PANASONIC FULLY AUTOMATIC WASHING MACHINE - Panasonic NA-F65B2 - NA-F70B2 - NA-F72B2 - NA-F852B - NA-F902B – error codes – troubleshooting – Wiring diagram - washing machine repair and service
Category: Washing Machine Repair and Service
Contents of this article
- Error codes cause and solution
- Troubleshooting
Panasonic NA-F65B2 - NA-F70B2 - NA-F72B2 - NA-F852B - NA-F902B
Error indication
Error U11
Check if abnormalities listed below are seen
in the external water hose.
Is the hose connected?
Is it clogged with lint?
Is it crushed?
Is the tip soaked in water?
Is a part of hose at a height of over 10 cm midway?
Is the extension hose longer than 3 m?
Is the hose being used too small?
Is the hose connected?
Is it clogged with lint?
Is it crushed?
Is the tip soaked in water?
Is a part of hose at a height of over 10 cm midway?
Is the extension hose longer than 3 m?
Is the hose being used too small?
Restart with opening and closing the lid.
Error U12
Check if the lid is opened.
Close the lid.
Close the lid.
Error U13
Is the washing machine is an unsteady
position, or is it on an inclined floor surface?
Is the laundry unevenly distributed in the tub?
Arrange the laundry evenly in the tub, then close the lid.
Is the laundry unevenly distributed in the tub?
Arrange the laundry evenly in the tub, then close the lid.
Error U14
Check if you have forgotten to connect the
water hose and to turn on the faucet.
Is the water supply cut off?
Is the water supply cut off?
Error U99
Check if lid is open when draining operation
of the [CHILD LOCK] program is ON.
Error H01
In case of H displays such as “H01”, with no
buzzer sounds pull out the power plug, and contact your dealer for service.
TROUBLESHOOTING
The water is drained even filled by a bucket
When the laundry amount is large at the HIGH
water level, the machine sometimes fills automatically. When level goes down,
the machine fills automatically.
The water level is too high for the amount of laundry being washed.
When the laundry is already soaked with water
before the wash is started, or if there is water in the tub before the wash is
started, the water level will sometimes be higher.
The water level is too low for the amount of laundry being washed.
With light laundry made of synthetic or blended
fabric, the water level will sometimes be lower.
Midway during spinning, the operation suddenly changes to rinsing.
When the laundry is unbalanced during spin,
rinsing and automatic correction of unbalanced laundry will begin. Later
spinning will return to normal condition.
Water does not flow through the lint filter. Double Cascade does not
operate.
When the water level is set to very low,
water sometimes will not flow through the lint filter. Double Cascade does not
operate when these setting have been selected.
The water is drained even filled by a bucket
Do not leave more than 15 seconds while
powered on. Fill the water while powered off or after pushing the start button.
During draining, the laundry and the spinner rotates with
irregular movements.
To suppress soap suds build-up, the washing
tub turns slowly and quickly.
The buttons do not work.
Only the [WATER LEVEL] button is available
after the machine begins washing.
To change the setting, press the [START/HOLD] button or press the [POWER OFF/ON] button and reconfigure the setting.
To change the setting, press the [START/HOLD] button or press the [POWER OFF/ON] button and reconfigure the setting.
If you start with the rinse cycle, the tub is not filled with
water.
When there is water in the tub, the operation
starts with the draining. After spin cycle is fi nished, the tub will be filled
with water.
Washing machine does not run at all.
Check if there is power failure.
Check if the power fuse has blown out or the breaker is actuated.
Check if the power plug is plugged in thoroughly.
Check if the “power switch” has been pressed.
Has the water faucet been turned on?
Check if the [START/HOLD] button has been pressed.
Has the machine been programmed under [RESERVE] timer?
Check if the power fuse has blown out or the breaker is actuated.
Check if the power plug is plugged in thoroughly.
Check if the “power switch” has been pressed.
Has the water faucet been turned on?
Check if the [START/HOLD] button has been pressed.
Has the machine been programmed under [RESERVE] timer?
Machine begins filling water in the middle of the wash.
When the laundry amount is large at the HIGH
water level, the machine sometimes fills automatically. When level goes down,
the machine fills automatically.
Water is not supplied.
Check if the water faucet is turned on.
Is the water supply cut off?
Check if the connection of the water supply hose is clogged with dirt.
Check if the lid is opened. Close the lid.
Is the water supply cut off?
Check if the connection of the water supply hose is clogged with dirt.
Check if the lid is opened. Close the lid.
Washing operation still continue even though the expected
finishing time had passed on Reserve Program.
Washing time will be longer because of
laundry unbalance, water feeding and draining condition.
Tub shaking with the sound of water.
This is the sound of the liquid to maintain
the balance during spinning.
Water supply failure.
Normally after the water supply failure, the
water will become muddy. Detach the water feeding hose and turn on the water
faucet to release to due muddy water. Fix water hose and start washing.
Power failure
In this case, [Power On] and [Start-Pause}
buttons need to be pressed again after electricity is restored.Then then the
machine will resume operation automatically from beginning of the stopeped process
WIRING DIAGRAM
CLICK ON THE IMAGE TO ZOOM IN
