REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Thursday 28 March 2019

PANASONIC PLASMA TV - TH-P50XT50G - SERVICE MODE - LED BLINKING CODES

PANASONIC PLASMA TV - TH-P50XT50G - SERVICE MODE - LED BLINKING CODES


Applicable to - Panasonic TH-P50XT50A TH-P50XT50D TH-P50XT50G TH-P50XT50K TH-P50XT50M TH-P50XT50P TH-P50XT50S TH-P50XT50V
Service Mode - Service Tool Mode - Data-copy - LED Blinking Codes details
HOW TO ENTER SERVICE MODE

After exchange parts, check and adjust the contents of adjustment mode.
While pressing [VOLUME ( - )] button of the main unit, press [i] button of the remote control three times within 2 seconds.

Note: Service Mode cannot be entered when 3D signal input.  Input 2D signal to enter Service Mode.
KEY COMMANDS
1 button...Main items Selection in forward direction
2 button...Main items Selection in reverse direction
3 button...Sub items Selection in forward direction
4 button...Sub items Selection in reverse direction
RED button...All Sub items Selection in reverse direction
GREEN button...All Sub items Selection in forward direction
VOL button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
Contents of adjustment mode
* Value is shown as a hexadecimal number.
* Preset value differs depending on models.
After entering the adjustment mode, take note of the value in each item before starting adjustment.
PRE-SET DATA VALUES
Option - Mirror
Picture can be reversed left and right or up and down.
00 : Default (Normal picture is displayed)
01 : Picture is reversed left and right.
02 : Picture is reversed up and down.
If the defective symptom (e.g. Vertical bar or Horizontal bar) is moved by selection of this mirror, the possible cause is in A-board.
SERVICE TOOL MODE
Select [SRV-TOOL] in Service Mode.
Press [OK] button on the remote control.
Display of SOS History
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.  This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory shipment setting].
POWER ON TIME/COUNT
Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3 sec.
Time : Cumulative power on time, indicated hour : minute by decimal
Count : Number of ON times by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.
Exit
Disconnect the AC cord from wall outlet.
DRV Check - USBHDD Check
Select [DRV Check - USBHDD Check] in Service Mode.
Press [OK] button on the remote control for more than 3 seconds.
Hotel mode
In order to display the Hotel mode setup menu: While pressing [VOLUME (-)] button of the main unit, press [AV] button of the remote control three times within 2 seconds.
To exit the Hotel mode setup menu: Disconnect AC power cord from wall outlet.
Data Copy by SD Card
Board replacement (Copy the data when exchanging A-board)
When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board.
Hotel (Copy the data when installing a number of units in hotel or any facility)
When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and then copy to other TVs.
Preparation
Make pwd file as startup file for (a) or (b) in a empty SD card.
> Insert a empty SD card to your PC.
> Right-click a blank area in a SD card window, point to New, and then click text document. A new file is created by default (New Text Document.txt).
> Right-click the new text document that you just created and select rename, and then change the name and extension of the file to the following file name for (a) or (b) and press ENTER. File name:
a For Board replacement : boardreplace.pwd
b For Hotel : hotel.pwd
Note:
Make only one file to prevent the operation error.
No any other file should not be in SD card.
Data copy from TV set to SD Card
> Turn on the TV set.
> Insert SD card with a startup file (pwd file) to SD slot.  On-screen Display will be appeared according to the startup file automatically.
> Input a following password for (a) or (b) by using remote control.
a For Board replacement: 2770
b For Hotel: 4850
Data will be copied from TV set to SD card. It takes around 2 to 6 minutes maximum for copying.
> After the completion of copying to SD card, remove SD card from TV set.
> Turn off the TV set.
Note:
Following new folder will be created in SD card for data from TV set.
a For Board replacement : user_setup
b For Hotel : hotel.
Data copy from SD Card to TV set
> Turn on the TV set.
> Insert SD card with Data to SD slot.  On-screen Display will be appeared according to the Data folder automatically.
> Input a following password for (a) or (b) by using remote control.
a For Board replacement : 2771
b For Hotel : 4851
Data will be copied from SD card to TV set.
> After the completion of copying to SD card, remove SD card from TV set.
a For Board replacement: Data will be deleted after copying (Limited one copy).
b For Hotel: Data will not be deleted and can be used for other TVs.
> Turn off the TV set.
Depending on the failure of boards, function of Data copy for board replacement does not work.
This function can be effective among the same model numbers.
Power LED Blinking timing chart
Information of LED Flashing timing chart.
When an abnormality has occurred the unit, the protection circuit operates and reset to the standby mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
CLICK ON THE PICTURES TO ZOOM IN
Posted By: FRANK at 04:53
TAG: , , , , ,