REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Wednesday, 13 March 2019

FUNAI LED40-H9200M SERVICE MODE AND POWER SUPPLY ADJUSTMENT

FUNAI LED40-H9200M SERVICE MODE AND POWER SUPPLY ADJUSTMENT 

LED LCD TV SERVICE MODE AND POWER SUPPLY ADJUSTMENT 


SERVICE MODE
1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Software” in “OTHERS” and press [OK] button.
4. Press [0], [4], [2], [5], [7], [4] and [ ] buttons on the remote control unit in this order. The following screen appears.
Purity Check Mode
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.
White Balance Adjustment
Purpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
3. Enter the Service mode.
4. Press [ VOLUME -- ] button three times on the remote control unit to select “Drive setting” mode. “Drive” appears on the screen.
5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears on the screen.)
6. Press [MENU] button. The internal Raster signal appears on the screen. (“Internal (Single)” appears on the upper right of the screen as shown below.)
7. Press [P UP /DOWN ] buttons to adjust the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.002).
8. Press [1] button to select the “HDR” for High Drive Red adjustment (“HDR” appears on the screen.) and press [P UP/DOWN ] buttons to adjust the color temperature.
9. If necessary, adjust the “HDB” or “HDR” again.
10. Press [6] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears on the screen.) and press [P UP/DOWN ] buttons to adjust the color temperature.
11. Press [4] button to select the “LDR” for Low Drive Red adjustment (“LDR” appears on the screen.) and press [P UP/DOWN ] buttons to adjust the color temperature.
12. If necessary, adjust the “LDB” or “LDR” again.
13. Press [BACK] button to enter the Service mode again.
14. Press [INFORMATION i ] button on the remote control unit to shift to the self check mode screen. If “WB OK” is displayed, this adjustment completes. If “WB NG” is displayed, turn the AC switch (on the lower left of the back of the unit) off and on. Then repeat above steps from 3. to 13. Check the self check mode screen again. If “WB NG” is displayed, replace the LCD Panel or Digital Main CBA.
15. To cancel or to exit from the White Balance Adjustment, press [BACK] button.
Initialize the LCD television:
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [INFORMATION i ] button on the remote control unit.
3. Press [ ] button on the remote control unit to initialize the LCD television.
4. After confirming that “INITIALIZED : OK” appears on the screen, turn the AC switch (on the lower left of the back of the unit) off.
FIRMWARE RENEWAL MODE
Equipment Required
a. USB storage device
b. Remote Control Unit
Firmware Update Procedure
[Check the current version]
1. Press [MENU] button on the remote control unit to display the menu mode.
2. Press [ UP ARROW] or [ DOWN ARROW] to select “Others”, then press [OK] button.
3. Press [ PU ARROW] or [ DOWN ARROW] to select “Software”, then press [OK] button. The current FW version will be displayed.
Preparation
 1. Prepare USB storage device.
2. Copy F/W-file (pkg file) to USB storage device.
Note: Make sure to use the blank USB Storage.
3. Rename the F/W-file’s name to “upgrade.pkg”.
[Update procedure]
1. Turn the AC switch (on the lower left of the back of the unit) off.
2. Insert USB storage device with F/W to TV set.
3. Turn the AC switch on.
4. Updating starts automatically. Red LED flashes.
Note: Do not turn off the TV set and do not remove the USB storage device while this procedure.
5. When updating is completed, the TV set will turn back on automatically.
6. To shift the TV set to standby mode, press [ POWER ] button on the remote control unit.
7. Remove USB storage device from TV set.
8. Press [ ] button again to turn the power on.
9. Press [MENU] button on the remote control unit to display the menu mode.
10. Select “Parental” - “PIN CODE:”.
11. Press [4], [7], [3] and [7] buttons on the remote control unit.
12. Select “Factory Reset” and press [OK] button.
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
Posted By: FRANK at 02:12
TAG: , ,