REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:

- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Saturday 9 March 2019

SHARP LC-32LE210E/RU - LC-32LE210EB/RUB - LC-32LE220E/RU - LC-32LE220EB/RUB - LC-32LB220E/RU - LC-32LB220EB/RUB - LC-32LS220E/RU - LC-32LS220EB/RUB SERVICE MODE AND POWER SUPPLY CIRCUIT

SHARP LC-32LE210E/RU - LC-32LE210EB/RUB - LC-32LE220E/RU - LC-32LE220EB/RUB - LC-32LB220E/RU - LC-32LB220EB/RUB - LC-32LS220E/RU - LC-32LS220EB/RUB SERVICE MODE AND POWER SUPPLY CIRCUIT


SHARP LC-32LE210E/RU - LC-32LE210EB/RUB - LC-32LE220E/RU - LC-32LE220EB/RUB - LC-32LB220E/RU - LC-32LB220EB/RUB - LC-32LS220E/RU - LC-32LS220EB/RUB 

LED LCD

SERVICE MODE AND POWER SUPPLY CIRCUIT 


Entering and exiting the adjustment process mode.
 Standard method.
1. By key-unit.
1. Unplug the AC power cord.
2. Press and hold “V-” and “AV (INPUT ) ” keys, simultaneously, and then plug the AC power cord.
3. “K” appears on the screen.
4. Press and hold “V-” and “P-” keys, simultaneously.
5. “SHARP FACTORY MENU” appears .

6. Unplug the AC power cord to exit of adjustments process.
2. By own R/C
1. Turn on the TV set.
2. Press “AV(INPUT)”,”2”,”5”, “8”, “0” (the time is limited to 5 sec. approx., for enter this code).
3. “SHARP FACTORY MENU” appears.

4. Press “OK” on lines 5 >12 to go to submenu.
5. Press “MENU” to return to main menu.
6. Press “END” to exit of adjustments mode.
RGB SCART ADC
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “UP”until selecting “MODE” option.
8. Press “RIGHT”until selecting “RGB”.
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts.
11. “SUCCESS” appears when the adjustments Finish.
12. Exit of Service mode.
COMPONENTS ADC
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “UP”until selecting “MODE” option.
8. Press “RIGHT”until selecting “YPbPr(SD)” or “YPbPr(HD)”
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts.
11. “SUCCESS” appears when the adjustments Finish.
Note: both SD and HD are adjusted.
12. Exit of Service mode.
PC IN RGB ADC
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “Ÿ”until selecting “MODE” option.
8. Press “RIGHT”until selecting “PC-RGB”.
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts
11. “SUCCESS” appears when the adjustments  Finish.
12. Exit of Service mode
White Balance Adjustment
Condition: AV MODE= Dynamic (backlight at max.).
• Adjustments reference device: Minolta CA-210
• Adjustments target: x=0.272, y=0.277
High: adjustments spec ±0.001, inspection spec: ±0.002
Low: adjustments spec ±0.002, inspection spec: ±0.004
1. Press “DOWN” until selecting “GAMMA” option.
2. Press “OK”.
3. “GAMMA” menu appears.
4. Press “DOWN” until selecting “MGAMMA RESET”.
5. Press “RIGHT”, to restore default values.
6. “MGAMMA RESET SUCCESS” appears.
7. Press “P+” to increase one page.
8. Press “1”, appears “Internal Adjustments Pattern 1”.
9. Hold the default value for “MGAMMA G1”.
(Note: next, try to get the (x, y) adjustments target, changing “MGAMMA R1” and “MGAMMA B1” as follow).
10. Press “DOWN” until selecting “MGAMMA R1”.
11. Press “LEFT/RIGHT” until you obtain the desired value.
12. Press “MENU” to return to previous menu.
13. Press “DOWN” until selecting “MGAMMA B1”.
14. Press “LEFT/RIGHT” until you obtain the desired value.
15. Press “MENU” to return to previous menu.
(Note: In case of not being possible to achieve the desired (x, y) target, try to get it by changing also the “MGAMMA G1”)
16. Press “2”, appears “Internal Adjustments Pattern 2”.
17. Repeat from step 9 to 15 for the “MGAMMA R2” and “MGAMMA B2”.
18. Press “3”, appears “Internal Adjustments Pattern 3”.
19. Repeat from step 9 to 15 for the “MGAMMA R3” and “MGAMMA B3”.
20. Press “4”, appears “Internal Adjustments Pattern 4”.
21. Repeat from step 9 to 15 for the “MGAMMA R4” and “MGAMMA B4”.
22. Press “5”, appears “Internal Adjustments Pattern 5”.
23. Repeat from step 9 to 15 for the “MGAMMA R5” and “MGAMMA B5”.
24. Press “6”, appears “Internal Adjustments Pattern 6”.
25. Repeat from step 9 to 15 for the “MGAMMA R6” and “MGAMMA B6”.
26. Press “DOWN” until selecting “MGAMMA WRITE”.
27. Press “RIGHT ”, to save the new values.
28. “MGAMMA WRITE SUCCESS” appears.
NOTE: For activating the W/B flag, only is necessary to send the order MGAMMA WRITE. After this action, the “W” W/B flag will change to “1”.
Initialization to factory setting
1. Enter in Service mode.
2. Press “DOWN” or “UP” key until selecting INIT.
3. Press OK key.
4. INIT menu appears and “Factory init” option is selected.
5. Press “LEFT” or “RIGHT” until selecting the option desired (EURO/RUSSIA/SWEDEN/UK/EAST EUROPE).
6. Press OK key and initialization starts.
7. OK, EURO message appears for EURO option when the setting is complete.
OK, RUSSIA message appears for RUSSIA option when the setting is complete.
OK, SWEDEN message appears for SWEDEN option when the setting is complete.
OK, UK message appears for UK option when the setting is complete.
OK, EAST EUROPE message appears for EAST EUROPE option when the setting is complete.
Note: Never turn the power off during initialization.
The following settings will be back to their factory ones.
• User settings
• Channel data (e.g. broadcast frequencies)
• Maker option setting
• Password data
POWER SUPPLY CIRCUIT 
Power Supply Diagram LC32LE210/220E MODELS (AUO PANEL) RDENCA409WJQZ (1 / 2)


Power Supply Diagram LC32LE210/220E MODELS (AUO PANEL) RDENCA409WJQZ (2 / 2)


Power Supply Diagram LC32LE210/220EB MODELS (CMI PANEL) RDENCA411WJQZ (1 / 1)
CLICK ON THE IMAGES TO ZOOM IN