ONKYO TX-NR545 AV Receiver - Factory reset procedure - Self diagnosis - Firmware checking and updating procedure - Troubleshooting - AV receiver Repair and service
Category: AV Receiver Repair and Service
Contents of this article
- Factory Resetting Procedure
- Firmware updating Procedure
- Troubleshooting
ONKYO TX-NR545
Resetting the Unit
# How
to reset:
Step:1
While holding down CBUSAT on the main unit (note that
step 2 must be performed with this button pressed down)
Step:2
Press ONISTANDBY on the main unit. ("Clear"
appears on the display and the unit returns to standby.)
# Do not unplug the power cord until "Clear"
disappears from the display.
#
How to reset the remote controller:
Step:1
While holding down RECEIVER on the remote controller,
press Q until the remote indicator stays lit (about 3 seconds).
Step:2
Within 30 seconds, press RECEIVER again.
Self-diagnostics
This function is For avoiding the rupture of electrolytic
capacitors with amplifier circuit failure during power-ON.
Operation
of Self—diagnostic
Self-diagnostic will start at the timing of next power on,
after goes to the protect mode by Current detection or DC voltage detection.
Only On/Standby key could work in this mode. Also remote
control does not work.
However, the CLEAR operation is enabled.
During Self-diagnostic, the power supply for amplifier
circuit become low voltage state(SEC1-LOW), and the speaker relay will be
turned off. Then, MPU will check each amplifier circuits internally by entering
the test signal (20 kHz,-20 dBFS sine wave) to each channel from DSP.
MPU will judge the amplifier circuit is good or not from
VOLH value.
The normal range of VOLH value is 0.04 V < VOLH <
0.20 V.
If VOLH value is in the out of this range, it will be
judged as NG (No good).
No
problem found
When protected by current detection, and no problem
found, "CHECK SP WIRE“ will be displayed in this State, Only the On/Standby
key is effective. And it do not anything for 3 minutes, unit goes into stand by
automatically.
When protected by a DC voltage detection, and no problem
found, unit goes into normal operation.
Problem
found
When judged as there is a problem on any channel, the
information of channel that has a problem will be displayed. In this State, Only
the On/Standby key is effective. Also remote control does not work. if do not anything
for 3 minutes, unit goes into standby automatically. This state will keep also
after unit turn on/off, or AC unplugged.
The power supply for the amplifier becomes low voltage
state and the speaker relay will be turned on.
Repair
Process and How to Confirm
Confirmation
of the protect cause
While NG channel is displayed, You can confirm the
protect cause by following the step below
1. Press the Enter button
2. The protect cause are displayed for 5 seconds.
Please check the around of those amplifier circuit and
repair it.
Clear
of NG CH information
After repair, you can clear NG CH information by
following the steps below.
1. Press the On!Standby key while pressing the Enter key.
2. Display as in the right figure appears.
3. Unit goes into Standby automatically after 5 seconds.
Self-diagnostic will start again at the timing of next
power on.
By this, You can verify whether repair was properly or
not.
If problem found after repair, please re-check the around
of its circuit.
Cancel
of Self-diagnostic
You can cancel this mode by clear operation (press
Standby key while pressing CBL/SAT key)
After cancel this mode, receiver will be started as
normal operation.
How
to check Firmware Version & Preparation of Update
Step1 : [DISPLAY] + [ON/STANDBY] x 2
Main Firmware Version will appear on the main unit’s
display.
Step2 : [TONE +]
NET Firmware Version will appear on the main unit’s
display.
Step3 : [TONE +]
DSP Firmware Version will appear on the main unit's
display.
Step4 : [TONE +]
VIDEO Firmware Version will appear on the main unit’s
display.
Step5 : [TONE +]
OSD Firmware Version will appear on the main unit’s
display.
Step6 : [TONE +]
V8100 Firmware Version will appear on the main unit’s
display ( DTR-40.7 only)
Preparation
of Update
1. Connect the USB storage device to your PC. If there is
any data in the USB storage device, remove it.
2. Download the firmware file (package file) from the Onkyo
FTP-server.
However European service partners should download the firmware
file (package file) from the ExtraNet.
Onkyo FTP-server: onkyo.co.jpf_servicefwalTX-NR545
ID and Password are those we informed when changed.
Filename is as follows: ON KAVROO1 D_****************.zip
Unzip the downloaded file. A following file is created.
ONKAVROO1 D_************.of1
ONKAVROO1 D_************.of2
ONKAVROO1 D_************.of3
ONKAVROO1 D_************.of4
ONKAVROO1 D_************.of5
3. Copy it to the USB storage device. Be careful not to
copy the zip file
4. Remove the USB storage device from your PC.
How
to update (service mode)
Overwriting is also possible.
1,Turn on the unit. It takes some time to start after you
switch on the unit.
2.Select the USB input source.
3.Connect the USB storage device to USB port on the unit.
Wait until Initializing of USBINET finishes.
4.Hold down [DISPLAY] button and then press [ONISTANDBY]
button twice.
Main version will be displayed, and HYBRID STANDBY
indicator will start to flash.
5.Press [RETURN] button. “NET -> ALL_D" will be
displayed.
6.Select "USB -> ALL_D" by [PRESET(left/right)]
cursors and [TUNING(up/down)] cursors, then press [ENTER] button, updating will
begin.
7.Wait until update is completed. When the update ends,
"Completed!" is displayed (if you leave it, it automatically turns
standby mode. )
8.Press [ON/STANDBY] button, and the unit turns on.
9.Check the new FW version number.
<Note>
If the procedure might not be successful, please select
"USB -> ALL_M”.
TROUBLESHOOTING
No
Sound
No sound from connected player
# Chose input selector which is assigned to connected
input terminal ?
# Isn't muting on ?
No
sound from connected TV
# Chose wrong input selector ?
# Connect to this model's HDMI OUT terminal from TV by
HDMI cable ?
# When TV supports ARC function, connect to his model's
HDMI OUT terminal from TV's HDMI input terminal for ARC function ?
# When TV doesn't support ARC function, connect TV to
this model with optical cable etc. ?
# Isn't muting on ?
No sound from some connected loudspeaker(s)
# No sound loudspeaker(s) config is enabled ?
No
sound from all connected TV or B|u—ray player etc.
# After chose loudspeaker volume level setting, test tone
is OK ?
No
problem about above items
# Unplug power cord
After 10 seconds, connect power cord again
# Reset this model
NO
Picture
In
general
# Connection cable is bent , twisted or damaged ?
# Input is switched on TV ?
No
picture from connected player by HDMI input terminal
# Chose input selector which is connected to player ?
# Listening mode is not Pure Audio ?
# Don't use HDMI—DVI adaptor. From personal computer ?
No
picture from connected player by component video terminal
# Output to TV connected to component video out terminal
from player's picture connected to the composite video input terminals ?
No problem about above items
# Unplug power cord
After 10 seconds connect the power cord again
Reset this model
No
Power
In
general
# Doesn't be connection cable bent, be it twisted and be
it damaged?
There
is time when indication on the front panel doesn't just light up.
# Please check the connecting cord of a DISPLAY PCB.
No
problem about above items
# Unplug power cord
After 10 seconds, connect power cord again
# Reset this model
