Technical description and composition of the BBK 40LEM-1017 TV, panel type and applicable modules. The composition of the modules.BBK LED
Model: 40LEM-1017 / T2C
Chassis / Version: CV512H-B42
Panel: LY390TU2A02
LED backlight: Edge LED
LED driver (backlight): integrated into MainBoard
PWM LED driver: BIT3267
MOSFET LED driver: ME15N10
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: SMK0760F
MainBoard: CV512H-B42
IC MainBoard: CPU: 9206B 1533-DBN, SPI Flash: W25Q64JVSIG
Tuner: CDT-9NT372-RF01
Specifications 40LEM-1017 / T2C
BBK 40LEM-1017
General repair guidelines for TV LCD LED
Possible malfunctions
- The BBK 40LEM-1017 TV does not turn on, does not respond to the remote control and the control panel buttons, the indicators do not light or flash.
In this case, the main power source - the AC / DC network voltage converter, whose elements in this model are located on the MainBoard CV512H-B42 general board, may turn out to be faulty. It is necessary to measure its output voltages and, if they are absent, check the power switches (SMK0760F) and rectifier diodes for the probability of a short circuit in the converters.
In case of breakdowns of diodes in the secondary circuits, the converter can operate in emergency short circuit mode without output voltages, and during short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor at the source of the key usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM SOT23-6 PWM chips are usually checked by replacing with new ones, or obviously working.
- There is no image, but there is sound and all other functions work. Sometimes when you turn on the image for a second appears and disappears.
The most likely in these cases is a malfunction of the LED backlight. Often the cause is a malfunction of the LEDs (open circuit, short circuit ...), or the connectors of the strips (strings), less often the LED driver is malfunctioning.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the CV512H-B42 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the health of its elements - CPU: 9206B 1533-DBN, SPI Flash: W25Q64JVSIG which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
If there is no reception of television channels, but the TV is working properly from external devices, first of all you need to check the power supply of the tuner CDT-9NT372-RF01 and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
Once again, remind users! Attempts to self-repair a BBK 40LEM-1017 TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> MainBoard CV512H-B42-12.
FIRMWARE FOR SPI FLASH -----------> BBK 40LEM-1017/T2C , Main: CV512H-B42, Panel: LY390TU2A02
Service Manual with Schematic Diagram 52 pages of 2015 on the model ------------------> 28LEM-1012/T2C, 32LEM-1005/T2C, 32LEM-1007/T2C, 32LEM-1010/T2C, 32LEM-3025/T2C, 32LEX-5009/T2C, 40LEM-1010/FT2C, 40LEM-1007/FT2C, 40LEM-1005/FT2C, 40LEM-1010/T2C, 40LEM-1017/T2C, 40LEM-3025/FT2C, 40LEM-3035/FT2C, 40LEX-5009/FT2C, 43LEM-1007/FT2C, 43LEM-1009/FT2C, 43LEX-5009/FT2C, Rubin RB-32D7T2S
The appearance of the MainBoard CV512H-B42 is shown in the figure below:CV512H-B42
CV512H-B42 can be used in TVs:
BBK 40LEM-1010/FT2C (Panel CX390DLEDM), BBK 32LEM-1023/TS2C (Panel V320BJ6-Q01), BBK 32LEM-3035/T2C (Panel LS320TU9A00 NJ), BBK 32LEM-1036/TS2C (Panel DS32D6AP0113), BBK 42LEM-1009/FT2C (Panel T420HVN06.1 CX420DLEDM), DEXP F40B7000E (Panel V400HJ6-PE1 CX400DLEDM).
Main features of the BBK 40LEM-1017 device:
The matrix (LED panel) LY390TU2A02 is installed.
To power the backlight LEDs, a converter is used, combined with the main board CV512H-B42, controlled by the BIT3267 PWM controller. As the power elements of the LED driver, keys of the type ME15N10 are used.
The power module is combined with the MainBoard and is designed according to a flyback AC / DC voltage converter using PWM SOT23-6 microcircuits and power switches of the SMK0760F type.
MainBoard - the main board (motherboard) is a CV512H-B42 module, using CPU chips: 9206B 1533-DBN, SPI Flash: W25Q64JVSIG and others.
The tuner CDT-9NT372-RF01 provides the reception of television programs and tuning to channels.
Brand: BBK, Model: 40LEM-1017 / T2C.
Briefly from the TV: LCD, 720p HD, diagonal 39 "(99 cm), HDMI: 3, USB, DVB-T2 support, backlight type: Edge LED.
The composition uses MainBoard CV512H-B42 and an LCD panel (matrix) LY390TU2A02.
BBK 40LEM-1017 / T2C LED TV with LY390TU2A02 LCD display, diagonal size 39 "(99 cm) in 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlight LED. The ratio of maximum brightness to minimum (contrast) is 5000: 1. This model uses side illumination from Edge LEDs. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM , NTSC. Graphic Kaya processing and the formation of the digital signal is in 480i standards, 480p, 576i, 576p, 720p, 1080i Supported multimedia file formats:. MP3, WMA, MPEG4, MKV, JPEG.
The power of the sound system 16 W (2x8 W) provide two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI x3, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768. The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C MPEG4, DVB-T2 standards.
Overall dimensions: With stand 888x568x228 mm, Without stand 888x522x84 mm.
The mass of the TV: 9 kg.
Attention! The LY390TU2A02 panel of the BBK 40LEM-1017 / T2C LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
