NATIONAL PANASONIC RQ 92 KARAOKE SYSTEM, BEHRINGER B1 AND CCE CD200 CIRCUIT SCHEMATIC DIAGRAM

 National Panasonic RQ 92 schematic

Used ICs: AN6558F, AN6552, MN3007, BA3702, TA7240AP

CCE CD200 schematic

Behringer B1 condenser Microphone schematic

BEHRINGER EPX 3000 - AMPLIFIER CIRCUIT DIAGRAM

BEHRINGER EPX 3000 - AMPLIFIER CIRCUIT DIAGRAM

BEHRINGER AMPLIFIER EPX-3000  SCHEMATIC 

INPUT SECTION SCHEMATIC

AMPLIFIER SECTIONS SCHEMATICS

POWER SUPPLY [SMPS] SCHEMATIC

CLICK ON THE SCHEMATICS TO MAGNIFY

BEHRINGER B2031 SCHEMATIC - ACTIVE 2 WAY REFERENCE STUDIO MONITOR SPEAKERS

Behringer B2031 Schematic - Active 2 way reference studio monitor speakers

  As is always the case with a two-way active monitor, each B2031 is equipped with two separate power amplifiers – one for the low frequency driver and one for the tweeter (150 watts and 75 watts respectively).  The low frequency polycarbonate driver is 22cm in diameter and the high frequency duties are handled by a one-inch ferofluid-cooled titanium dome tweeter. The crossover circuitry consists of an active fourth-order Linkwitz-Riley filter kicking in at 2kHz. The enclosure also employs a bass reflex porting system to extend the low frequency drivers’ overall frequency response down to a quoted 50Hz.  Other features of the B2031s worthy of note include: protection circuitry to look after the drivers and amplifiers in the event of overload; and electromagnetic shielding to allow close placement of the B2031’s to TV screens and computer monitors without interference.

At the back of the B2031s you’ll find a metal amplifier housing which extends about an inch or so beyond the dimensions of the speaker enclosure itself (H:W:D 400 x 250 x 290mm). The balanced XLR, balanced/unbalanced TRS and 240 volt IEC power cord all connect vertically upwards into the amplifier housing, leaving the back of the B2031s free of plugs jutting out at right angles. This arrangement makes it much easier to place these monitors close to rear walls – not the best placement, admittedly, but sometimes necessary.  The rear panel of the B2031 is also where you’ll find a number of active controls. These include: Input Trim – which adjusts the B2031’s input sensitivity to the signal source; Low Frequency cut – for adapting the B2031s to an additional subwoofer system; Room Compensation – which rolls off bottom-end relative to wall/corner placement (0, - 2, -4, -6dB); and High Frequency – which compensates for the amount of high frequency damping in the monitor environment (0, +2, -2, -4dB). High and low driver mute switches are also included, which the manual suggests are for maintenance and servicing only – although  found them quite useful while setting up, as they allowed  to get a feel for the individual speaker components.  First impressions of the B2031’s were clearly centered on their extended bottom-end and the impressive definition and detail in their stereo imaging. After much listening, and a bit of tweaking of the rear-panel settings, the B2031s did a creditable job of matching themselves to my particular monitoring environment – particularly in their ability to modify the bottom end in order to compensate for their less-than-ideal close-proximity to walls and corners.

Schematic (Circuit diagram)

A first mix on the B2031s – played back on a number of passive monitors I usually use – revealed a few home truths about the differences in working with passive and active monitor designs. Although the essential balance of the mix held up impressively when played back on the passives, overall it sounded a bit lifeless. All that wonderful detail and definition that oozes out of the B2031s gets lost among the inherent limitations of your typical near field passive monitors. In essence, you still need to ‘work the mix’ on the B2031s – sweetening it up, adding punch and color as the music requires – so as to get the mix to translate effectively into the all-pervasive passive world.  From the first time I heard active reference monitors I was a convert – particularly since I had the advantage of comparing a set of active monitors right alongside a passive version from the same manufacturer. The passive pair contained identical speaker components to the active monitors and were being powered by an amplifier of quite reputable design. The difference was such that it didn’t take an audiophile to pick which monitors had more detail and definition.

The Behringer TRUTH B2031s follow in this grand tradition of the active monitor. They certainly grabbed my attention from first listen and continued to impress after countless listening sessions and mixes. At their current price-point the B2031s will certainly keep the competition honest – as well as leaving many similarly priced passive speaker/external amplifier combinations sounding somewhat lifeless.

EUROLIVE B112D-BEHRINGER Germany - PA Speaker System circuit diagram and exploded view

Active 2-Way 12" PA Speaker System with Wireless Option and Integrated Mixer

*High-Power 1000-Watt 2-way PA sound reinforcement speaker system for live and playback applications*- Ultra-compact and lightweight system delivers excellent sound even at extreme sound pressure levels

* "Wireless-ready" for high-quality BEHRINGER digital wireless system (not included)
* 2-channel mixer with individual Mic/Line inputs, Volume controls and Clip LEDs
* Dedicated 2-band EQ plus integrated sound processor for ultimate system control and speaker protection
* Revolutionary Class-D amplifier technology: enormous power, incredible sonic performance and super-light weight
* Extremely powerful 12'' long-excursion driver provides incredibly deep bass and acoustic power
* State-of-the-art 1.35'' aluminum-diaphragm compression driver for exceptional high-frequency reproduction
* Ultra-wide dispersion, large-format exponential horn
* Additional Line output allows linking of additional speaker systems
* Versatile trapezoidal enclosure design allows different positioning:
* Stand mounting with 35-mm pole socket
* Tilts on its side for use as a floor monitor
* Ergonomically shaped handles for easy carrying and setup
* High-quality components and exceptionally rugged construction ensure long life.

Input section schematic

B115MP3_INPUT EUROLIVE B112D-BEHRINGER Germany

SMPS schematic - B112D-BEHRINGER Germany

POAJN 01-INPUT - EUROLIVE B112D-BEHRINGER Germany

EUROLIVE B112D-BEHRINGER Germany Amplifier schematic

Exploded views