PANASONIC DMP-BD35 BLU RAY SERVICE MODE ERROR CODES AND POWER SUPPLY CIRCUIT
PANASONIC DMP-BD35
BLU RAY
SERVICE MODE ERROR CODES AND POWER SUPPLY CIRCUIT
Taking out the Disc from BD Drive
Unit when the Disc cannot be ejected by OPEN/CLOSE
button
Forcible Disc Eject
When the power can be turned off.
1. Turn off the power and press [PAUSE] and [OPEN/CLOSE] keys on the front panel simultaneously for 5 seconds.
When the power can not be turned off.
1. Press [POWER] key on the front panel for over 10 seconds to turn off the power forcibly, and press [PAUSE] and [OPEN/ CLOSE] keys on the front panel simultaneously for 5 seconds.
When the Forcible Disc Eject can not be done.
1. Turn off the power and pull out AC cord.
2. Remove the Top Case.
3. Insert Eject Pin (JZS0484) into the hole on the bottom of BD Drive and slide the Eject Pin in the direction of the arrow to eject tray slightly.
Forcible Disc Eject
When the power can be turned off.
1. Turn off the power and press [PAUSE] and [OPEN/CLOSE] keys on the front panel simultaneously for 5 seconds.
When the power can not be turned off.
1. Press [POWER] key on the front panel for over 10 seconds to turn off the power forcibly, and press [PAUSE] and [OPEN/ CLOSE] keys on the front panel simultaneously for 5 seconds.
When the Forcible Disc Eject can not be done.
1. Turn off the power and pull out AC cord.
2. Remove the Top Case.
3. Insert Eject Pin (JZS0484) into the hole on the bottom of BD Drive and slide the Eject Pin in the direction of the arrow to eject tray slightly.
Self-Diagnosis and Special Mode Setting
Self-Diagnosis Functions
Self-Diagnosis Function provides information for errors to service personnel by Self-Diagnosis Display when any error has
occurred.
U**, H** and F** are stored in memory and held.
You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
Self-Diagnosis Functions
Self-Diagnosis Function provides information for errors to service personnel by Self-Diagnosis Display when any error has
occurred.
U**, H** and F** are stored in memory and held.
You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
ERROR CODES AND DESCRIPTION
Error Code
|
Diagnosis contents
|
Description
|
U30
|
Remote
control code error
|
Display
appears when main unit and remote
controller codes are not matched. |
U59
|
Abnormal
inner temperature
detected |
Display
appears when the drive temperature
exceeds 70°C. The power is turned off forcibly. For 30 minutes after this, all key entries are disabled. (Fan motor operates at the highest speed for the first 5 minutes. For the remain ing 25 minutes, fan motor is also stopped.) The event is saved in memory as well. |
U71
|
HDMI
incompatible error
(HDCP incompatible) |
Display
this error when the equipment (com
patible with DVI such as TV, amplifier etc.) connected to the unit by HDMI is incompatible with HDCP. *HDCP = High-bandwidth Digital Content Protection |
U72
|
HDMI
connection error
(communication error) |
This
error is displayed when there are any
communication problems with the unit and the equipments (TV, amplifier etc.) connected to the unit by HDMI. (or when there is a problem with the HDMI cable) |
U73
|
HDMI
connection error
(authentication error) |
when
authentication error occurs while the
equipments (TV, amplifier etc.) are connected by HDMI. (or when there is a problem with the HDMI cable) |
F99
|
Hang-up
|
Displayed
when communication error has
occurred between Main microprocessor and Timer microprocessor. |
H19
|
Inoperative
fan motor
|
When
inoperative fan motor is detected after
powered on, the power is turned off automatically. The event is saved in memory. |
F00
|
No
error information
|
Initial
setting for error code in memory
(Error code Initialization is possible with error code initialization and main unit initialization.) |
F34
|
Initialization
error
|
When
initialization error is detected after
starting up main microprocessor, the power is turned off automatically. The event is saved in memory. |
F58
|
Drive
hardware error
|
When
drive unit error is detected, the event is
saved in memory. |
Service
Mode
Setting every kind of modes for servicing.
When the power is off, press [PAUSE], [PLAY] and [SETUP (Remote Controller)] keys simultaneously for 5 seconds.
When the power is off, press [PAUSE], [PLAY] and [SETUP (Remote Controller)] keys simultaneously for 5 seconds.
Rating
password
The audiovisual level setting password is initialized to Level
8.
Open the tray, and press [SKIP REV (Remote Controller)] and
[PLAY] simultaneously for 5 seconds.
BD-ROM
history cleaning
Persistent Storage of BD-ROM standard is cleaned. Screen
display: [The player's history data has been cleared] is displayed for five
seconds.
When the power is on, disc is not in tray, press [STOP] and
[POWER (Remote Controller)] keys simultaneously for 5 seconds.
Forced
disc eject
Removing a disc that cannot be ejected. The tray will open
and unit will shift to P-off mode.
While Demonstration Lock is being set, this Forced disc eject function is not accepted.
While Demonstration Lock is being set, this Forced disc eject function is not accepted.
When the power is off, press [PAUSE] and [OPEN/CLOSE] keys simultaneously
for 5 seconds.
Forced
power-off
When the power button is not effective while power is ON,
turn off the power forcibly.
Press [POWER] key over than 10 seconds.
Progressive
initialization
The progressive setting is initialized to Interlace.
When the power is on (SS mode), press [STOP] and [PLAY]
simultaneously for 5 seconds.
Default
setting
The date of Menu, Mode and EEPROM setting, etc. is set to
the default condition in factory
When the power is off, press [PAUSE], [POWER] and [OPEN/ CLOSE]
simultaneously for 5 seconds
POWER SUPPLY CIRCUIT
