REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Thursday 21 March 2019

DISH NETWORK -EZ REMOTE CONTROL - SETUP PROCEDURE

DISH NETWORK -EZ REMOTE CONTROL - SETUP PROCEDURE




CONNECTING THE SATELLITE RECEIVER & TV
  • Connect a coaxial cable between the TV Set Out on the satellite receiver and the tuner input on the TV
Note: If you connect your TV a different way (for example, using yellow, red, and white audio/video RCA-type or S-Video cables), the feature to switch your TV to satellite programming using will not work.
Set [ 4 – 3 ] channel on the back of the receiver toCH3.  [Note: If you prefer Channel 4, instructions are provided later to change this setting.   If your satellite receiver does not have a [ 4 – 3 ] channel, see your satellite receiver’s User’s Guide for how to set TV Set Out on the satellite receiver to Channel 3.

SETTING UP THE REMOTE TO CONTROL YOUR TV
1. Find the brand name of your TV in the TV code tables. [refer previous post here] 2. Turn on your TV.
3. Press and hold [Antenna button] until both [sat & tv button] lights turn on (it takes about five seconds).
4. Release . [Antenna & TV] light will flash.
5. Press [TV]. Notice [TV] light turns on and stays on.
6. Enter one of the three-digit codes for your TV from the TV code tables while [TV] light is on.  [Note: You have about 20 seconds to begin entering the TV code.]
7. Press the MUTE button and watch [TV] light.  If [TV] light flashes three times, the code is valid and you can go to step 8. If [TV] light does not flash at all, the code may not have been entered correctly. So, start over from step 3 and try the code again.
8. Press [TV] and your TV should shut off. If your TV shuts off, go to step 9. If not, pick another code for your TV brand from the TV Codes table and go back to step 3. If you have tried all of the codes and none work, go to How to Scan for TV and VCR.
9. Turn your TV back on by pressing [TV] again and try the other buttons below to make sure they work. ( Press the 0 through 9 buttons to change channels on your TV.)
Press [Ch Up] and Ch Dn] to change channels on your TV.
Press to change the TV volume.  If [Vol+/Vol -] buttons work, go on to the next section to set up . If not, pick another code for your TV brand from the TV Codes table
step 3.
1. Make sure your TV and satellite receiver are connected and your remote control is set up to control your TV using the instructions in the last two sections.
2. Turn on your TV and tune to a channel other than 3 (for example, 4 or 5).
3. Press and your satellite receiver should turn on and your TV should tune to Channel 3.
4. Press theMENUbutton. If you see the satellite receiver Menu screen, gotostep5. If not, go to step 15.
5. If you want to keep your satellite programming on TV Channel 3, check the box below and go to step 28.
6. If you prefer to have your satellite programming on TV Channel 4,go onto step7. VOL
7. Set the switch on the back of the satellite receiver toCH4. The TV will lose the picture from the satellite receiver, but this is OK.
Note: If your satellite receiver does not have a switch, see your satellite receiver’s User’s Guide for how to set TV Set Out on the satellite receiver to channel 4.
8. Press and hold until both lights turn on (it takes about five seconds).
9. Release . light will flash.
10.Enter0-4.
11. Press MUTE while watching light.
12. light will flash three times.  If the light does not flash at all, repeat this procedure starting with step 8.
13.Press while watching your TV. If your TV tunes to Channel 4, go to step 14. If not, go to step 7.
14.Press the MENU button. If you see the satellite receiver Menu screen, check the box below and go to step 28.

 TO CONTROL YOUR TV
1. Find the brand name of your TV in the TV code tables. [refer previous post here] 2. Turn on your TV.
3. Press and hold [Antenna button] until both [sat & tv button] lights turn on (it takes about five seconds).
4. Release . [Antenna & TV] light will flash.
5. Press [TV]. Notice [TV] light turns on and stays on.
6. Enter one of the three-digit codes for your TV from the TV code tables while [TV] light is on.  [Note: You have about 20 seconds to begin entering the TV code.]
7. Press the MUTE button and watch [TV] light.  If [TV] light flashes three times, the code is valid and you can go to step 8. If [TV] light does not flash at all, the code may not have been entered correctly. So, start over from step 3 and try the code again.
8. Press [TV] and your TV should shut off. If your TV shuts off, go to step 9. If not, pick another code for your TV brand from the TV Codes table and go back to step 3. If you have tried all of the codes and none work, go to How to Scan for TV and VCR.
9. Turn your TV back on by pressing [TV] again and try the other buttons below to make sure they work. ( Press the 0 through 9 buttons to change channels on your TV.)
Press [Ch Up] and Ch Dn] to change channels on your TV.
Press to change the TV volume.  If [Vol+/Vol -] buttons work, go on to the next section to set up . If not, pick another code for your TV brand from the TV Codes table
step 3.
1. Make sure your TV and satellite receiver are connected and your remote control is set up to control your TV using the instructions in the last two sections.
2. Turn on your TV and tune to a channel other than 3 (for example, 4 or 5).
3. Press and your satellite receiver should turn on and your TV should tune to Channel 3.
4. Press theMENUbutton. If you see the satellite receiver Menu screen, gotostep5. If not, go to step 15.
5. If you want to keep your satellite programming on TV Channel 3, check the box below and go to step 28.
6. If you prefer to have your satellite programming on TV Channel 4,go onto step7. VOL
7. Set the switch on the back of the satellite receiver toCH4. The TV will lose the picture from the satellite receiver, but this is OK.
Note: If your satellite receiver does not have a switch, see your satellite receiver’s User’s Guide for how to set TV Set Out on the satellite receiver to channel 4.
8. Press and hold until both lights turn on (it takes about five seconds).
9. Release . light will flash.
10.Enter0-4.
11. Press MUTE while watching light.
12. light will flash three times.  If the light does not flash at all, repeat this procedure starting with step 8.
13.Press while watching your TV. If your TV tunes to Channel 4, go to step 14. If not, go to step 7.
14.Press the MENU button. If you see the satellite receiver Menu screen, check the box below and go to step 28.
Posted By: FRANK at 04:45
TAG: ,