Technical description and composition of the BBK LEM3284F TV, type of panel and applicable modules. The composition of the modules.BBK LED
Model: LEM3284F
Chassis / Version: MSTV2407-ZC01-01
Panel: HV320WXC-200
LED driver (backlight): integrated into MainBoard
PWM LED driver: AP3039AM, AP3608EM-G1
Power Supply (PSU): integrated into MainBoard
PWM Power: SG6848 (PWM SOT23-6)
MainBoard: MSTV2407-ZC01-01
IC MainBoard: CPU: MST6E182, SPI Flash: 25Q32
Tuner: F35WT-2A-E
Appearance
BBK LEM3284F
General repair guidelines for TV LCD LED
Repair of electronic equipment usually begins with its external inspection and diagnosis of the malfunction. In this case, you should examine all the internal components of the BBK LEM3284F TV, as well as the external elements of the housing. It often happens that visible damage to elements or connections helps determine the direction of the troubleshooting. Ring cracks in the soldering of the leads of the heating elements, swollen electrolytic capacitors, a charred paint layer on the resistors - all this for the repairman can be a significant clue in the assumptions about the causes and consequences of the malfunction.
If the BBK LEM3284F does not turn on, no control lights on the front panel light up or blink; therefore, there is a very high probability of a power module malfunction. In some cases, only the processor power regulator may be faulty. Diagnostics and repair of the common power supply should always begin with a check of the mains fuse and the condition of the electrolytic capacitors of the secondary rectifier filters. Defective and swollen capacitors should be replaced with new ones. If the fuse breaks, it is advisable to check for a breakdown, first of all, all the power semiconductor elements of the converter and the diode bridge of the rectifier network, as well as the large electrolytic capacitor of the filter of the rectifier network.
It should be borne in mind that in the practice of repair it is extremely rare that key transistors in switching power supplies (SMPS) fail for no reason that should be sought by checking other components, for example, a breakdown of the key can provoke faulty elements of the damper circuits, or dried electrolytic capacitors or dangling primary resistors BP circuits involved in the stabilization process. In this case, all semiconductor elements of the strapping of the PWM controller chip are subject to verification, which it is desirable to verify by replacement.
Sometimes the BBK LEM3284F TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a high probability of a malfunction of the HV320WXC-200 panel backlight LED converter, or a break in the LED circuit is possible. In such cases, first of all, it is necessary to verify the serviceability of all the electrolytic capacitors of the filter by supplying the LED driver itself, including the power supply unit (power supply unit).
To check the health of the LEDs and contact connections in their power circuit, the panel must be disassembled.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required.
Repair of the MSTV2407-ZC01-01 motherboard must begin with the diagnosis and verification of all linear stabilizers or power converters of its microcircuits. Sometimes it may be necessary to update the software (software) - flashing FLASH or EEPROM.
In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its chips Cpu: MST6E182, SPI Flash: 25Q32 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Before replacing the F35WT-2A-E tuner, if there is no tuning for the channels, you must first check the supply voltage at its terminals.
Owners and users of the BBK LEM3284F TV must remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> MSTV2407-ZC01-01 Schematic diagram
FIRMWARE FOR SPI FLASH -----------> BBK LEM3284F, Main: MSTV2407-ZC01-01, Panel: HV320WXC-200
To reduce the backlight current in LED drivers with the AP3039AM controller and the AP3608EM terminal stage (AP3039AM-G1 & AP3608EM-G1), the AP3608EM (AP3608E) microcircuit should proportionally increase the resistor from terminal 14 (ISET) to the housing. The maximum current in each channel (in milliamperes) for the Rset resistor (in kilo-ohms) is determined from the ratio 1.194V / Rset. In channels connected in parallel, the currents add up.Repair MainBoard
The appearance of the MainBoard MSTV2407-ZC01-01 is shown in the figure below:
MSTV2407-ZC01-01
MSTV2407-ZC01-01 motherboard is combined with a power module. The processor is MST6E182VG, or MST6E181VG, made using BGA technology. Repair of the power module is carried out according to conventional technology, starting with checking its power elements. The following is a functional check of the converters for the processor power: + 1.3V, + 1.8V, 3.3V, based on SY8008B PWM controllers. The power supply of the built-in DDR 2.5V is generated from a 3.3V source using the P-N junction of the 1N4001 diode (3.3V-0.8V = 2.5V). Standby mode is organized from the linear stabilizer series 1117-3V3. The LCD panel is powered by either 5V or 12V, depending on the type of panel used.
MSTV2407-ZC01-01 can be used in TVs:
BBK LEM2249HD Ver2 (Panel LM215DT5D), BBK LEM2284F (Panel M215HG-LE4 Rev.C3), BBK LEM2681F (Panel V260H1-LE10 Rev. C1 ), BBK LEM2682 LEM2682DT (Panel V260B2-LE11 Rev.C1), BBK LEM3284F (Panel HV320WXC-200), Haier LE32T1000 (Panel T320XVN09.0), MYSTERY MTV-2224LW (Panel M215HG-LE4 Rev.C3), MYSTERY MTV-3222LW (Panel T320XVN01.0), MYSTERY MTV-1924LW (Panel V185B1-L17), MYSTERY MTV-3018LW (Panel V290BJ1-PE1), MYSTERY MTV-1911LW (Panel HT185WX7-100), MYSTERY MTV-1922LW (Panel V185B1-L17), MYSTERY MTV-1913LW (Panel HT185WX7-100), MYSTERY MTV-3218LW (Panel HV320WX2-20A), MYSTERY MTV-1918LW (Panel V185B1-L17), MYSTERY MTV-2213LW (Panel M215HGE-L10), MYSTERY MTV-2222LW (Panel M215HG-LE4 REV.C3), MYSTERY MTV-2418LW (Panel HM236WUA-100), MYSTERY MTV-2424LW (Panel HM236WU8-100), MYSTERY MTV-1914LW (Panel V185B1-L15 Rev.c1), MYSTERY MTV-3223LW (Panel LK315T3HB94), MYSTERY MTV-2422LW (Panel HM236WU8–100), MYSTERY MTV-3224LW (Panel T320XVN09.0), MYSTERY MTV-2218LW (Panel CLAA215FA10), MYSTERY MTV-1911WL (Panel V185B1-L15 REV.C1), MYSTERY MTV-3221LW (Panel HV320WX2-268), MYSTERY MTV-2211W (Panel M215HG-LE4 ).
Main features of the BBK LEM3284F device:
Installed matrix (LED-panel) HV320WXC-200.
To power the backlight LEDs, a converter is used, combined with the main board MSTV2407-ZC01-01, controlled by the AP3039AM, AP3608EM-G1 PWM controller.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter using SG6848 microcircuits (PWM SOT23-6).
MainBoard - the main board (motherboard) is an MSTV2407-ZC01-01 module, using Cpu microcircuits: MST6E182, SPI Flash: 25Q32 and others.
The F35WT-2A-E tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: BOE
Model: HV320WXC-200
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: ADS, Normally Black, Transmissive
Active Area: 697.685x392.256 mm
Surface: Antiglare (Haze 10%), Hard coating (3H)
Brightness: 380 cd / m²
Contrast Ratio: 1200: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 8 (G to G)
Frequency: 60Hz
Lamp Type: 80 pcs WLED Embedded (LED Driver)
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
