Technical description and composition of the HAIER LE39M600F TV, type of panel and applicable modules. The composition of the modules.HAIER LED
Model: LE39M600F
Chassis / Version: MSTV2410-ZC01-01
Panel: V390HJ1-P02
LED backlight: 30339011213, 30339011214, 30339011215, 30339011216
LED driver (backlight): integrated into PSU
PWM LED driver: OB2263, AP3616M28-G1
MOSFET LED driver: MDF0765
Power Supply (PSU): TV4205-ZC02-01
PWM Power: FAN7930 (PFC), OB2263, OB2273
MOSFET Power: FDPF18N50, MDF0765
MainBoard: MSTV2410-ZC01-01
IC MainBoard: CPU: TSUMV59XUS, SPI FLASH: KH25L3206E
Tuner: NoName
Control: IR: TV3215-ZC25-05 (A) 303C3215235
Technical Specifications LE39M600F
HAIER LE39M600F
General repair guidelines for TV LCD LED
Possible manifestations of defects
- HAIER LE39M600F does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
Most often, with such manifestations, the main TV4205-ZC02-01 power module is found to be faulty. It is necessary to verify the presence of its output voltages and, if they are completely absent, check the power switches (FDPF18N50, MDF0765) and rectifier diodes for possible short circuit.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And during short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) FAN7930 (PFC), OB2263, OB2273, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the MSTV2410-ZC01-01 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its CPU chips: TSUMV59XUS, SPI FLASH: KH25L3206E and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Before changing the NoName tuner, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured at the corresponding tuner pins and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Entrust repair to professionals with sufficient experience in the field of repair of electronic equipment.
schematic manual --------------> TV4205-ZC02-01 Schematic diagram
FIRMWARE FOR SPI FLASH ---------------------> HAIER LE39M600F, Main: MSTV2410-ZC01-01, Panel: V390HJ1-P02
To reduce the backlight current in LED drivers with the AP3616M28-G1 terminal stage, the total resistance of the resistors from terminal 22 (ISET AP3616M28) to the housing should be proportionally increased. The maximum current in each of the 16 channels is 75 mA. To increase the current in the diodes, the channels are connected in parallel. The current in milliamperes in each channel is determined from the calculation of 1560 * 1.194 / Rset, where Rset is the resistance from the ISET output to the housing in kilo-ohms.
Repair MainBoard
The appearance of the MainBoard MSTV2410-ZC01-01 is shown in the figure below:
MSTV2410-ZC01-01
The appearance of the power supply
Key Features of HAIER LE39M600F:
Installed matrix (LED panel) V390HJ1-P02.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by the OB2263 PWM controller, AP3616M28-G1. As power elements of the LED driver, keys of the MDF0765 type are used.
The necessary supply voltages for all nodes of the TV HAIER LE39M600F are generated by the TV4205-ZC02-01 power module, or its analogs using FAN7930 (PFC), OB2263, OB2273 chips and power switches of the FDPF18N50, MDF0765 type.
MainBoard - the main board (motherboard) is an MSTV2410-ZC01-01 module, using CPU chips: TSUMV59XUS, SPI FLASH: KH25L3206E and others.
The NoName tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: V390HJ1-P02
Type: a-Si TFT-LCD, CELL
Diagonal size: 39 inch
Resolution: 1920x1080, FHD
Display Mode: MVA, Normally Black, Transmissive
Active Area: 853.92x480.33 mm
Surface: Antiglare (Haze 3.5%), Hard coating (3H)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 5.8% (with Polarizer)
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit)
Response Time: 8.5 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V
HAIER LE39M600F TV with V390HJ1-P02 LCD, 39 "(99 cm) diagonal size in 16: 9 format. The required screen brightness of 280 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 4000000: 1 is achieved by special control of the LEDs. V The LED panels of this TV are equipped with edge LED backlighting - Edge LED.The design and technical capabilities of the TV include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphical decomposition according to the standard 1080p (Full HD). high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, JPEG.
The power of the sound system 16 W (2x8 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x2, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
Overall dimensions: With a support 892x574x210 mm, Without a support 892x540x63 mm.
Attention! The panel V390HJ1-P02 of the HAIER LE39M600F LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
