REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Friday, 1 March 2019

SHIVAKI FL2660E - SHIVAKI FL3260E - HOW TO ENTER SERVICE MODE - ADJUSTMENTS

Shivaki FL2660E - Shivaki FL3260E - How to enter service mode - adjustments

How to enter Service Mode - Adjustment procedure - Shivaki LCD TVs.  Shivaki FL2660E – Shivaki FL3260E
There are two ways to enter the service mode to these sets.
Service Mode (Factory Mode)
1.Press the [stand-by] button on the remote control. The LCD-TV will shutdown with red lamp lighted; Press it again, the TV will recover.
2. Receive PHILIPS（SECAM/BG，PAL/ BG）Test signal, check picture and sound is all right.
3. Press [P+] or[P-]button to select the program channels forwards or backwards on front panel.
4. Press [V+] or [V-] button to adjust the volume of the speakers on front panel.
5. Press the [SOURCE] button continuously, “TV, AV, SVIDEO, SCART, HEMI, PC and Multimedia are the eight program sources that will be selected in turn on front panel.
6. Press [MENU] button， the menu display normally on front panel.
7. Press the [MENU] button on the remote control, press the 8222 (number button) again, the LCD-TV will be set to the factory mode, display [M] on screen.
Factory mode (Service Mode)
Press the Green button on the remote control to appear an OSD Menu, and then press OK button for about 5 seconds.
The factory setting menu will appear on the screen.  
To exit the factory mode, press the Exit button.
White balance adjust
1.Press the [MENU] button on the remote control ， press the 8222(number button) again, the receiver will be set to the factory mode, display [M] on screen.
2. In the VGA mode to white balance adjust
1) Press the [SOURCE] button to select VGA mode.
2)Signal input: Timing: 1024x768 60HZ, pattern :16 Gray Pattern
3)Enter factory mode
4)Press the [OK] button to select "Auto Color Setting”, Press the [OK] button.
3. In the YPbPr mode to white balance adjust
1) Press the [SOURCE] button to select YPbPr mode.
2)Signal input: Timing: 720P pattern : 100% color bar
3)Enter factory mode
4)Press the [OK] button to select "Auto Color Setting”, Press the [OK] button.
Check AV input and SVIDEO input
1.Press the “SOURCE” button on the remote control to select Video S-video to get the AV input.
2. AT the station Video and Audio1 signal are inputted from DVD player, check the picture and sound are all right.
3. AT the station S-video and Audio1 signal are inputted from DVD player, check the picture and sound are all right.
NOTE: The Video ( Audio1) and S-video( Audio1) socket can't be connected at the same time.
Check YPbPr input
1.Press the “SOURCE” button on the remote control to select Pr Pb” to get the program input.
2. AT the station Y Pr Pb and Audio2 are inputted from DVD player, check the picture and sound are all right.
Check SCART1 input and output
Check SCART1 input
1. Receiving SCART1 single separate in TV and AV mode, the TV will precedence change to SCART1 mode, checking picture and sound is all right.
2. Receiving RGB single, checking picture and sound is all right.
3. Receiving VIDEO single, checking picture and sound is all right.
Check SCART1 output
Receiving a TV signal, connect the SCART1 input socket of monitor with the SCART1 output socket of receiver, the picture and sound of monitor is all right.
*In the USB mode, no precedence to SCART mode.
Check SCART2 input and output
Check SCART2 input
1. Receiving SCART2 single separate in TV and AV mode, the TV will precedence change to SCART2 mode,checking picture and sound is all right.
2. Receiving SC single, checking picture and sound is all right.
3. Receiving VIDEO single, checking picture and sound is all right.
Check SCART2 output
Receiving a TV signal, connect the SCART2 input socket of monitor with the SCART2 output socket of receiver,the picture and sound of monitor is all rigth.
*In the USB mode, no precedence to SCART mode.
Check VGA input
1.Press the “SOURCE” button on the remote control to select “VGA” to get the program input.
2. AT the station HD signal and Audio2 are inputted from HD annunciate, check the picture and sound are all right.
Check HDMI input
1.Press the “SOURCE” button on the remote control to select HDMI1 andHDMI2 to get the program input.
2. The HD signal is inputted from HD annunciate, picture is all right.
Check USB input
1Press the “SOURCE” button on the remote control to select “Multiedia” to get the program input.
2 Press the OK key to enter Multimedia menu.
3 Use Up/Dn; to move cursor to relevant item and press OK to select the file.
Support file:
MPEG1:DAT/MPG/VOB
MPEG2:DAT/MPG/VOB
MPEG4:AVI/VID/MP4
Real media: RM/RMVB
JPEG
TXT
MP3/WMA
Note: when use portable hard disk you should take a adapter for portable hard disk (portable hard disk only support FAT32 format)
Check Headphone output
1.Receive PHILIPS（PAL/ BG or SECAM/BG）test signal, checking picture and sound is all right, and simultaneity the speaker is mute.
Checking function
1.The AC power is switched on, the light will turn blue and then the receiver comes into normal working state.
2.Press the [MENU] button on the remote control, press the [P+] or [P-] buton to select [Preset]
3.Press [V+] to enter the Installation submenu, press the [P+] or [P-] to select [Auto Search] and then press [V+],checking auto search is all right.
4. Press the PMODE button continuously on remote control, the picture mode “Standard - Hi-light – Soft – User – Cinerama – Sports - Vivid” is selected in sequence and check brightness of picture
changing is normal.
5.Press the SMODE button continuously on remote control, the sound mode “Standard – Rock – POP – Live – Dance – Techno – Classic – Soft - User” is selected in sequence and checking sound changing is normal.
6. Receive PHILIPS (PAL, SECAM/BG） 16:9 signal, checking the size of horizontal and vertical is all right.
7. Receive signal (content of sound contain NICAM) press the [Ⅰ/Ⅱ] button on the, control the sound is mono when display [ ] on screen and press the [ Ⅰ/Ⅱ] button on the remote control again, the sound is NICAM when display [ ] on screen.
8.Receive signal  content of sound contain stereo ,press the [Ⅰ/Ⅱ] button on the remote control, the sound is mono when display [Ⅰ] on screen and press the [Ⅰ/Ⅱ] button on the remote control again, the sound is stereo when display [Ⅱ] on screen.
9. Press the [TEXT] button on the remote control, to enter TEXT page, checking the -EXT page is normal.
10. Press the button(red, green ,yellow and blue) on the remote control, checking other content of content of TEXT pages is normal.
11. Press the [ASPECT] button continuously on remote control, The scaling “FULL-16:9-4:3” is selected in sequence and checking scaling of picture is normal.
12. Receiving signal（frequency of sound can be changed to 40HZ ～15KC）and checking has no yawp when volume is 70.
Checking
1.Receiving PHILIPS（ SECAM/BG PAL/ BG） test signal, the picture, color and sound is normal when intensity of signal is changed to 45dB.
2. Receiving PHILIPS（ SECAM/BG PAL/ BG） test signal, the picture, color and sound is normal when intensity of signal is changed to 90dB.
3. Receiving PHILIPS（ SECAM/BG PAL/ BG） test signal, the picture and sound is normal when voltage is changed to AC100V～AC240V
Factory preset
1.Receiving PHILIPS SECAM/BG PAL/ BG Test signal, check picture and sound is all right.
2. The white balance is all right after adjust the picture brightness and contrast.
3. If you hear the sound from headphone, it’s all right when headphone line is inserted to Headphone -one output socket.
4. Factory preset, as follows
1 Picture preset item is set to standard
2 Sound mode item is set to user
3 Language item is set to Russia.
4 Program number is set to No.1
5 Volume is set to 20
Posted By: FRANK at 06:07
TAG: ,