Technical description and composition of the HAIER LE32T1000 TV, type of panel and applicable modules. The composition of the modules.Haier LED
Model: LE32T1000
Chassis / Version: MSTV2407-ZC01-01
Panel: T320XVN09.0
T-CON: T320XVN01.0 32T21-C05
LED driver (backlight): integrated into MainBoard
PWM LED driver: AP3039AM, AP3608E
Power Supply (PSU): integrated into MainBoard
PWM Power: OB2273 (PWM SOT23-6)
MainBoard: MSTV2407-ZC01-01
IC MainBoard: CPU: MST6E182VG-LF-Z1, SPI FLASH: Winbond 25Q32BVS1G, Eeprom: 24C16, Sound: TDA1517
Tuner: F35WT-2A-E
Specifications LE32T1000
HAIER LE32T1000
General repair guidelines for TV LCD LED
Possible malfunctions
- The Haier LE32T1000 TV does not turn on, does not respond to the remote control and the control panel buttons, does not blink with any indicators.
In such cases, the fault is usually the power source, all of whose elements are on the MainBoard main board: MSTV2407-ZC01-01. It is necessary to measure its secondary output voltages, and in case of their absence, check the serviceability of the power switches and rectifier diodes of the AC / DC converter for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in short circuit mode, and when a short circuit occurs in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power switch may be PWM (PWM) OB2273 (PWM SOT23-6). It is checked only by replacement with a known good one.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
As a rule, in such cases there is no display backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as a health indicator. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the MSTV2407-ZC01-01 motherboard should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, update or replace the software (software). Board repair and replacement of CPU chips: MST6E182VG-LF-Z1, SPI FLASH: Winbond 25Q32BVS1G, Eeprom: 24C16, Sound: TDA1517 are made with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
If the TV works normally from external devices, but does not tune into television channels, the tuner F35WT-2A-E may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention TV owners! Attempts at self-repair of Haier LE32T1000 are not recommended by the manufacturer and can lead to serious negative consequences!
FIRMWARE FOR SPI FLASH --------------> Haier LE32T1000, Main: MSTV2407-ZC01-01, Panel: T320XVN09.0
To reduce the backlight current in LED drivers with the AP3039AM controller and the AP3608EM terminal stage (AP3039AM-G1 & AP3608EM-G1), the AP3608EM (AP3608E) microcircuit should proportionally increase the resistor from terminal 14 (ISET) to the housing. The maximum current in each channel (in milliamperes) for the Rset resistor (in kilo-ohms) is determined from the ratio 1.194V / Rset. In channels connected in parallel, the currents add up.
The appearance of the MainBoard MSTV2407-ZC01-01 is shown in the figure below:MSTV2407-ZC01-01
MSTV2407-ZC01-01 motherboard is combined with a power module. The processor is MST6E182VG, or MST6E181VG, made using BGA technology. Repair of the power module is carried out according to conventional technology, starting with checking its power elements. The following is a functional check of the converters for the processor power: + 1.3V, + 1.8V, 3.3V, based on the SY8008B PWM controllers. The power supply of the built-in DDR 2.5V is generated from a 3.3V source using the P-N junction of the 1N4001 diode (3.3V-0.8V = 2.5V). Standby mode is organized from the linear stabilizer series 1117-3V3. The LCD panel is powered by either 5V or 12V, depending on the type of panel used.
MSTV2407-ZC01-01 can be used in TVs:
BBK LEM2249HD Ver2 (Panel LM215DT5D), BBK LEM2284F (Panel M215HG-LE4 Rev.C3), BBK LEM2681F (Panel V260H1-LE10 Rev. C1 ), BBK LEM2682 LEM2682DT (Panel V260B2-LE11 Rev.C1), BBK LEM3284F (Panel HV320WXC-200), Haier LE32T1000 (Panel T320XVN09.0), MYSTERY MTV-2224LW (Panel M215HG-LE4 Rev.C3), MYSTERY MTV-3222LW (Panel T320XVN01.0), MYSTERY MTV-1924LW (Panel V185B1-L17), MYSTERY MTV-3018LW (Panel V290BJ1-PE1), MYSTERY MTV-1911LW (Panel HT185WX7-100), MYSTERY MTV-1922LW (Panel V185B1-L17), MYSTERY MTV-1913LW (Panel HT185WX7-100), MYSTERY MTV-3218LW (Panel HV320WX2-20A), MYSTERY MTV-1918LW (Panel V185B1-L17), MYSTERY MTV-2213LW (Panel M215HGE-L10), MYSTERY MTV-2222LW (Panel M215HG-LE4 REV.C3), MYSTERY MTV-2418LW (Panel HM236WUA-100), MYSTERY MTV-2424LW (Panel HM236WU8-100), MYSTERY MTV-1914LW (Panel V185B1-L15 Rev.c1), MYSTERY MTV-3223LW (Panel LK315T3HB94), MYSTERY MTV-2422LW (Panel HM236WU8–100), MYSTERY MTV-3224LW (Panel T320XVN09.0), MYSTERY MTV-2218LW (Panel CLAA215FA10), MYSTERY MTV-1911WL (Panel V185B1-L15 REV.C1), MYSTERY MTV-3221LW (Panel HV320WX2-268), MYSTERY MTV-2211W (Panel M215HG-LE4 ).
Key Features of HAIER LE32T1000:
Installed matrix (LED-panel) T320XVN09.0.
The matrix control uses the Timing Controller (T-CON) T320XVN01.0.
To power the backlight LEDs, a converter is used, combined with the main board MSTV2407-ZC01-01, controlled by the AP3039AM, AP3608E PWM controller.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using OB2273 microcircuits (PWM SOT23-6).
MainBoard - the main board (motherboard) is an MSTV2407-ZC01-01 module, using CPU chips: MST6E182VG-LF-Z1, SPI FLASH: Winbond 25Q32BVS1G, Eeprom: 24C16, Sound: TDA1517 and others.
The F35WT-2A-E tuner provides television reception and channel tuning.
HAIER LE32T1000 TV with T320XVN09.0 LCD, 32 "(81 cm) diagonal size in 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 4000000: 1 is achieved by special control of the LEDs. The LED panels of this TV are equipped with end LED backlighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog x PAL, SECAM, NTSC systems. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats: MP3, MPEG4, JPEG.
The power of the sound system 16 W (2x8 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, RGB, VGA, HDMI x2, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV working in the network mode is 75 watts.
Overall dimensions: With stand 747x495x180 mm, Without stand 747x452x46 mm.
Attention! The T320XVN09.0 panel of the HAIER LE32T1000 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
