BBK LED
Model: 55LEX-5022 / FT2C
Chassis / Version: CV628H-T42
Panel: W455CA030
LED driver (backlight): integrated into MainBoard
PWM LED driver: BIT3267
MOSFET LED driver: AOD4454
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: SMK10N60
MainBoard: CV628H-T42
IC MainBoard: CPU: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2
Tuner: CDT-9NT372-RF01
Technical Specifications 55LEX-5022 / FT2C
BBK 55LEX-5022
General repair guidelines for TV LCD LED
Possible malfunctions
- BBK 55LEX-5022 does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
In this case, first of all, you should check the operability of the main power source - AC / DC network voltage converter, all of whose elements are located on the MainBoard CV628H-T42 board. It is necessary to measure its output voltages, and in case of their absence (full or partial), it is necessary to check the serviceability of power switches (SMK10N60) of converters and rectifier diodes for the presence of a possible short circuit.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM SOT23-6 PWM chips are usually checked by replacing with new ones, or obviously working.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
Usually in such cases there is no backlight LED-panel (matrix). Usually the cause of the malfunction is in the breakage of the LEDs, or in the connectors of the LED strips, but sometimes the LED driver also turns out to be faulty.
When trying to detect a break in the LED lines, it should be taken into account that it is difficult to do this without disassembling the panel. For example, a current source is needed to open PN junctions connected in series.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the CV628H-T42 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the health of its elements - CPU: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2 which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
If the TV works normally from external devices, but does not tune into television channels, the tuner CDT-9NT372-RF01 may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention TV owners! Attempts at self-repair of BBK 55LEX-5022 are not recommended by the manufacturer and can lead to serious negative consequences!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> BBK 55LEX-5022 Chassis CV628H-T42
Schematic Diagrams 14 pages of 2015 on ------------------> 32LEM-3081/T2C, 32LEX-5007/T2C, 32LEX-5025/T2C, 40LEX-5007/T2C, 40LEX-5007/FT2C, 40LEX-5025/FT2C, 40LEX-5035/FT2C, 43LEX-5007/FT2C, 50LEX-5022/FT2C, 50LEX-5025/FT2C, 55LEX-5022/FT2C.
The appearance of the MainBoard CV628H-T42 is shown in the figure below:
CV628H-T42
CV628H-T42 can be used in TVs:
BBK 43LEX-5009/FT2C (Panel LC430DUY (SH)(A1)), BBK 40LEX-5025/FT2C (Panel V400HJ6-PE1 DLEDSV400FHD), BBK 32LEX-5027/T2C (Panel V320BJ6-Q01 Rev.C1), SUPRA STV-LC40ST900FL (Panel V400HJ6-PE1).
Main features of the BBK 55LEX-5022 device:
Installed matrix (LED-panel) W455CA030.
To power the backlight LEDs, a converter is used, combined with the main board CV628H-T42, controlled by a BIT3267 PWM controller. As power elements of the LED driver, keys of the AOD4454 type are used.
The power module is combined with the MainBoard and is made according to the scheme of a flyback AC / DC voltage converter using PWM SOT23-6 microcircuits and power switches of the SMK10N60 type.
MainBoard - the main board (motherboard) is a CV628H-T42 module, using CPU chips: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2 and others.
The tuner CDT-9NT372-RF01 provides the reception of television programs and tuning to channels.
Brand: BBK, Model: 55LEX-5022 / FT2C.
Shortly from the TV: LCD, 1080p Full HD, diagonal 55 "(140 cm), Smart TV (Android), Wi-Fi, HDMI: 2, USB: 3, there is support for DVB-T2, backlight type: Edge LED.
The composition uses MainBoard CV628H-T42 and LCD-panel W455CA030. The power supply is combined with the MainBoard.
BBK 55LEX-5022 / FT2C LED TV with W455CA030 LCD display, 55 "(140 cm) diagonal size in 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. The ratio of maximum brightness to minimum (contrast) is 12000: 1. This model uses side illumination from Edge LEDs.The design and technical capabilities of the TV include watching programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphical decomposition according to the standard 1080p (Full HD).
55LEX-5022 / FT2C has built-in SMART Software and pre-installed Android Operating System. Connecting to the Internet can be done via Wi-Fi. The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG. Stereo sound is realized by two built-in speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI x2, MHL, USB x3, Ethernet (RJ-45), Wi-Fi 802.11n. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080. The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C MPEG4, DVB-T2 standards.
Overall dimensions: With stand 1251x782x310 mm, Without stand 1251x730x92 mm.
TV Weight: 19 kg.
Attention! The BBK 55LEX-5022 / FT2C LED TV panel W455CA030 is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.