LG 42PT350R _ 42PT351R _ 42PT350R-TD_42PT351R-TC _ OPTION ADJUSTMENT FOLLOWING BOM _ EDID D/L METHOD _ POWER VOLTAGE ADJUSTMENT_AREA OPTION ADJUSTMENT
PCB ASSEMBLY ADJUSTMENT
OPTION ADJUSTMENT
- Tool Option
- Area Option
- Option 1
- Option 2
- Option 3(Available for EU & Non EU model)
- # Profile: Must be changed the option value because being different with some setting value depend on module, inch and market
- # Equipment : Adjustment Remote Controller.
- Push the IN-START key in the Adjust R/C.
- Enter Password number. The value of Password is “0 0 0 0”.
- Input the Option Number that was specified in the BOM, into the Shipping area.
- Select “Tool Option” by using UP/DN (CH+/-) key, and press the number key(0~9) consecutively. (ex) If the value of Tool Option1 is 4, input the data using number key “4”.
- if it is EU model ( such as 42/50PJ**R-ZA ), select “Area option” by using UP/DN (CH+/-) key , and press the number key(0~9) consecutively. (ex) If the value of Area Option is 40, input the data using number key “40”
Caution: Don’t Push “IN-STOP” key after PCB assembly adjustment.
PP01A/B/C Tool option:
Model: 42PT250R-TA
Tool option: 13
Area Option: 1
EDID D/L METHOD
- After software D/L or PCBA manufacturing, you can download EDID Data.
- When you adjust Tool Option, H6 Model EDID download process is executed automatically.
- If the model don’t have HDMI 3, HDMI 3 will be disappeared at OSD Window.
- [Caution]: When you adjust tool option, don’t connect HDMI or Dsub cable. If you connect some cable, EDID D/L process will be failed.
ADJUSTMENT METHOD
Before PCBA
check, have to change the Tool option and Area option.
# About PDP
- After done all adjustments, Press IN-START button and compare Tool option and Area option value with its BOM, if it is correctly same then Change “RF mode” and then unplug the AC cable.
- If it is not same, then correct it same with BOM and unplug AC cable.
- For correct it to the model’s module from factory JIG model.
# Don’t push The IN-STOP KEY after completing the function inspection.
EDID DATA
Caution
- Never Use the cable( HDMI or D-sub cable) for EDID Writing.
- Automatically PP01A/B/C Model EDID download process is executed when you adjust Tool Option.
INTCH
|
|
TOOL
|
|
SIDE AV
|
0/1
|
HDMI
|
0/1/2/3
|
Side HDMI
|
0/1
|
COMP2
|
0/1
|
RGB
|
0/1
|
RS232C
|
0/1
|
Local Key
|
0 (7KEY) / 1
(8KEY)
|
LED TYPE
|
0 (RED) / 1
(RED/White) / 2 (Reserve)
|
USB TYPE
|
0 (NONE) / 1
(PHOTO, MUSIC)
/ 2 (PHOTO,
MUSIC, DivX)
|
POWER ASSEMBLY VOLTAGE ADJUSTMENT
- Connect + terminal of D. M..M. to Va pin of P811, connect -terminal to GND pin of P811.
- After turning VR502, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top ( deviation ; ± 0.5 V)
AREA OPTION ADJUSTMENT
Area Option
Adjustment following BOM
(Including SKD
models )
Tool Option
Area Option
Option 1
Option 2
Option 3 ( Available for EU & Non EU model )
- Push the IN-START key in the Adjust R/C.
- Enter Password number. The value of Password is “0 0 0 0”.
- Input the Area Option Number that was specified in the BOM, into the Shipping area.
- Select “Area Option” by using UP/DN (CH+/-) key, and press the number key(0~9) consecutively. (ex) If the value of Area Option 40, input the data using number key “40”.
Caution: Although it is
SKD model, adjust area option in SET assemmbly process. Don’t Push “IN-STOP” key after PCB assembly adjustment.
