Technical description and composition of the BBK LEM1961 TV, panel type and applicable modules. The composition of the modules.BBK LED
Model: LEM1961
Chassis / Version: MSTV2409-ZC01-01
Panel: HM185WX1-400 // HM185WX1-100
LED backlight: LED185D44-ZC14-03 (A)
T-CON: HM185WX1-400.X0.0
LED driver (backlight): integrated into MainBoard
PWM LED driver: AP3039AM-G1, AP3608EM
MOSFET LED driver: MDD1951
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MainBoard: MSTV2409-ZC01-01 M32 / A41974 / 13
IC MainBoard: TSUMV59XUS, SPI Flash: MX25L3206E, PT2308-S
Tuner: NoName
Technical Specifications LEM1961
BBK LEM1961
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The BBK LEM1961 TV does not turn on and does not show any signs of turning on, does not respond to the control buttons or to the remote control.
First of all, in such cases, you should verify the operability of the common switching power supply (IIP) - AC / DC voltage converter of the mains voltage. All source elements in this TV model are located on the MainBoard MSTV2409-ZC01-01 main board. It is necessary to measure its output supply voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for the probability of breakdown in PN semiconductor junctions.
In case of diode breakdowns in the secondary circuits, the converter can operate in emergency short-circuit mode without output voltages, and during short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor at the source of the key usually breaks.
Breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback circuits (OOS) of stabilization. PWM controllers (PWM) PWM SOT23-6, if they do not have visible damage to the case and open short circuit between the terminals, are usually checked by replacement.
- There is no image, there is sound, it responds to the remote. Or the image may appear for a second when turned on and immediately disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a failure, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the MSTV2409-ZC01-01 motherboard should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, update or replace the software (software). If it is not possible to replace the MB board (SSB), you need to check the health of its elements - TSUMV59XUS, SPI Flash: MX25L3206E, PT2308-S. Defective components should be replaced.
In cases where there is no tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the NoName tuner. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
Attention TV owners! Attempts at self-repair of BBK LEM1961 are not recommended by the manufacturer and can lead to serious negative consequences!
To reduce the backlight current in LED drivers with the AP3039AM controller and the AP3608EM terminal stage (AP3039AM-G1 & AP3608EM-G1), the AP3608EM (AP3608E) microcircuit should proportionally increase the resistor from terminal 14 (ISET) to the housing. The maximum current in each channel (in milliamperes) for the Rset resistor (in kilo-ohms) is determined from the ratio 1.194V / Rset. In channels connected in parallel, the currents add up.
FIRMWARE FOR SPI FLASH -----------> BBK LEM1961, Main: MSTV2409-ZC01-01 M32/A41974/13, Panel: HM185WX1-100
The appearance of the MainBoard MSTV2409-ZC01-01 is shown in the figure below:MSTV2409-ZC01-01
MSTV2409-ZC01-01 can be used in TVs:
BBK LEM1961 (Panel HM185WX1-400), Haier LE32M600 (Panel LK315T3HB94), Haier LE24M600F (Panel M240HTN01.0), HAIER LE22M600F (Panel LC215DT8A), HAIER LE24M660 (Panel V236BJ1-P03), MYSTERY MTV-3022LW (Panel V290BJ1-PE1), MYSTERY MTV-1923LW (Panel HM185WX3-400).
Main features of the BBK LEM1961 device:
Installed matrix (LED-panel) HM185WX1-400 or HM185WX1-100.
The matrix control uses the Timing Controller (T-CON) HM185WX1-400.X0.0.
To power the backlight LEDs, a converter is used, combined with the main board MSTV2409-ZC01-01, controlled by the AP3039AM-G1, AP3608EM PWM controller. As the power elements of the LED driver, keys of the MDD1951 type are used.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is an MSTV2409-ZC01-01 module, using TSUMV59XUS, SPI Flash chips: MX25L3206E, PT2308-S and others.
The NoName tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: BOE
Model: HM185WX1-400
Type: a-Si TFT-LCD, Panel
Diagonal size: 18.5 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 409.8x230.4 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 200 cd / m²
Contrast Ratio: 600: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 72%
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 10S4P WLED Without Driver
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 5.0V
Brand: BBK, Model: LEM1961.
Briefly from the TV: LCD, 720p HD, diagonal 19 "(48 cm), HDMI: 2, USB, backlight type: Edge LED.
The composition uses MainBoard MSTV2409-ZC01-01 and the LCD panel (matrix) HM185WX1-400, or HM185WX1-100. The power supply is combined with the MainBoard.
LED TV BBK LEM1961 with LCD HM185WX1-400, diagonal size 19 "(48 cm) 16: 9 format. The required brightness of the screen is 250 cd / m² LED backlight LED. The ratio of maximum brightness to minimum (contrast) is 800 : 1. This model uses side illumination from Edge LEDs. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic Digital signal processing and generation takes place in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, RGB, VGA, HDMI x2, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV in the operating mode from the network is 30 watts.
Dimensions: With stand 451x325x150 mm, Without stand 451x284x43 mm.
TV Weight: 2.8 kg.
Attention! The HM185WX1-400 panel of the BBK LEM1961 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
