LG LED
Model: 43LH510V ZE
Chassis / Version: LD67B
Panel: LC430DUE (FJ) (A1)
T-CON: 6870C-0532C
LED driver (backlight): integrated into MainBoard
Power Supply (PSU): Adapter 19V
MainBoard: EAX66826106 (1.0)
IC MainBoard: LGE6352, H27U1G8F2BTR
Tuner: TDSN-G301D
Specifications 43LH510V
LG 43LH510V
General repair guidelines for TV LCD LED
Possible malfunctions
- LG 43LH510V TV does not turn on. There is no reaction to the remote and to the control buttons from the front panel. Indicator lights do not light or flash.
In such cases, the adapter power supply is usually faulty.
The owner of the TV can purchase an external power supply unit such as Adapter and repairing it is not always advisable. In any case, the simplest typical defects characteristic of most IIP schemes can be easily detected and eliminated after opening. It is necessary to measure the secondary output voltage, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during a short circuit in the elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, power supply, frequency-setting, damper ... as well as elements of the Negative Stabilization Feedback. The PWM chip can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
Often in such cases, there is no LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine the break in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a failure, the zener diode PN junction will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the EAX66826106 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). When repairing an MB board, you need to check its components LGE6352, H27U1G8F2BTR. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
If you suspect a malfunction of the TDSN-G301D tuner, first of all, you need to verify the correctness of the software, as well as the presence of the necessary voltage levels and pulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
Attention to users! Self-repair of the LG 43LH510V TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
The appearance of the MainBoard EAX66826106 is shown in the figure below:
EAX66826106
Main features of the device LG 43LH510V:
Installed matrix (LED-panel) LC430DUE (FJ) (A1).
The matrix control uses the Timing Controller (T-CON) 6870C-0532C.
To power the backlight LEDs, a converter is used, combined with the main board EAX66826106.
To power all the internal components of the LG 43LH510V TV, an external adapter 19V type source is used.
MainBoard - the main board (motherboard) is an EAX66826106 module, using LGE6352, H27U1G8F2BTR chips and others.
The TDSN-G301D tuner provides television reception and channel tuning.