1V), SAMSUNG UE32H5500 UE32H5500AK (Panel GH032BGA-B2), SAMSUNG UE40H5500 UE40H5500AK (Panel CY-GH040BGLV2V), SAMSUNG UE32H6200AK (Panel CY-GH032CSLV1V), SAMSUNG UE40H6350 (Panel CY-GH040CSLV2V), SAMSUNG UE32H6410AU UE32H6410 (Panel CY-GH032CSLV4V), SAMSUNG UE40H6400AK UE40H6400 (Panel CY-SH040CSL V2H), SAMSUNG UE48H6200 UE48H6200AK (Panel CY-GH048CSLV1V), SAMSUNG UE48H6230AK UE48H6230 (Panel CY-GH048CSLV1V), SAMSUNG UE48H6400AK UE48H6400 (Panel CY-GH048CSLV2V), SAMSUNG UE48H6410AU UE48H6410 (Panel CY-GH048CSLV4V), SAMSUNG UE48H6240AK UE48H6240 (Panel CY-GH048CSLV1V), SAMSUNG UE32H4500AK UE32H4500 (Panel CY-HH032AGLV2V), SAMSUNG UE40H6410 UE40H6410AU (Panel CY-GH040CSLV4V), SAMSUNG UE40H6500 UE40H6500AT (Panel CY-GH040CSLV1V), SAMSUNG UE32H6230 UE32H6230AK (Panel T320HVF05.2), SAMSUNG UE32H4510 UE32H4510AK (Panel HH032AGH-R3 BN96-31086F), SAMSUNG UE32H6350 UE32H6350AK (Panel CY-GH032CSLV2V), SAMHUN62H3062G3062 CY3062CG6262 SLV1V).
The appearance of the power supply
Main features of the SAMSUNG UE32H6410AU device:
Installed matrix (LED panel) CY-GH032CSLV4V.
The matrix control uses the Timing Controller (T-CON) BN95-01307A.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by a PIC16F753, 7014X * 3 PWM controller. As power elements of the LED driver, keys of the type MDD7N25, FDD6N25 * 2 are used.
The necessary supply voltages for all nodes of the SAMSUNG UE32H6410AU TV are generated by the BN44-00707A power supply module or its analogs using microcircuits SPC7011F (PFC), FA6A01 (PWM SOP-16) and power switches of the type 10N60M2 (PFC), KF7N50 * 2.
MainBoard - the main board (motherboard) is a BN41-02156A module, using CPU chips: SEMS31; SPI Flash: 25Q40CL; EEPROM: S24C512; SOUND: NTP7414 and others.
The tuner BN40-00288A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J4000AK

Technical description and composition of the SAMSUNG UE32J4000AK TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J4000AK UE32J4000
Panel: JJ032AGH-R1
LED backlight: 2015 SVS F-COM 32 HD L5 REV1.4 150518 LM41-00133A_LM41-00148A
T-CON: 8T3151A04-8 VER.2.1
LED driver (backlight): integrated into MainBoard
PWM LED driver: BD9397EFV
Power Supply (PSU): A4819_FDY Adapter 19V 2.53A
MainBoard: BN41-02358B BN94-08202A
IC MainBoard: NAND: F59L1G81A-25TI, DDR: K4B2G1646Q-BCK0, FLASH: W25Q40CLSIP, EPRROM: S24C256
Tuner: BN40-00316A
Control: BN96-36076G J4003 BN41-02398A
Appearance
SAMSUNG UE32J4000AK
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE32J4000AK does not turn on at all. The control lights do not light or flash. On the remote control and the buttons on the control panel does not respond.
In such cases, the fault should be sought first in the power supply module A4819_FDY.
The owner of a TV can purchase an external power supply unit such as A4819_FDY and repairing it is not always advisable. In any case, the simplest typical defects characteristic of most IIP schemes can be easily detected and eliminated after opening. It is necessary to measure its secondary output voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, power supply, frequency-setting, damper ... as well as elements of the Negative Stabilization Feedback. The PWM chip can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn on and immediately disappears
Often in such cases, there is no LED backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a malfunction, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-02358B motherboard should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, you should update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the health of its elements - NAND: F59L1G81A-25TI, DDR: K4B2G1646Q-BCK0, FLASH: W25Q40CLSIP, EPRROM: S24C256 which may require replacement with new ones. If the BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
Before changing the tuner BN40-00316A, if it is not possible to tune to television channels, you should make sure that there are supply voltages that must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
TV users and owners need to remember that attempts to self-repair a SAMSUNG UE32J4000AK TV without the appropriate qualifications and necessary experience can lead to serious negative consequences!

UE32J4000AW - Panel: JJ032AGH-R1, MainBoard: BN41-02358A BN94-08202C

 The appearance of the MainBoard BN41-02358B is shown in the figure below:
BN41-02358B
The appearance of the power supply
Main features of the SAMSUNG UE32J4000AK device:
Installed matrix (LED-panel) JJ032AGH-R1.
The matrix control uses the Timing Controller (T-CON) 8T3151A04-8.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02358B, controlled by the BD9397EFV PWM controller.
An external source such as A4819_FDY Adapter 19V 2.53A is used to power all internal components of the SAMSUNG UE32J4000AK TV.
MainBoard - the main board (motherboard) is a BN41-02358B module, using NAND chips: F59L1G81A-25TI, DDR: K4B2G1646Q-BCK0, FLASH: W25Q40CLSIP, EPRROM: S24C256 and others.
The tuner BN40-00316A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J4100

Technical description and composition of the SAMSUNG UE32J4100 TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J4100 UE32J4100AU
Chassis / Version: LF07
Panel: HH032AGS-R1
LED backlight: LM41-00099M
T-CON: RUNTK DUNTK 5524TP ZA
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00700A L32S1_EDY
PWM Power: 3S111
MOSFET Power: K10A60W, MBRF10150CTL
MainBoard: BN41-02098B BN94-09059S
IC MainBoard: F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414
Tuner: BN40-00294A
Control: BN41-01976B BN96-30857C
Technical Specifications UE32J4100A
SAMSUNG UE32J4100
General repair guidelines for TV LCD LED
Possible malfunctions
- The SAMSUNG UE32J4100 TV does not turn on and does not show any signs of turning on, it does not respond to the control buttons or the remote control.
Often in such cases, the BN44-00700A power module is faulty. It is necessary to measure its output voltages and, if they are absent, to check for short-circuit probabilities in the converters, power switches (K10A60W, MBRF10150CTL) and rectifier diodes.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) 3S111, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
Often in such cases, there is no LED backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). When repairing an MB board, it is necessary to check its components F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
Before replacing the tuner BN40-00294A, if there is no tuning to the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Attention to users! Self-repair of a SAMSUNG UE32J4100 TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!

The appearance of the MainBoard BN41-02098B is shown in the figure below:
BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel CY-JJ040BGNV2V), SAMSUNG UE40H5020 UE40H5020AK (Panel CY-GH040BGSV1V), SAMSUNG UE40J5100AU (Panel CY-GH040BGSR1V), SAMSUNG T31D310EW (Panel CY-HH032AGSV1H), SAMSUNG UE48J5000AU (Panel CY-JJ048BGEV5V), SAMSUNG UE32H5020AK (Panel CY-GH032BGLV4V), SAMSUNG UE40J5120AU (Panel CY-GH040BGSV1V), SAMSUNG LT32E310EX T32E310EX (Panel CY-GJ032BGEV1V), SAMSUNG UE40H5270 UE40H5270AU (Panel CY-GH048BGLV1V), SAMSUNG UE32J5100AK UE32J5100 (Panel CY- GH032BGSV1V), SAMSUNG UE32H5000AK UE32H5000 (Panel CY-GH032BGLV1V), SAMSUNG UE48H5000 UE48H5000AK (Panel CY-GH048CSLV1V), SAMSUNG UE32J5120AK UE32JSV1B (CY.
The appearance of the power supply
Main features of the SAMSUNG UE32J4100 device:
Installed matrix (LED-panel) HH032AGS-R1.
The matrix control uses the Timing Controller (T-CON) RUNTK.
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the SAMSUNG UE32J4100 TV are generated by the BN44-00700A power module or its analogs using 3S111 microcircuits and power switches of the K10A60W, MBRF10150CTL type.
MainBoard - the main board (motherboard) is a BN41-02098B module, using chips F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 and others.
The tuner BN40-00294A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J4500

Technical description and composition of the SAMSUNG UE32J4500 TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J4500 UE32J4500AK
Chassis / Version: CA02
Panel: CY-JJ032AGHVEV
LED backlight: SVS32 HD FCOM 5LEDS REV2.2 160925 LM41-00463A
T-CON: ST3151A05-E-XC-2; CSH11-C0H, BBA7SH, GT432B-2ZL
LED driver (backlight): integrated into MainBoard
PWM LED driver: BD9397EFV
Power Supply (PSU): Adapter 19V
MainBoard: BN41-02360B BN94-08207F
IC MainBoard: S24C256, DRV612, TAS5747, KLM4G1FEPD, 25Q40CLSIP, H5TQ4G63CFR
Tuner: BN40-00316A DNTS403H5A
Control: Wi-Fi: WDF710Q BN59-01196C IR: BN41-02398A, Remote: BN59-01199G
Technical Specifications UE32J4500AW
SAMSUNG UE32J4500
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE32J4500 TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
In some of these cases, the main switching power supply, the Adapter module, is faulty.
This TV model is equipped with an external power adapter type Adapter 19V, which the owner can purchase independently, and repairing it may not always be advisable, however, sometimes there is a certain sense to open it and eliminate simple typical defects typical of IPS. It is necessary to measure its output supply voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for the probability of breakdown in PN semiconductor junctions.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
The breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback (OOS) stabilization circuits. PWM controllers (PWM), if they do not have visible damage to the chassis and open short circuit between the terminals, are usually checked by replacement.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V for them. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator blinks or glows constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-02360B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In some cases, to repair the MB board (SSB), it may be necessary to replace the chips - S24C256, DRV612, TAS5747, KLM4G1FEPD, 25Q40CLSIP, H5TQ4G63CFR with new or obviously working ones. In cases where BGA technologies are used, defects are usually localized by the heating method.
Malfunction of the tuner BN40-00316A DNTS403H5A is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
TV users and owners need to remember that attempts to self-repair a SAMSUNG UE32J4500 TV without the appropriate qualifications and necessary experience can lead to serious negative consequences!


The appearance of the MainBoard BN41-02360B is shown in the figure below:
BN41-02360B
BN41-02360B can be used in TVs:
SAMSUNG UE32J5200AK (Panel CY-JJ032BGLV1V), SAMSUNG UE32J5205AK UE32J5205 (Panel CY-JJ032BGLV6V), SAMSUNG UE32J4500 UE32J4500AK (Panel CY-JJ032AGHVEV).
Main features of the SAMSUNG UE32J4500 device:
Installed matrix (LED-panel) CY-JJ032AGHVEV.
The matrix control uses the Timing Controller (T-CON) ST3151A05-E-XC-2 ;.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02360B, controlled by the BD9397EFV PWM controller.
To power all internal components of the SAMSUNG UE32J4500 TV, an external adapter 19V type source is used.
MainBoard - the main board (motherboard) is a BN41-02360B module, using S24C256, DRV612, TAS5747, KLM4G1FEPD, 25Q40CLSIP, H5TQ4G63CFR and other chips.
The tuner BN40-00316A DNTS403H5A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J4710AK

Technical description and composition of the SAMSUNG UE32J4710AK TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J4710AK
Chassis / Version: CA01
Panel: CY-JJ032AGHV6V
LED backlight: LM41-00353A, LM41-00353A
LED driver (backlight): integrated into MainBoard
PWM LED driver: BD9397EFV
Power Supply (PSU): Adapter 19V
MainBoard: BN41-02360B BN94-08207B
IC MainBoard: K4B2G1646Q, TAS5747, 25Q40CLSIP, S24C256
Tuner: BN40-00316A DNTS403H5A
Control: IR: BN41-02398A REV1.3, WiFi: BN59-01196C WDF710Q
Technical Specifications UE32J4710AK
SAMSUNG UE32J4710AK
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE32J4710AK TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
Most often, with such manifestations, the main adapter power module is faulty.
This TV model is equipped with an external power adapter type Adapter 19V, which the owner can purchase independently, and repairing it may not always be advisable, however, sometimes there is a certain sense to open it and eliminate simple typical defects typical of IPS. Then we recommend that you measure its output voltages and, if they are absent, you should check the health of the power switches and rectifier diodes of the converters for a probable short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM circuits are usually checked by replacement with new ones, or known to be working.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
Failure in most such cases is detected in the nodes and backlight elements of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN-junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the BN41-02360B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Board repair and replacement of K4B2G1646Q, TAS5747, 25Q40CLSIP, S24C256 microcircuits are carried out with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
Before replacing the tuner BN40-00316A DNTS403H5A, if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Attention! Users and owners of UE32J4710AK TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.

The appearance of the MainBoard BN41-02360B is shown in the figure below:
BN41-02360B
BN41-02360B can be used in TVs:
SAMSUNG UE32J5200AK (Panel CY-JJ032BGLV1V), SAMSUNG UE32J5205AK UE32J5205 (Panel CY-JJ032BGLV6V), SAMSUNG UE32J4500 UE32J4500AK (Panel CY-JJ032AGHVEV).
Main features of the SAMSUNG UE32J4710AK device:
Installed matrix (LED-panel) CY-JJ032AGHV6V.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02360B, controlled by the BD9397EFV PWM controller.
To power all internal components of the SAMSUNG UE32J4710AK TV, an external adapter 19V type source is used.
MainBoard - the main board (motherboard) is a BN41-02360B module, using K4B2G1646Q, TAS5747, 25Q40CLSIP, S24C256 and others.
The tuner BN40-00316A DNTS403H5A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J5000AK

Technical description and composition of the SAMSUNG UE32J5000AK TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J5000AK UE32J5000
Chassis / Version: Ver - US02
Panel: CY-JJ032BGLV1V
LED backlight: 2015 SVS32 FHD F-COM 7LEDS REV1.3 150223 LM41-00134A
T-CON: BN41-02111A BN95-02146B
LED driver (backlight): with integrated PSU
Power Supply (PSU): A5919_FSM Adapter 19V 3.17A - BN44-00838A A5919_FSM
MainBoard: BN41-02358A BN94-08230A
IC MainBoard: NAND: F59L1G81A-25TI, DDR: K4B2G1646Q-BCK0, FLASH: W25Q40CLSIP, EPRROM: S24C256
Tuner: BN40-00316A DNTS403H5A
Control: IR: BN41-02398A A36076G
Appearance
SAMSUNG UE32J5000AK
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE32J5000AK does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lights do not light or flash.
In such cases, the adapter power supply is usually faulty.
The external adapter 19V 3.17A - BN44-00838A A5919_FSM power supply is not always subject to repair, especially since the owner can purchase it independently. But, in some cases, it makes sense to open it and eliminate the simple typical defects inherent in converters in pulsed sources. It is then necessary to measure its output voltages and, if they are absent, you should check the power switches and rectifier diodes of the converters for the probability of a short circuit.
In the event of breakdowns in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse or current sensor at the source of the key most often breaks.
The breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback (OOS) stabilization circuits. PWM controllers (PWM), if they do not have visible damage to the chassis and open short circuit between the terminals, are usually checked by replacement.
- There is no image, there is sound, there is a reaction to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
In some of these cases, a malfunction is caused by a lack of display backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN-junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the BN41-02358A motherboard should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, you should update or replace the software (software). When repairing an MB board, you must check its components NAND: F59L1G81A-25TI, DDR: K4B2G1646Q-BCK0, FLASH: W25Q40CLSIP, EPRROM: S24C256. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
Malfunction of the tuner BN40-00316A DNTS403H5A is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Attention TV owners! Attempts to self-repair SAMSUNG UE32J5000AK are not recommended by the manufacturer and can lead to serious negative consequences!


FIRMWARE  Main, T-con ----------> SAMSUNG UE32J5000AK UE32J5000, Main: BN41-02358A BN94-08230A, Panel: CY-JJ032BGLV1V

The appearance of the MainBoard BN41-02358A is shown in the figure below:
BN41-02358A
The appearance of the power supply
Main features of the SAMSUNG UE32J5000AK device:
Installed matrix (LED panel) CY-JJ032BGLV1V.
The matrix control uses the Timing Controller (T-CON) BN41-02111A.
To power the backlight LEDs, a converter is used, combined with a power supply.
An external source of the type A5919_FSM Adapter 19V 3.17A - BN44-00838A A5919_FSM is used to power all internal nodes of the SAMSUNG UE32J5000AK TV.
MainBoard - the main board (motherboard) is a BN41-02358A module, using NAND chips: F59L1G81A-25TI, DDR: K4B2G1646Q-BCK0, FLASH: W25Q40CLSIP, EPRROM: S24C256 and others.
The tuner BN40-00316A DNTS403H5A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J5005AK

Technical description and composition of the SAMSUNG UE32J5005AK TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J5005AK UE32J5005
Chassis / Version: LB04
Panel: JJ032BGE-R1
LED backlight: V5DN-320SM1-R2
T-CON: HV320FHB-N10
LED driver (backlight): integrated into MainBoard
Power Supply (PSU): A5919_FSM Adapter 19V 3.17A
MainBoard: BN41-02358C BN94-08230A
IC MainBoard: SPI: W25Q40CLSIP, EEPROM: S24C256C4KGI, NAND: F59L1G81A-25TI
Tuner: BN40-00316A
Technical Specifications UE32J5005AK
SAMSUNG UE32J5005AK
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE32J5005AK TV does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lights do not light or flash.
Often in such cases, the A5919_FSM power module is faulty.
The external power supply unit A5919_FSM Adapter is not always subject to repair, especially since the owner can purchase it independently. But, in some cases, it makes sense to open it and eliminate the simple typical defects inherent in converters in pulsed sources. Then it is necessary to measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches and rectifier diodes of the converters for the presence of a possible short circuit.
In case of breakdowns of diodes in the secondary circuits, the converter can operate in emergency short circuit mode without output voltages, and during short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor at the source of the key usually breaks.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible key parameters. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers, in the absence of visible damage or frank short-circuit between the terminals, are checked by replacing with new, or obviously working.
- There is no image, there is sound, it responds to the remote. Or the image may appear for a second when turned on and immediately disappears.
The most likely in these cases is a malfunction of the LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-02358C motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In some cases, to repair the MB board (SSB), it may be necessary to replace the chips - SPI: W25Q40CLSIP, EEPROM: S24C256C4KGI, NAND: F59L1G81A-25TI with new or obviously working ones. In cases where BGA technologies are used, defects are usually localized by the heating method.
If the TV works normally from external devices, but does not tune into television channels, the tuner BN40-00316A may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention to users! Self-repair of a SAMSUNG UE32J5005AK TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!


FIRMWARE FOR  SPI FLASH ----------> SAMSUNG UE32J5005AK, Main: BN41-02358B.

The appearance of the MainBoard BN41-02358C is shown in the figure below:
BN41-02358C
The appearance of the power supply
Main features of the SAMSUNG UE32J5005AK device:
Installed matrix (LED-panel) JJ032BGE-R1.
The matrix control uses the Timing Controller (T-CON) HV320FHB-N10.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02358C.
An external source of the A5919_FSM Adapter 19V 3.17A type is used to power all internal nodes of the SAMSUNG UE32J5005AK TV.
MainBoard - the main board (motherboard) is a BN41-02358C module, using SPI microcircuits: W25Q40CLSIP, EEPROM: S24C256C4KGI, NAND: F59L1G81A-25TI and others.
The tuner BN40-00316A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J5100AK

Technical description and composition of the SAMSUNG UE32J5100AK TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J5100AK UE32J5100
Panel: CY-GH032BGSV1V
T-CON: RUNTK 5351TP 0055FV (52K04)
LED driver (backlight): integrated into MainBoard
PWM LED driver: 7014X
Power Supply (PSU): BN44-00697A REV1.4 L32SF_ESM PSLF720S06A
PWM Power: S3330 (FAN6755)
MOSFET Power: 60R580P
MainBoard: BN41-02098B BN94-08117P
IC MainBoard: F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414
Tuner: DNTS243EH286A BN40-00294A
Technical Specifications UE32J5100AK
SAMSUNG UE32J5100AK
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE32J5100AK does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
Often in such cases, the BN44-00697A power module is faulty. It is necessary to measure the output voltages in its secondary circuits, and if they are completely absent, check the serviceability of the power switches and rectifier diodes for a possible breakdown (short circuit).
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM circuits are usually checked by replacement with new ones, or known to be working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V for them. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its chips F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
If the TV works normally from external devices, but does not tune into television channels, the tuner DNTS243EH286A BN40-00294A may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention to users! Self-repair of a SAMSUNG UE32J5100AK TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!

The appearance of the MainBoard BN41-02098B is shown in the figure below:
BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel CY-JJ040BGNV2V), SAMSUNG UE40H5020 UE40H5020AK (Panel CY-GH040BGSV1V), SAMSUNG UE40J5100AU (Panel CY-GH040BGSR1V), SAMSUNG T31D310EW (Panel CY-HH032AGSV1H), SAMSUNG UE48J5000AU (Panel CY-JJ048BGEV5V), SAMSUNG UE32H5020AK (Panel CY-GH032BGLV4V), SAMSUNG UE40J5120AU (Panel CY-GH040BGSV1V), SAMSUNG LT32E310EX T32E310EX (Panel CY-GJ032BGEV1V), SAMSUNG UE40H5270 UE40H5270AU (Panel CY-GH048BGLV1V), SAMSUNG UE32J5100AK UE32J5100 (Panel CY- GH032BGSV1V), SAMSUNG UE32H5000AK UE32H5000 (Panel CY-GH032BGLV1V), SAMSUNG UE48H5000 UE48H5000AK (Panel CY-GH048CSLV1V), SAMSUNG UE32J5120AK UE32JSV1B (CY.
The appearance of the power supply
Main features of the SAMSUNG UE32J5100AK device:
Installed matrix (LED panel) CY-GH032BGSV1V.
The matrix control uses the Timing Controller (T-CON) RUNTK.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02098B, controlled by the 7014X PWM controller.
The necessary supply voltages for all nodes of the SAMSUNG UE32J5100AK TV are generated by the BN44-00697A power module or its analogs using S3330 microcircuits (FAN6755) and power switches of the 60R580P type.
MainBoard - the main board (motherboard) is a BN41-02098B module, using chips F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 and others.
The tuner DNTS243EH286A BN40-00294A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J5120AK

Technical description and composition of the SAMSUNG UE32J5120AK TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J5120AK UE32J5120
Chassis / Version: MS02
Panel: CY-GH032BGSV1V
LED backlight: LM41-00099L
T-CON: RUNTK 5351TP ZA 0055FV + K5439TP 5440TP
LED driver (backlight): integrated into PSU
PWM LED driver: 7014X
Power Supply (PSU): BN44-00697A L32SF_ESM PSLF720S06A
PWM Power: S3330 = FAN6755W
MOSFET Power: 60R580P
MainBoard: BN41-02098B BN94-08117X
IC MainBoard: F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414
Tuner: BN40-00294A
Technical Specifications UE32J5120AK
SAMSUNG UE32J5120AK
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The SAMSUNG UE32J5120AK TV does not turn on and does not show any signs of operability at all. There is no reaction to the remote control and control buttons from the front panel.
Most often, with such manifestations, the main power module BN44-00697A is found to be faulty. In the absence of the necessary supply voltages in the secondary circuits of the converters, it is necessary to check the power switches (60R580P) and rectifier diodes for a possible partial or complete breakdown.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) S3330 = FAN6755W, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the health of its elements - F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 which may require replacement with new ones. If the BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
The malfunction of the tuner BN40-00294A is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair to professionals with sufficient experience in the repair of electronic equipment.

The appearance of the MainBoard BN41-02098B is shown in the figure below:
BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel CY-JJ040BGNV2V), SAMSUNG UE40H5020 UE40H5020AK (Panel CY-GH040BGSV1V), SAMSUNG UE40J5100AU (Panel CY-GH040BGSR1V), SAMSUNG T31D310EW (Panel CY-HH032AGSV1H), SAMSUNG UE48J5000AU (Panel CY-JJ048BGEV5V), SAMSUNG UE32H5020AK (Panel CY-GH032BGLV4V), SAMSUNG UE40J5120AU (Panel CY-GH040BGSV1V), SAMSUNG LT32E310EX T32E310EX (Panel CY-GJ032BGEV1V), SAMSUNG UE40H5270 UE40H5270AU (Panel CY-GH048BGLV1V), SAMSUNG UE32J5100AK UE32J5100 (Panel CY- GH032BGSV1V), SAMSUNG UE32H5000AK UE32H5000 (Panel CY-GH032BGLV1V), SAMSUNG UE48H5000 UE48H5000AK (Panel CY-GH048CSLV1V), SAMSUNG UE32J5120AK UE32JSV1B (CY.
The appearance of the power supply
Main features of the SAMSUNG UE32J5120AK device:
Installed matrix (LED panel) CY-GH032BGSV1V.
The matrix control uses the Timing Controller (T-CON) RUNTK.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a 7014X PWM controller.
The necessary supply voltages for all nodes of the SAMSUNG UE32J5120AK TV are generated by the BN44-00697A power module or its analogs using S3330 = FAN6755W microcircuits and 60R580P type power switches.
MainBoard - the main board (motherboard) is a BN41-02098B module, using chips F59L1G81A, 25Q40CLSIP, S24C256, K4B2G1646Q-BCKO, NTP7414 and others.
The tuner BN40-00294A provides the reception of television programs and tuning to channels

REPAIR / SERVICING TV SAMSUNG UE32J5200AK

Technical description and composition of the SAMSUNG UE32J5200AK TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J5200AK
Chassis / Version: Ver: TS01
Panel: CY-JJ032BGLV1V
LED backlight: V5DN-320SM1-R2 (15.05.13)
T-CON: BN41-02111A
LED driver (backlight): with integrated MainBoard
PWM LED driver: BD9397EFV
Power Supply (PSU): Adapter
MainBoard: BN41-02360B BN94-08318B
IC MainBoard: K4B2G1646Q, TAS5747
Tuner: BN40-00316A
Control: IR: BN41-02398A, Wi-Fi: WDF710Q BN59-01196C
Technical Specifications UE32J5200AK
SAMSUNG UE32J5200AK
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE32J5200AK does not turn on. There are no signs of operability. The indicators on the front panel do not shine and do not blink, and the remote control and control buttons do not respond.
In the vast majority of such cases, a malfunction is detected in the Adapter power module.
This TV model is equipped with an external adapter type power supply, which the owner can purchase on his own, and repairing it may not always be advisable, however, sometimes it makes sense to open it and eliminate simple typical defects typical of IPS. It is necessary to measure the secondary output voltage, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, power supply, frequency-setting, damper ... as well as elements of the Negative Stabilization Feedback. The PWM chip can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no image, there is sound, it responds to the remote. Or the image may appear for a second when turned on and immediately disappears.
Failure in most such cases is detected in the nodes and backlight elements of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Usually, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-02360B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the elements K4B2G1646Q, TAS5747. BGA chip malfunctions are usually easy to detect by warming up.
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the tuner BN40-00316A. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
Owners and users of the SAMSUNG UE32J5200AK TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!


The appearance of the MainBoard BN41-02360B is shown in the figure below:
BN41-02360B
BN41-02360B can be used in TVs:
SAMSUNG UE32J5200AK (Panel CY-JJ032BGLV1V), SAMSUNG UE32J5205AK UE32J5205 (Panel CY-JJ032BGLV6V), SAMSUNG UE32J4500 UE32J4500AK (Panel CY-JJ032AGHVEV).
Main features of the SAMSUNG UE32J5200AK device:
Installed matrix (LED panel) CY-JJ032BGLV1V.
The matrix control uses the Timing Controller (T-CON) BN41-02111A.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02360B, controlled by the BD9397EFV PWM controller.
To power all internal components of the SAMSUNG UE32J5200AK TV, an external adapter type source is used.
MainBoard - the main board (motherboard) is a BN41-02360B module, using K4B2G1646Q, TAS5747 and others.
The tuner BN40-00316A provides the reception of television programs and tuning to channels.

REPAIR / SERVICING TV SAMSUNG UE32J5205AK

Technical description and composition of the SAMSUNG UE32J5205AK TV, panel type and applicable modules. The composition of the modules.
SAMSUNG LED
Model: UE32J5205AK UE32J5205
Panel: CY-JJ032BGLV6V // JJ032BGE-R3
LED backlight: V5DN-320SM1-R2
T-CON: N41-02292A BN95-03524B
LED driver (backlight): integrated into MainBoard
Power Supply (PSU): A6619_FSM BN44-00837A Adapter 19.5V 3.474A
MainBoard: BN41-02360B BN94-08318B
IC MainBoard: K4B2G1646Q, TAS5747
Tuner: BN40-00316A
Control: WDF710Q BN59-01196C
Technical Specifications UE32J5205AK
SAMSUNG UE32J5205AK
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE32J5205AK does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
In such cases, the A6619_FSM power supply is usually faulty.
The owner of a TV can purchase an external power supply unit such as A6619_FSM and repairing it is not always advisable. In any case, the simplest typical defects characteristic of most IIP schemes can be easily detected and eliminated after opening. In the absence of the necessary supply voltages in the secondary circuits of the converters, it is necessary to check the power switches and rectifier diodes for a possible partial or complete breakdown.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM circuits are usually checked by replacement with new ones, or known to be working.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
Often in such cases, there is no LED backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator blinks or glows constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-02360B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its K4B2G1646Q, TAS5747 chips and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Before changing the tuner BN40-00316A, if it is not possible to tune to television channels, you should make sure that there are supply voltages that must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
We recommend the owners of the UE32J5205AK TV for repair only to qualified specialists with the necessary work experience! Attempts to repair it yourself without the appropriate knowledge and skills can lead to irreversible negative consequences!

Variant UE32J5205 version XA08 - Panel: JJ032BGE-R3, T-Con: HV320FHB-N10 HV480FH2-600, MainBoard: BN41-02360B BN94-08318N.

The appearance of the MainBoard BN41-02360B is shown in the figure below:
BN41-02360B
BN41-02360B can be used in TVs:
SAMSUNG UE32J5200AK (Panel CY-JJ032BGLV1V), SAMSUNG UE32J5205AK UE32J5205 (Panel CY-JJ032BGLV6V), SAMSUNG UE32J4500 UE32J4500AK (Panel CY-JJ032AGHVEV).
The appearance of the power supply
Main features of the SAMSUNG UE32J5205AK device:
Installed matrix (LED-panel) CY-JJ032BGLV6V or JJ032BGE-R3.
The matrix control uses the Timing Controller (T-CON) N41-02292A.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02360B.
An external source of the type A6619_FSM BN44-00837A Adapter 19.5V 3.474A is used to power all internal nodes of the SAMSUNG UE32J5205AK TV.
MainBoard - the main board (motherboard) is a BN41-02360B module, using K4B2G1646Q, TAS5747 and others.
The tuner BN40-00316A provides the reception of television programs and tuning to channels.