Master Electronics Repair !

Welcome to Master Electronics Repair! website.Here you will find:Service Modes, Circuit Diagrams,Service manuals, Firmware Update procedure, Disassemble procedure, Universal remote control setup codes, Troubleshooting, Diagnosing, Measuring, and more.... of many of LCD/LED TV/Displays,others various electronic apparates,trough many technical notes and tips/tricks to help repairing/fixing Troubles/ faults,for electrical technicians.This site helps you to save the Earth from electronic waste!

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!

Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:

- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Wednesday, 6 March 2019

BENQ W1070 - W1080ST DIGITAL PROJECTOR LAMP REPLACING – LAMP HOUR RESET - LAMP SETTINGS – PROJECTOR REPAIR AND SERVICE

BENQ W1070 - W1080ST Digital Projector lamp replacing – Lamp hour reset - Lamp settings – Projector Repair and service

Category: Projector Repair and Service

Contents of this article

Lamp settings
Lamp replacement
Lamp hour reset

BENQ W1070 - W1080ST

Auto Off Setting
This function allows the projector to turn off automatically if no input source is detected after a set period of time.
To set Auto Off, go to the System Setup : Basic > Auto Off menu and press LEFT/RIGHT to select a time period. The time period can be set from 5 to 30 minutes in 5-minute increments. If the preset time lengths are not suitable for your presentation, select Disable. The projector will not automatically shut down in a certain time period.

When to replace the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact for service The following Lamp warning displays will remind you to change the lamp.

Install a new lamp for optimal performance. If the projector is normally run with Economic selected, you may continue to operate the projector until the next hour lamp warning appears. Press MODE/ENTER to dismiss the message. It is recommended that to replace the lamp at this stage. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. Press MODE/ENTER to dismiss the message.

The lamp MUST be replaced before the projector will operate normally. Press MODE/ENTER to dismiss the message

How to replace the lamp

Procedure # To reduce the risk of electrical shock, always turn the projector off and disconnect the power cable before changing the lamp.
# To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
# To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.
# To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.
# This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.

1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Loosen the screw that secures the lamp cover on the side of the projector until the lamp cover loosens.

3. Remove the lamp cover from the projector.
# Do not turn the power on with the lamp cover removed.
# Do not insert your fingers between the lamp and the projector.
The sharp edges inside the projector may cause injuries.

4. Loosen the screw that secures the lamp.
5. Lift the handle so that it stands up.

6. Use the handle to slowly pull the lamp out of the projector.
# Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.
# Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.
# Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

7. As shown in the figure, lower the new lamp.

8. Tighten the screw that secures the lamp.
9. Ensure the handle is fully laid flat and locked in place.
# Loose screw may cause a bad connection, which could result in malfunction.
# Do not over tighten the screw.

10. Replace the lamp cover on the projector.

11. Tighten the screw that secures the lamp cover.
# Loose screw may cause a bad connection, which could result in malfunction.
# Do not over tighten the screw.

12. Connect the power and restart the projector.

HOW TO RESET THE LAMP HOUR OF BENQ PROJECTOR
Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.
1. After the start-up logo, press MENU/EXIT and then press LEFT/RIGHT until the System Setup :Advanced menu is highlighted.
2. Press DOWN to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page displays. 3. Highlight Reset Lamp Timer and press MODE/ENTER. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to "0".