Master Electronics Repair !

Welcome to Master Electronics Repair! website.Here you will find:Service Modes, Circuit Diagrams,Service manuals, Firmware Update procedure, Disassemble procedure, Universal remote control setup codes, Troubleshooting, Diagnosing, Measuring, and more.... of many of LCD/LED TV/Displays,others various electronic apparates,trough many technical notes and tips/tricks to help repairing/fixing Troubles/ faults,for electrical technicians.This site helps you to save the Earth from electronic waste!

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!

Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:

- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Monday, 4 March 2019

APPLE IPHONE 5 – HOW TO REPLACE THE BATTERY OF APPLE IPHONE 5 – MOBILES AND SMART PHONES REPAIR AND SERVICE

Apple iPhone 5 – how to replace the battery of apple iPhone 5 – mobiles and smart phones repair and service

Category: Mobiles and Smartphones Repair and Service

Contents of this article

How to repave the battery
How to remove the case

Apple iPhone 5

Display Assembly procedure

If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered.
This will keep glass shards contained and provide structural integrity when prying and lifting the display.
wear safety glasses to protect your eyes from any glass shaken free during the repair

Before disassembling your iPhone, be sure it is powered off.

Remove the two 3.6 mm Pentalobe screws next to the Lightning connector.

The next two steps demonstrate using the iSclack, a great tool for safely opening the iPhone 5 that we recommend for anyone doing more than one repair.

Close the handle on the iSclack, opening the suction-cup jaws. Place the bottom of your iPhone in between the suction cups, against the plastic depth gauge.
The top suction cup should rest just above the home button. Open the handles to close the jaws of the iSclack. Center the suction cups and press them firmly onto the top and bottom of the iPhone.

Hold onto your iPhone securely and close the handle of the iSclack to separate the suction cups, pulling the front panel up from the rear case.

The iSclack is designed to safely open your iPhone just enough to separate the pieces, but not enough to damage the home button cable.
Peel the two suction cups off your iPhone.

Press a suction cup onto the screen, just above the home button.

Be sure the cup is completely on the screen to get a tight seal.
If you're opening an iPhone with cracked glass, neatly lay a couple strips of packing tape across the front and squeeze out as many bubbles as you can. This will give the suction cup a surface to grab, and minimize the spread of broken glass.

Make sure the suction cup is firmly attached to the front panel assembly.

While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel assembly from the rear case.
Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices.
With a plastic opening tool, begin to gently pry the rear case down, away from the display assembly, while you pull up with the suction cup.
There are several clips attaching the front panel assembly to the rear case, so you may need to use a combination of the suction cup and plastic opening tool to free the front panel assembly.

Continue to pry up around the sides of the front panel assembly, detaching the clips along the left and right side.

Do not try to completely remove the front panel assembly from the rear case, as there are several ribbon cables still attached at the top of the iPhone.

Be sure to disconnect the battery first before proceeding with the repair as not doing so can sometimes cause the phone to run hot and/or have issues with touch sensitivity.
Once the clips have been released on the bottom and sides of the front panel assembly, pull the bottom of the assembly away from the rear case.
Lift the front panel assembly slowly up to about 90 degrees from the rear case.

Remove the following screws securing the front panel assembly cable bracket to the logic board:

Two 1.2 mm Phillips screws

One 1.6 mm Phillips screw
This screw tends to not be attracted to a magnetized screwdriver. Take care not to lose it when removing, and make sure it gets back into the right place—a magnetized screw may interfere with the compass.
Remove the front panel assembly cable bracket from the logic board. User note: To ensure correct installation, make sure you clip the small hooks of the bracket under and then lower towards the outside of the phone.

Use a plastic opening tool to disconnect the three front panel assembly cables: Front-facing camera and sensor cable

LCD cable
Digitizer cable
When reassembling your phone, The LCD cable may pop off the connector. This can cause white lines, or nothing at all to appear when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery.

Remove the front panel assembly from the rear case.

Remove the following two screws securing the metal battery connector bracket to the logic board:

One 1.8 mm Phillips screw
One 1.6 mm Phillips screw

Remove the metal battery connector bracket from the iPhone.

Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.

Be very careful to only pry up on the battery connector and not the socket on the logic board. If you pry up on the logic board socket, you may break the connector entirely.

It may be possible to remove the battery simply by pulling on the plastic pull-tab. A slow continual pull seems to work best. If this is insufficient, proceed with the prying outlined in this step.

Use the plastic opening tool to gently pry the battery up, only at the three points shown. Prying anywhere else, especially near the clear plastic pull tab, may result in damage to the logic board.
Again, do not pry too hard, and only in the locations shown; well above and below the clear plastic pull tab. Otherwise, you may deform or puncture the battery or damage the logic board.
Be careful when prying at the top of the battery. Do not insert the opening tool more than 2 mm under the battery or you risk severing the volume control cables.

If necessary, use the exposed clear plastic pull tab to peel the battery off the adhesive securing it to the iPhone.

Remove the battery.
During reassembly, make sure the battery is seated firmly against the rear case. This will prevent any damage to other components when reinstalling the front panel assembly.