SANYO LED-46XR123D – HOW TO ENTER Factory Mode – Adjustments _ SMPS Schematic
LED-46XR123D - SANYO LED LCD TV – Factory Mode – Adjustments _ SMPS Schematic
FACTORY MENU [SERVICE MENU]
Connect
power/backlight board assembly, data processing assembly, IR/Key board assembly
correctly, supply with power, turn on the TV set. Check display.
Factory
menu instruction
> Press key INPUT, then press digital keys “2, 5, 8,0” in turn to enter into primary factory
menu.
> Press keys ▲ and ▼ to move cursor to each page of primary factory menu, and then press key OK to enter into sub-menu page.
> Press keys ▲ and ▼ to move cursor upward or downward within any one page.
> Press keys ◄ and ► to do adjustment when move cursor to one item.
> Press key MENU to exit sub-menu page to the superior factory menu.
> Press key EXIT to exit factory menu in any case.
> Press key OK to enter the inferior factory sub-menu.
Factory menu item
> Press keys ▲ and ▼ to move cursor to each page of primary factory menu, and then press key OK to enter into sub-menu page.
> Press keys ▲ and ▼ to move cursor upward or downward within any one page.
> Press keys ◄ and ► to do adjustment when move cursor to one item.
> Press key MENU to exit sub-menu page to the superior factory menu.
> Press key EXIT to exit factory menu in any case.
> Press key OK to enter the inferior factory sub-menu.
Factory menu item
Aging Mode to
be used for aging the TV set; red, green blue and white full screen picture
displays in turn; default setting is OFF;
Factory menu item
Factory menu item
ADC ADJUST to
be used for ADC calibration for VGA and Component.
Factory
menu item
Fac. Channel Preset to be used for factory channel presetting; central signal digital
frequency value for Australia program is set as CH28 (529.5 MHz) and CH33 (564.5
MHz); original digital program presetting could not change if central signal
setting has any modification, so search for digital program manually by perform
item DTV of menu Channel;
Factory menu item
Factory menu item
Color Temp. to be used for white balance adjustment;
Factory menu item: Store Setting Init.
Factory menu item
Factory menu item: Store Setting Init.
Factory menu item
USB
SW Update to
be used for software updating from USB port; when U disk containing updating
software is inserted into USB port, choose the item to perform updating
process;
Factory menu item
Factory menu item
Other Settings include settings of EEPROM Init, MEMC Update, Power mode, MST
DEBUG, ISP MODE, Back-light, SSC, NONLINEAR, Video Quality, Audio Quality, Light
Sensor, Over scan, etc.; no need any adjustment normally.
Factory
menu item
Shipment to be used for initializing user data; Success flag will display
after initialization, then press KEY POWER only to power off the TV set.
Perform EEPROM Init before adjustment for the first time if software has been upgraded or data have been kept in EEPROM.
Perform EEPROM Init before adjustment for the first time if software has been upgraded or data have been kept in EEPROM.
ADC
calibration for D-SUB channel
Switch to D-SUB channel.
> Press key INPUT, and then press digital keys 2, 5, 8, 0 in turn to enter into primary factory menu.
> Move cursor to item ADC ADJUST and press key OK to enter into the inferior sub-menu.
> Input D-SUB signal (VG-849 Timing:856 (1024×768/60 Hz), Pattern:914 Chess Pattern); move cursor to item “MODE”, press keys ▲ and ▼ to choose item “RGB”, then move cursor to item “AUTO ADC” and press key “OK” to perform auto adjustment until prompt “success” displays.
Switch to D-SUB channel.
> Press key INPUT, and then press digital keys 2, 5, 8, 0 in turn to enter into primary factory menu.
> Move cursor to item ADC ADJUST and press key OK to enter into the inferior sub-menu.
> Input D-SUB signal (VG-849 Timing:856 (1024×768/60 Hz), Pattern:914 Chess Pattern); move cursor to item “MODE”, press keys ▲ and ▼ to choose item “RGB”, then move cursor to item “AUTO ADC” and press key “OK” to perform auto adjustment until prompt “success” displays.
ADC
calibration for Component channel
* Switch to Component channel.
* Press key “INPUT”, then press digital keys 2, 5, 8, 0 in turn to enter into primary factory menu;
* Move cursor to item “ADC ADJUST” and press key “OK” to enter into the inferior submenu;
* Input Component signal (VG-849 Timing: 972(1080i), Pattern:918 100% color bar); move cursor to item “MODE”, press keys ▲ and ▼ to choose item “YPbPr”, then move cursor to item “AUTO ADC” and press key “OK” to perform auto adjustment until prompt “success” displays.
* Switch to Component channel.
* Press key “INPUT”, then press digital keys 2, 5, 8, 0 in turn to enter into primary factory menu;
* Move cursor to item “ADC ADJUST” and press key “OK” to enter into the inferior submenu;
* Input Component signal (VG-849 Timing: 972(1080i), Pattern:918 100% color bar); move cursor to item “MODE”, press keys ▲ and ▼ to choose item “YPbPr”, then move cursor to item “AUTO ADC” and press key “OK” to perform auto adjustment until prompt “success” displays.
White
balance adjustment
Unless specified by customer, default settings of COOL color temperature is 12000K and chromatic coordinates is (272、 278); referenced settings of Normal color temperature is 9300K and chromatic coordinates is (285、 293); referenced settings of Warm color temperature is 6500K and chromatic coordinates is (313, 329); Default setting is Normal.
Unless specified by customer, default settings of COOL color temperature is 12000K and chromatic coordinates is (272、 278); referenced settings of Normal color temperature is 9300K and chromatic coordinates is (285、 293); referenced settings of Warm color temperature is 6500K and chromatic coordinates is (313, 329); Default setting is Normal.
Adjustment
procedures
The TV set should be working above 30 minutes to be in a stabler state before adjustment. Use CA-210 BBY channel to adjust white balance;
* Switch to HDMI channel;
* Press key “INPUT”, then press digital keys “2, 5, 8, 0” in turn to enter into primary factory menu;
* Move cursor to item “W/B ADJUST” and press key “OK” to enter into the inferior submenu;
Input HDMI signal (VG-849 Timing: 856(1024×768/60 Hz)， Pattern:921 16 step Gray); move cursor to item “MODE”, press keys ▲ and ▼ to choose item “HDMI”, then move cursor to item “TEMPERTURE” and press keys ▲ and ▼ to choose “COOL”.
Fix “G GAIN”, adjust “R GAIN, B GAIN” to set 14th chromatic coordinates as (272, 278);
Fix “G OFFSET”, adjust “R OFFSET、 B OFFSET” to set 4th chromatic coordinates as (272, 278).
The TV set should be working above 30 minutes to be in a stabler state before adjustment. Use CA-210 BBY channel to adjust white balance;
* Switch to HDMI channel;
* Press key “INPUT”, then press digital keys “2, 5, 8, 0” in turn to enter into primary factory menu;
* Move cursor to item “W/B ADJUST” and press key “OK” to enter into the inferior submenu;
Input HDMI signal (VG-849 Timing: 856(1024×768/60 Hz)， Pattern:921 16 step Gray); move cursor to item “MODE”, press keys ▲ and ▼ to choose item “HDMI”, then move cursor to item “TEMPERTURE” and press keys ▲ and ▼ to choose “COOL”.
Fix “G GAIN”, adjust “R GAIN, B GAIN” to set 14th chromatic coordinates as (272, 278);
Fix “G OFFSET”, adjust “R OFFSET、 B OFFSET” to set 4th chromatic coordinates as (272, 278).
* To
make sure chromatic coordinates of bright scale are (X=272±10， Y=278±10)
and chromatic coordinates of dark scale are (X=272±10，Y=278±10)
during adjusting;
* Move cursor to item “COPY ALL” to copy white balance data to other channels except DTV channel;
* Check if chromatic coordinates of NORMAL and WARM meet the requirements (permitted error of NORMAL bright scale: x±1,±10, permitted error of NORMAL dark scale: x±10，y±10. permitted error of WARM bright scale and dark scale: x±10,y±10); if not, adjust “R_GAIN /B_GAIN/R_OFF/B_OFF” to be up to the requirements and then save the data.
* Move cursor to item “COPY ALL” to copy white balance data to other channels except DTV channel;
* Check if chromatic coordinates of NORMAL and WARM meet the requirements (permitted error of NORMAL bright scale: x±1,±10, permitted error of NORMAL dark scale: x±10，y±10. permitted error of WARM bright scale and dark scale: x±10,y±10); if not, adjust “R_GAIN /B_GAIN/R_OFF/B_OFF” to be up to the requirements and then save the data.
* Perform “Copy All”
for Normal/Warm adjustments except DTV channel.
* Check if chromatic coordinates of other channels meet the requirements, if not, do adjustment for nonstandard channel alone with the same procedures from b) to j) as HDMI channel’s and then save the data.
* Check if chromatic coordinates of other channels meet the requirements, if not, do adjustment for nonstandard channel alone with the same procedures from b) to j) as HDMI channel’s and then save the data.
Switch
to HDMI channel, change to 16-grey-scale program from central signal source,
adjust white balance with the same procedures from e) to g) as HDMI channel’s;
but pay
attention not to perform “COPY ALL”
* Inspect all channels after completing adjustment to check if display is normal.
Refer to the following rule for adjustment
* Inspect all channels after completing adjustment to check if display is normal.
Refer to the following rule for adjustment
B
Gain/Offset: adjust B Gain/Offset downward, coordinates of X and Y will
increase, adjust B Gain/Offset upward, coordinates of X and Y will decrease.
R Gain/Offset: adjust R Gain/Offset will affect X value, but affect Lv value slightly, adjust R Gain/Offset upward, coordinates of X will increase, adjust R Gain/Offset downward, coordinates of X will decrease.
G Gain/Offset: adjust G Gain/Offset will affect Y value, and affect Lv value greatly, adjust G Gain/Offset upward, coordinates of Y will increase, adjust G Gain/Offset downward, coordinates of Y will decrease.
Note: Sanyo customer requires that default color temperature is Normal, adjust white balance of color temperature Normal and Cool in Dynamic picture mode; for other customers, please adjust white balance of color temperature Cool in Dynamic picture mode.
R Gain/Offset: adjust R Gain/Offset will affect X value, but affect Lv value slightly, adjust R Gain/Offset upward, coordinates of X will increase, adjust R Gain/Offset downward, coordinates of X will decrease.
G Gain/Offset: adjust G Gain/Offset will affect Y value, and affect Lv value greatly, adjust G Gain/Offset upward, coordinates of Y will increase, adjust G Gain/Offset downward, coordinates of Y will decrease.
Note: Sanyo customer requires that default color temperature is Normal, adjust white balance of color temperature Normal and Cool in Dynamic picture mode; for other customers, please adjust white balance of color temperature Cool in Dynamic picture mode.
Function check (TV functions)
Input central signal to RF port, enter into menu Channel first, then search for programs automatically and check if there is any omitted program; check the speakers output and the picture display;
Input central signal to RF port, enter into menu Channel first, then search for programs automatically and check if there is any omitted program; check the speakers output and the picture display;
Component
port
Input Component signal from VG-849 with formats listed as Table separately, check picture and sound in the case of power-on, switching channel, changing mode, etc.
Input Component signal from VG-849 with formats listed as Table separately, check picture and sound in the case of power-on, switching channel, changing mode, etc.
D-SUB
port
Input D-SUB signal from VG-849 with formats listed as Table separately, check picture and sound; if H./V. of picture displays abnormally, enter into main menu Picture > Screen > Auto Adjust to perform auto calibration.
Input D-SUB signal from VG-849 with formats listed as Table separately, check picture and sound; if H./V. of picture displays abnormally, enter into main menu Picture > Screen > Auto Adjust to perform auto calibration.
HDMI
port
HDMI port supports all signal formats supported by Component port and D-SUB port ), furthermore, it can also support signal with formats listed as Tables (video and audio combination). Check picture and sound in the case of power-on, switching channel, changing mode, etc.
HDMI port supports all signal formats supported by Component port and D-SUB port ), furthermore, it can also support signal with formats listed as Tables (video and audio combination). Check picture and sound in the case of power-on, switching channel, changing mode, etc.
USB
port. PVR function
Insert a formatted U disk in which recorded programs have been saved; press key “Record List” to choose and play one program, check picture, sound and other functions;
Media playing function
Insert a U disk kept files of picture, sound and video, check picture, sound and other functions;
Supported media formats as below:
Photo：JPEG – BMP - PNG
Video：H.264 - MPEG-1 - MPEG-2, VC-1, FLV
Audio：WMA, MP3, M4A (AAC)
Insert a formatted U disk in which recorded programs have been saved; press key “Record List” to choose and play one program, check picture, sound and other functions;
Media playing function
Insert a U disk kept files of picture, sound and video, check picture, sound and other functions;
Supported media formats as below:
Photo：JPEG – BMP - PNG
Video：H.264 - MPEG-1 - MPEG-2, VC-1, FLV
Audio：WMA, MP3, M4A (AAC)
Music port(depending on different models
whether contain the port or not）
Input audio signal to back VGA MUSIC/AUDIO In port from audio output equipment, check audio output is normal or not.
Other functions check
a. Check timing on/off, sleeping time off, picture/sound mode, OSD, stereo, digital audio port, etc,;
b. Check pure digital audio programs (RADIO) ;
c. Check logical channel number (LCN);
d. Check HDMI ARC;
e. Check HDMI CEC;
f. Check OAD for special customer.
Input audio signal to back VGA MUSIC/AUDIO In port from audio output equipment, check audio output is normal or not.
Other functions check
a. Check timing on/off, sleeping time off, picture/sound mode, OSD, stereo, digital audio port, etc,;
b. Check pure digital audio programs (RADIO) ;
c. Check logical channel number (LCN);
d. Check HDMI ARC;
e. Check HDMI CEC;
f. Check OAD for special customer.
User Menu Setting before Ex-factory
Enter into Factory Menu and choose “Shipment” to perform presetting before ex-factory; Main procedures are described as follow:
a. Clear out all programs;
b. Clear out information of VCHIP， parent control, etc.;
c. Default user analog parameter setting;
d. Recover default password;
e. Set Menu Language as English；
f. Set Power mode as Standby.
Enter into Factory Menu and choose “Shipment” to perform presetting before ex-factory; Main procedures are described as follow:
a. Clear out all programs;
b. Clear out information of VCHIP， parent control, etc.;
c. Default user analog parameter setting;
d. Recover default password;
e. Set Menu Language as English；
f. Set Power mode as Standby.
CLICK ON THE PICTURES TO MAGNIFY
